Linksys Wireless Router :: WRVS4400N Firewall Blocking VPN Pass Through
Jul 13, 2011
I cannot connect via VPN PPTP (normal setup in windows xp), I have managed to connect over VPN direct connected to internet, through the router (WRVS4400n) if I turn off the firewall. But I cannot connect with the firewall enabled,One more thing, the device is on and I have enabled the passthrough (and 'Multicast Passthrough' in firewall basic settings) for all available options where one of the options is PPTP.
View 1 Replies
ADVERTISEMENT
Sep 18, 2011
My WRVS4400N is not letting my VPN client through the router. I have checked the passthrough boxes for all 3 protocols. I have port range forwarding for my VPN connections to my SBS2008 box on port 1723.
View 5 Replies
View Related
Sep 22, 2011
Recently i had suffering with wireless connection problem, currently my wireless router connected to WAN directly, after that go into firewall and then go thru switch to end user PC, for LAN user there is no issue, but for wireless connected PC it is prompted with limited connectivity problem(DHCP is disable on router), after check with ipconfig /all. it seem likely due to wireless PC cannot get the IP from DHCP server. i am using DLink615 router. i had checked firewall setting there is firewall policy that connected all router ip into company LAN, but i don't think there is DHCP VPN setting up. is there anyway i can go thru firewall and get IP from DHCP server because if i set up DHCP on router, it cannot pass thru and access to LAN.
View 9 Replies
View Related
May 15, 2012
I need to access a shared folder over a VPN connection. Very simple host network: no Microsoft server, no AD. Just a WRVS4400N router and a peer-to-peer network.
Purchased a second WRVS4400N router to create VPN from SOHO and configured via VPN Setup Wizard.
When at the office, I can map a drive letter to a share on the other computer, as follows
net use f: \192.168.1.111MyShare /User:MYSELF mypass
However, when try same command over VPN, I receive the response:
System error 53 has occurred. The network path was not found.
I also cannot net view the other computer -- same error. However, I can successfully ping 192.168.1.111.
More info:
Routers have latest firmware.
Over VPN I cannot browse network via Windows Explorer (Win7 Network Neighborhood shows only my own PC. In the office I can see the other computer and the NAS appliance "NAS01").
I also cannot connect by entering \192.168.1.111MyShare into Windows Explorer's address bar (although I can do that successfully when at the office), or by choosing Map Network Drive from "Computer".
However, over VPN, I can get into NAS administration via https://192.168.1.3 and I can print to the office TCPIP printer (192.168.1.222)
View 4 Replies
View Related
Dec 30, 2012
Looking to upgrade my old G router to the EA6500. I don't see anything about VPN pass through on the EA6500 or any linksys N router. Is this feature something they no longer include?
View 3 Replies
View Related
Aug 8, 2011
After updating the firmware of my WRVS4400N from V 2.0.1.3 to 2.0.2.1 all traffic was blocked for all machines, even some not included in the list of PCs. As the log was showing that all traffic was blocked by access policies, I disabled the only rule I had (blocking access to some sites to some MAC address list) and everything worked fine.I tried creating a new, simpler rule but after activation it blocked again all traffic for all the LAN.After many trials, I decided to roll back to the previous V2.0.1.3 which solved this problem.
View 1 Replies
View Related
Aug 20, 2011
I have e3000 but in VPN Pass through I don't have ( pppoe pass through )
Just I have is ipsec + pptp + l2tp only
How could i add ppoe pass through in my e3000
View 1 Replies
View Related
Apr 12, 2013
In our area Comcast has increased the internet speed to 50mb. I have a six year old WRT54GL. Can this router pass 50mb through to the computer on a wired connection?
View 5 Replies
View Related
Jun 22, 2007
I set up my daughter's Dell laptop last year to our WRT54G wireless router and I'm trying to connect to our wireless network now with another laptop (a new Dell) and can't find (or remember) my security code or pass phrase. Is there any place on the old laptop that I can access this info? How can I configure the new laptop without this info?
View 9 Replies
View Related
Jul 29, 2011
is there a way i can block a website from being viewed.i would like to do this from the setup page of my e1000 under website restrictions.
