Linksys Wireless Router :: Wrvs4400n - All Computers Can Access Printers (Port 3)
Jun 18, 2008
I have a linksys wrvs4400n router on which:The wireless computers are connected to the home network (v lan 1)Port 1 is connected to the home network (v lan 1)Port 2 is connected to the office network (v lan 2)And the printers are connected to port 3.Now I'd like to setup the router in such a way that all computers have access to the printers (port 3), but I don't know what v lan settings I have to use on port 3, or if it is even possible...
View 5 Replies
ADVERTISEMENT
Feb 11, 2011
I understand we cannot view computers that in different workgroup though in the same network. But when I try to add printer it lists even those local printers that is attached and shared in different workgroup.
View 1 Replies
View Related
Feb 17, 2012
I've been configured my device to forward FTP service to my server, however, I can't access this service outside from my network. I used Single Port Forward and not worked, after, I've used Port Range Forwarding starting in 20 to 21 and not work again.I've sniffed my computer and I've found just 3 outsides packages without response.I've tried with directly IP ADDR and DYNDNS ADDR, but neither one or other worked.
View 1 Replies
View Related
Oct 13, 2011
I have a DGL-4500 D-Link router as a base. And a DAP 1522 Ethernet Bridge I use to connect 3 devices and another router I am looking to host a media Server for the house(on the bridge).
View 5 Replies
View Related
Jul 1, 2012
Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again.
View 1 Replies
View Related
Feb 16, 2011
One computer is an iMac running Snow leopard and the other is running Win 7. I wish to switch either computer to any of the two printers.
View 1 Replies
View Related
May 9, 2012
I have a Comcast SMC8014 cable modem connected to a Linksys BEFSR81 Router and a Netgear Prosafe 24-port 10/100 switch connected to one of the LAN ports on the router. There are many PCs connected to this network, including one used as a file server. I would like to add a LINKSYS WRT54GL wireless router to this mix to allow visitors wireless access to the internet and network printers but NOT allow access to the file server
View 7 Replies
View Related
Nov 2, 2011
Recently installed an E4200 router to an MacPro following the setup as directed by Cisco Connection (connect Ethernet to router and then computer to router.) The wireless and the hard-wire connectivity works fine with accessing the internet. However, we have lost the ability to connect to other computers on our LAN via the Shared folder connection. This is usually accessed via the Sidebar (see image)
However with the E4200 in the mix, all we see is the router per its "given name" (what it was named on installation). I have tried to follow the advice mentioned in other threads, such as "Can't access network shares with E3000" and nothing worked-- and those threads seemed to apply to Windows and PCs anyway.
View 6 Replies
View Related
Nov 17, 2012
I have a WRT54G that has worked fine for years, with some PCs hooked up with Ethernet and various other devices connected wirelessly. I came home this afternoon and nothing going through the router could connect to the internet. I've made no changes to anything recently.
I did troubleshooting with Comcast, and we determined that when their modem was hooked up directly to my computer then that computer could connect to the net. Problem solved as far as they are concerned--my router is busted. But I can still connect to the router, and enter its admin screen, and everything looks fine there. The computers on the router can all see each other. So the router is working.
Once I hooked it back up to the modem my computers all lost their internet, but the router does get an IP successfully from Comcast. And it even assigns IPs to my computers that are hooked up to it. It's just that for some reason they still cannot get past the router.I used the ping function in the router admin site and the router pinged Google no problem. My PCs can ping the router without difficulty. But the computers cannot ping Google.
I've tried every combination of power cycles and reboots you can name. I've tried duplicating the MAC address of the PC that connected to the internet onto my router. None of it has made any difference.
View 5 Replies
View Related
Jun 10, 2011
Will all usb printers be able to connect to the e3200 by usb with the firmware update? If not, what printers will be supported?
View 9 Replies
View Related
Apr 23, 2012
I have a WRVS4400n and a CentOS server that I need to enable a SSH access to from WAN. I created a single port forward rule to open port 22 and forward to server (which address is 192.168.41.3) However ssh connect doesn't happen, the command "ssh user@{external_IP}" times out after 20 seconds. If I connect my server directly to modem through outside interface - I have no problems connecting to it. Once it's behind router - no luck. I even added same rule for UDP, not sure if it's needed, but it definitely didn't hepl. The router is on firmware version 2.0.1.3, version on a bottom is 2.
