Linksys Access Point :: WRVS4400N / Cannot Connect Android Tablet
Nov 29, 2011
I just purchased a Toshiba Thrive tablet and I can't get it to connect to my wireless router. My router (WRVS4400N) works flawlessly with my laptop and desktop. I have spoken to a Cisco tech rep and they assured me that there is not a compatibility problem with the WPA-Personal setting I am using. When I speak to a Toshiba tech they tell me I have a router conflict. To verify this I went to my local Starbucks and low and behold it logged right on with no problem (The Starbucks system was not a protected system). This confirms to me that there is a conflict between the router and the tablet.
View 1 Replies
ADVERTISEMENT
Nov 29, 2011
I just purchased a Toshiba Thrive tablet and I can't get it to connect to my wireless router. My router (WRVS4400N) works flawlessly with my laptop and desktop. I have spoken to a Cisco tech rep and they assured me that there is not a compatibility problem with the WPA-Personal setting I am using. When I speak to a Toshiba tech they tell me I have a router conflict. To verify this I went to my local Starbucks and low and behold it logged right on with no problem (The Starbucks system was not a protected system). This confirms to me that there is a conflict between the router and the tablet.Toshiba tells me that it is not compliant with Android but it is with Windows that is why I don't have an issue with the computers.
View 2 Replies
View Related
Feb 16, 2012
I have an Adroid 2.3.1 tablet, a WRT160N router, and an ActionTec M1000 DSL modem. I have many devices, both wired and wireless, connected and all work fine. These include xBox (Port Triggering in place) and 2 laptops via wireless and 3 machines wired.For some reason the Android tablet will not connect. It does connect to other WIFI spots including neighbors, cafes, etc. For this reason I believe the issue is with the router.I have tried all sorts of things including:
Change advanced wireless settings (Beacon Interval, Fragmentation Threshold, RTS Threshold)Tried B, G, B&G, B/G/NTried WEP, WPA, WPA2Tried Channel 1, 6, 11.Reset the router (via reset button, via Factory Defaults option, Reboot, power off 10 secs, back on)Updated router firmware to latestUpdated tablet firmware to latestTried enabling MAC Address filteringAt one time I saw messages in the DHCP log wherein it was trying to register and I noticed the MAC Address doesn't match what the tablet says it has. Now I can't even get that. It says "Connecting", a few seconds then "Disconnected".I am now forced to consider getting a new router. If I can't get this resolved, the new one will not be manufactured by Cisco.
View 5 Replies
View Related
Dec 23, 2012
I just got a maylong 4.0 android tablet. The instuctions are vague on how to set up an internet connection.
View 2 Replies
View Related
Jun 5, 2011
i have purchased a 2.2 android tablet everything works fine apart from internet access tablet scans finds my sky router tap on connect enter password which i have double checked starts to connect then says disconnected and disabled is this a security issue with the router or conflict with the tablet desktop connects great and also wii.
View 1 Replies
View Related
Jan 23, 2012
I'm trying to connect an android tablet (asus transformer) to my ASA5510 ver 8.4(2)I successfully configured to have "PHASE 2 COMPLETED"
But my droid give the message "user or password incorrect" and vpn isn't established.I use local AAA authentification.On the debug, I don't see anything or can't find the appropriate debug. [code]
View 8 Replies
View Related
May 24, 2011
I recently purchased a android tablet and want to access my wireless connection through my network. When the tablet recognizes my network but when I enter my router password it wont accept it. I have reset the router back to default and reset a new password and it still will not accept it.
View 4 Replies
View Related
Jan 4, 2013
I cannot connect my new Filemate Clear android tablet to the internet. No problem connecting laptops. I keep getting this message, authentication problem after trying to connect.
View 1 Replies
View Related
Sep 4, 2012
I setup an accespoint on my laptop. Now I want to connect my Phone (android) to this network but, he is asking for an Ip-address I tried the following;
- give the phone a static ip address
View 2 Replies
View Related
Dec 30, 2012
I cannot connect Android Tablet to home WiFi. Getting Authentication Problem" as error.All other devices connected. Have tried all of the solutions on this and other sites
View 3 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Dec 30, 2012
I cannot connect to home WiFi while all other devices connected. Getthing "Authentication Error"
View 2 Replies
View Related
Feb 17, 2012
is there a java download for android
View 3 Replies
View Related
Mar 20, 2012
My Android Tablet ASUS TF101 fails to wireless connect at the next reboot after it has been sleeping.Unplugging the DIR615 and replugging solves the problem until next time. The Tablet shows a poor signal until the router reboots (even at 4 feet away). The router firmware is 3.11NA and the hardware is C1.Other hardware like an ACER WIN-7 PC can still wireless connect when this problem is exhibited.
View 6 Replies
View Related
Mar 28, 2012
I had bought dlink's dir615 router, plug it to my broadband connection to have Wi-Fi access. My android phone which is HTC Sensation and my sister's phone Samsung Galaxy Mini can detect the wifi and connect/browse to the internet. However when we try to watch online videos (via youtube or other sites) and update/download apps from the google play store its just fails. Is there configurations needed to for my router for the downloads to work?