View 4 Replies
View Related
Feb 1, 2013
I have a Linksys WRT54GS router that I have installed dd-wrt on.My household is overloaded with wireless devices, and living in a home of 6, speeds for everyone seem to slow down drastically later at night when everyone is simultaneously connected and streaming media -- whether it be Netflix, YouTube, etc.. My typical speed wired to the router with no other connections is around 25 mb/s down and 1-2 mb/s up.Obviously, it's going to slow to a crawl when we have an iPad, 3 iPod touches, an iPhone, a Wii (playing Netflix) and 4 PCs all connected simultaneously.What I need to do is give my personal computer priority and throttle all other devices. So that I myself will have decent speeds while hampering all of the other household connections. I rely on those speeds for my job and that should have priority over my brother watching music videos on YouTube.
View 1 Replies
View Related
Jan 26, 2012
Had the following network (fully functional) for last 3 years: Modem (netopia dsl 192.168.1.254) router (linksys wrt54gs 192.168.1.1) WAP1 (linksys wrt54g2 192.168.1.250) and WAP2 (Linksys wrt54g2).I was always able to click on Devices and Printers in Win 7 and would see the equipment displayed.I could also access the router and wireless access points by typing their address in my browser. The modem failed after 5 years.I purchase a new Netgear N300 ADSL2+Modem Router (DGN2200)and replaced the failed modem and attached router.I made no changes to either WAP's.Everything works just fine (after about 30 minutes on phone with Netgear Tech to configure), but now none of the equipment displays in Devices and Printers. Also, I cannot connect to either WAP by typing their address in browser.I can see the Netgear device when I click on "network" in file manager.It displays a model number and is labeled a "gateway".
I'm just curious as to why I am no longer able to "see" or access the devices. Looks like I would have to actually pull the WAP's and connect to them directly if I needed to change their configurations.
View 1 Replies
View Related
Apr 21, 2012
I bought a new e2500 and it is working fine, all but port forwarding. This is not even close to my first router and I am advanced when it comes to setting these up. I have tried for days to get port 80 to open up and it refuses. Now I do notice that when you access the router setup through a web interface, it uses port 80. I have forwarded port 80 to the ip address of the device, put in a reservation in DHCP with MAC address, etc. etc. and still nothing. Heck, I have even turned that specific device IP into a DMZ, and it STILL will not work.For the record, I had an e2000 set up the exact same way and it worked just fine and I was able to access port 80.
View 6 Replies
View Related
Feb 26, 2012
I need to configure a network in 1 small office space that segregates 2 company domains but allows them to share an Internet connection, a WAP, a couple of printers, and a non-Cisco VoIP phone system. And, it needs to provide guest access to the internet and printers via wireless. I have a SG300-28P, an SA520W, and a WAP2000 to make it all happen. [code]
View 3 Replies
View Related
Nov 22, 2011
I've got an out of the box WRVS4400N and it will not pick up a DHCP IP from the ISP.
I reset to factory defaults, tried another ISP, returned and got a second wrvs4400n all the same results - no IP address on the WAN port. The internet LEDs are blinking but no IP on WAN port and no internet connection from a laptop connected to wrvs4400n.
I even tried turning of the firewall too.
Is there something with these routers that needs to be done for internet access?
Most typical small routers are just set up as a DHCP client on the WAN side and DHCP server on the LAN side.
View 2 Replies
View Related
Jul 19, 2012
I have 2 WRVS4400N's availible to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies
View Related
Jan 13, 2012
I'm keep failing my pci compliance test I have a wrvs4400n and I keep getting "firewall udp packet source port 53 ruleset bypass" i've blocked port 53 but keep getting rejected. How to set the router?
View 1 Replies
View Related
Feb 26, 2007
I would like to connect to the built in accounts on the wrvs4400n from a mac VPN client. I am new VPN and have not found much information on how to establish this connection. Since Linksys seems determined to rely on Quickvpn, and provides no information on what it is actually doing under the hood I can not figure out how to configure any of the VPN clients available, or the built in VPN tools, for OS X (10.4.8). The only information I have been able to find seems to relate to setting up VPN Tunnels, or running a server behind the wrvs4400n and using one of the VPN passthrough options. I would like to connect directly to the built in accounts, how to set this up on a mac?
View 7 Replies
View Related
Feb 7, 2013
I am wanting to access my IP camera over the Internet. I am not a computer wiz by any stretch and after a couple of failed attempts. My ISP is Comcast and they say that I have dynamic dns and should have no issues viewing my cameras. I know how to get to the port forwarding area of the router but am confused as to which ports to forward. The set up instructions for the camera (Airsight) suck. Screen shots of the set up don't match the actual router
View 7 Replies
View Related
Sep 18, 2012
I have recently purchased an EA4500 router. I assigned my sons XBOX a static IP via DHCP reservation (outside of the standard DHCP range). I set up single port forwarding on all the standard xbox required ports. Once I click the "enabled" box, I am unable to access the internet from any of the computers connected to the router. If I uncheck the enable box, I am instantly able to access the internet.