View 4 Replies
View Related
Sep 30, 2011
The company I work for uses a Cisco ASA 5510 router. We currently have an IPsec VPN set up and useres connect through the Ciso VPN client using group authentication, then they are prompted for a username and password, and use the same username/password they log on to thier work computers with. Some of the users have recently got Samsung Galaxy 10.1 tablets and would like to connect to the VPN using those tablets, but I can't figure out how to get the tablets to work. I've tried the anyconnect app for the andriod market as well as creating a VPN connection from the Tablet's settings page, but no luck either way. Perhaps I'm not entering a setting right? Has any one had any luck getting andriod tablets to connect to a Cisoc VPN?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Aug 16, 2011
What type of download from Java for Acer iconia a599 tab
View 4 Replies
View Related
Mar 25, 2013
I am having an issue with my Android Tablet running 4.1 (Jelly Bean). It is able to the SSID, but when I try to connect - it stays connecting and then says saved, and never connects, as it does not pick up an IP address. I updated the firmware on the Aironet 1140 due to my Windows 8 pc's not connecting as well, it solved my Windows 8 problem, just not my Android Tablet problem. My Ipads do work. Just any android device I connect.
View 1 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
Apr 1, 2012
I have a Samsung Galaxy 10.1 tablet and have bee trying to connect to my WRVS4400N router with VPN through the "on board" software as well as with the Any Connect software from Cisco. I have no issues at the moment using Quick VPN from my laptop.
When using the Any Connect software I receive the following messages:
Security warning: untrusted certificate
AnyConnect cannot verify the identity of <IP address>. Would you like to continue anyway?
- Certificate does not match the server name.
- Certificate is from an untrusted source.
- Certificate is not identified for this purpose
[Accept] [Details] [Cancel]
If I select accept, the following error is received:
"Error: Connection attempt has failed due to server communication errors. Please retry the connection".
I have tried setting up the on board VPN with the Samsug Galaxy but every attempt has resulted in a time-out of the connection.
View 2 Replies
View Related
Oct 7, 2012
Have a Samsung tablet supported by Verizon wireless. I need to connect to my home HP printer, but do not have broadband in the home, Can I connect the printer to a router and access via my tablet?
View 1 Replies
View Related
Jul 25, 2012
I want to configure and WAP610N to work as an Access Point (it was configured by previous administrator some time ago): free hotspot open, LAN secured by password. What makes my last 2 days horrible is that I can't even get access to Administration Panel. Used Cisco Online Support Articles, used User Manual, tried many ways to connect without luck.First of all I've connected LAN cable directly from PC to AP and Windows stuck at "Identyfying State", after some hours "arp -a" command shows me only IP's of my LAN, no MAC of the AP.Tried to reset settings to the factory default - when on push for 30 seconds reset button, power diode blinks, ap starts and settings are the same - still connects to the company's LAN.Wireless networks is default 'linksys' without password I can connect to it and get the internet, after pushing fast connection button it changes to secured "Linksys-<some letters and numbers>" to which I can't connect.I can't even get IP on wired and wireless connection - DHCP don't work? I don't know what IP to set manually. How can I get access to Administration Panel? How to reset this thing?
View 4 Replies
View Related
Feb 19, 2011
My Linksys Range Extender died. So I bought a WAP54G thinking that I could use it as a repeater to extent the range of the signal from my router to the other wireless PCs in the house.
1st floor:
PC1 connected to a WRT54G v.5 router
PC2 connected to PC1 router via USB network adapter
Laptop connected to PC1 royter via internal wireless
2nd floor
PC3 connected to PC1 router via USB network adapter
PC4 connected to PC1 router via USB network adapter
The main goal is to set up the WAP54G in between PC1 and the other PCs to extent the range of the signal particularly to the 2nd floor PCs.The instructions for configuring the WAP54G are fairly straightforward, but the first issue I run into is not being able to connect to the WAP54G web setup. I am using the following instructions:
[url]...
once I configure or setup the WAP54G through another PC as a repeater, will I be able to disconnect it from the PC and use it as a standalone (e.g., plugging only the power in and leaving it in my kitchen or a hallway) to extend the range of the signal? Or does it have to stay connected to PC1 and does PC1 always have to be on for this WAP54G to act as a repeater?
View 2 Replies
View Related
Nov 25, 2011
linksys router WRT120W only connects halfway and then freezes.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Dec 4, 2011
How do I connect three or more WAP54G's in bridge.
View 3 Replies
View Related
Jan 7, 2012
iPhone does not recognize home network. MacBook does! The phone recognizes and connects to all otther networks except this one at home.The WAP610N is used as an extender attached to Alcatel Lucent 7130.
View 2 Replies
View Related
Dec 14, 2012
Even using the static address I cannot connect to the unit's set up page.
View 1 Replies
View Related
Feb 20, 2011
I am unable to connect wirelessly to a WAP54G v2 with a Dell Inspiron 17R/N7010 running Windows 7. In fact, previously a relative's laptop, also running Windows 7, was also unable to connect at my location.The access point has no security enabled. It shows up in the list of available wireless networks. I've configured the wireless adapter properly (static ip). Yet connection fails. Windows suggests that I power cycle the access point and try again. If I use the same configuration for the wired connection, it works. Is there a compatibility issue with Windows 7 and the WAP54G v2?
View 6 Replies
View Related
Dec 9, 2011
I've some strange things with my WAP610.I connect it to my lan, my DHCP server assign an IP, that's normal way..I lookup for this IP, and fill in the address field in my IE (firefox or safari I've tried all of them).... the AP ask me password and user... I fill in the password field... and get into config...
So I think it could be a bug with static IP... I'll try on the wireless security... select "manual"... change nothing (leave default value) click save... wait a while... connect on the DHCP ip, return to the wireless page... and lost a lot of time since nothing is saved.
View 7 Replies
View Related
Oct 12, 2011
1. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
View 3 Replies
View Related
Feb 25, 2011
I have a linksys wrt54g ethernet wired to my router. I got a wap54g and don't know a thing about either. I hooked up the wrt54g years ago with linksys assistance. I thought I could just hook up a wap54g with ethernet to the directv dvr and the two would talk.
View 2 Replies
View Related