View 4 Replies
View Related
Jul 12, 2012
I recently opened the ports used by Xbox Live: Port 88 (UDP)Port 3074 (UDP and TCP)Port 53 (UDP and TCP)Port 80 (TCP)I am able to use xbox live once these ports are opened but once they are enabled, I can not get wireless internet. The xbox is connected to the router with a cable so it isn't experiencing this probem. My laptop and phone are able to identify the network and join but there is no internet access.
If I disable these ports, everything goes back to normal.
View 1 Replies
View Related
Apr 27, 2012
I would like to automatically check if the VPN is up or down, simple enough, and respond by bumping it, disconnecting and connecting, as needs be (not so simple I think).This through a C# program using HttpWebRequest and HttpWebResponse.It's simple enough to login to the VPN page using known credentials. Done deal. And also very easy to check a couple of known patterns in the VPN table.When I determine I need to bump the VPN, how do we simulate the form submission and/or call to the JavaScript programmatically? we're using a Linksys WRVS4400N router, firmware version V1.1.13.
View 2 Replies
View Related
Feb 26, 2012
I cant get the WRVS4400N to connect to my cable modem. The WAN link light isnt even lighting up. Im wondering if this unit is bad out of the box. Is there a setting im missing to get them to talk to one another. This is no mention in any of the manuals.
Connections: - The "Internet" port on the WRVS4400N to the "Network" port on my cable modem (No link light)
Here is what i have verified at this point: - My old router connects instantly to the modem when plugged in (Same cable) - When i plug my laptop into the WAN port on the WRVS4400N i get a link light. When i plug the modem into the WAN port...nothing.
View 1 Replies
View Related
Jan 24, 2013
I get a "IP address conflict" message on my wireless network. Using a WRVS4400n wireless router with the latest firmware that is set to PPoE. Motorola 336 dsl modem is set to bridge mode. My network has 2 computers attached: hardwire desktop and wireless connection to laptop. When I contacted ATT support, they said the problem is in the wireless modem. Are there some settings in the WRVS4400n that must be set to insure that each computer gets a different IP address?
View 2 Replies
View Related
Nov 8, 2009
I've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's. I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?
View 3 Replies
View Related
Aug 29, 2011
I have a WRVS4400N setup as a main router for one of our bays. For wired connections it is working with no problems. When I first installed it it ran fine for wireless as well. I was trying to get WDS to work and at some point the wireless stopped working. My laptop can no longer connect to it and often cannot see it when doing a scan for networks. I have already checked that it isn't a problem with the laptop, that there are not other networks causing interferance, and even tried resetting to default configs.
View 1 Replies
View Related
Sep 4, 2012
What would be the best way to connect 10 computers to a 4 port router?
View 1 Replies
View Related
Nov 29, 2011
I just purchased a Toshiba Thrive tablet and I can't get it to connect to my wireless router. My router (WRVS4400N) works flawlessly with my laptop and desktop. I have spoken to a Cisco tech rep and they assured me that there is not a compatibility problem with the WPA-Personal setting I am using. When I speak to a Toshiba tech they tell me I have a router conflict. To verify this I went to my local Starbucks and low and behold it logged right on with no problem (The Starbucks system was not a protected system). This confirms to me that there is a conflict between the router and the tablet.
View 1 Replies
View Related
Feb 10, 2012
The router will serve as an access point for 10 wireless station, 6 of them will run over Terminal server, the router will also serve 20 computer for the internet, so I want to Link aggregate the four LAN port to my swtich, I know how to do it on my Dell Powerconnect, but I want to know if the WRVS4400N will support it, there will be a lot of traffic going through the router so linking the 4 port in LAG mode to my Powerconnect swicth will speed up the communication
View 1 Replies
View Related
Jul 13, 2011
I cannot connect via VPN PPTP (normal setup in windows xp), I have managed to connect over VPN direct connected to internet, through the router (WRVS4400n) if I turn off the firewall. But I cannot connect with the firewall enabled,One more thing, the device is on and I have enabled the passthrough (and 'Multicast Passthrough' in firewall basic settings) for all available options where one of the options is PPTP.
View 1 Replies
View Related
Oct 6, 2011
i want to set WRVS4400N Route all traffic through
it function as same as sonicwall Route All
[URL]
View 1 Replies
View Related
Mar 12, 2013
I am attempting to setup a router with another vendor, but I am not wanting to give full access to the network just a couple IP addresses, most routers you can setup an VPN IP Range, but I can't find that setting on this Cisco WRVS4400N.
View 1 Replies
View Related