View 1 Replies
View Related
Mar 19, 2012
I have a Linksys E2500 wireless router. It seems to be blocking a website (evernote.com). I cannot access this site from any of the computers/ devices in our house, whether they be connected by ethernet or wireless. However, when i move to a different network, I can connect to this site immediately from exactly the devices that do not connect in our house.
How can I determine how/if the router is somehow blocking this site? I have reset the router and upgraded the firmware. Same problem persists. I see nothing in the router settings that would be blocking this site, and I have certainly done nothing intentional in the settings to block this. We used to be able to connect to this with no problems, but all of a sudden, we are blocked.
View 5 Replies
View Related
May 28, 2012
I've had this router for years. I have 2 servers always on, 1 computer with skype, and a 2nd linux machine with ports SSH, bittorrent, and SFTP open. Nearly all the port forwards are assigned to support this.
I got a brand new desktop with lots of CPU/Ram and was using it for development. The network card kept "going out" I would be online and all of a sudden no connections would go out from it.As I tested and diagnosed it I found it still got and held a valid IP, received DNS, but no HTTP or FTP connections would work externally. If I tried to HTTP or FTP to any computer locally on the network it would work fine. But try to access the internet and it was nothing. Restaring the machine would solve it but only for a while, usually run normally for 10-15 minutes then lose network again.. re-installed the drivers, the OS, but the problem remained. I shelfed the unit figuring it was an internal problem with the desktop since it was the only machine.Recently I got a refurbished laptop. to my surprise, it began doing the same thing as soon as I used it! exact same symptoms. So I pulled the old desktop out and it runs completely fine now! the problem has 'transfered' from the desktop to the laptop so I now believe its the router. The router does it to both wired and wireless devices, and seems to target one device at a time to be bitchy to. Allows them to run for a while and then blocks all outgoing port 80/443/21 from that device.
Firmware Version: v2.0.03 Because of DNS issues with the modem the static DNS is transfered directly to my service providers DNS machine NAT enabled, all other advanced routing disabledSPI is onall Internet filters are on, all Web filters are off on FirewallVPN functions disabledAccess Restrictions are offAll Single Port Forwarding slots are directed to 2 machines (which have no problems)No port range triggeringno DMZ or priorities set on QoS
Everything that I know to check for (security, filters, restrictions) are showing errors or something that might cause this. I believe it may be related to the IP expiring, and when the IP renews the router stops permitting its traffic outbound.
View 7 Replies
View Related
Jul 19, 2012
I have 2 WRVS4400N's availible to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies
View Related
Jan 13, 2012
I'm keep failing my pci compliance test I have a wrvs4400n and I keep getting "firewall udp packet source port 53 ruleset bypass" i've blocked port 53 but keep getting rejected. How to set the router?
View 1 Replies
View Related
Feb 26, 2007
I would like to connect to the built in accounts on the wrvs4400n from a mac VPN client. I am new VPN and have not found much information on how to establish this connection. Since Linksys seems determined to rely on Quickvpn, and provides no information on what it is actually doing under the hood I can not figure out how to configure any of the VPN clients available, or the built in VPN tools, for OS X (10.4.8). The only information I have been able to find seems to relate to setting up VPN Tunnels, or running a server behind the wrvs4400n and using one of the VPN passthrough options. I would like to connect directly to the built in accounts, how to set this up on a mac?
View 7 Replies
View Related
Aug 9, 2012
We have a home use WRT160N router linked to a PC desktop and two wireless laptops, Yesterday bought a new I-Phone, but could not link to my network (entered the security key many times). I accidentally connected to computer fix it firm that linked to my PC and wanted a large sum to fix the problem which he said was due to large number of temp?? internet files and once removed he would change the IP address of the desktop computer? Is this diagnosis logical and can I do it on my own. The router is definetely working - both laptops access the internet and I was recently able to hook up a Samsung Blu-Ray player using the same security code I used for the I-Phone.
View 1 Replies
View Related
Aug 14, 2011
There is a way to block access to a website by password protecting it through my linksys router, which is one of thoe wrt54gs. I know I can completely block access of a website and can restrict the viewing hours of facebook at certain times through the router admin IP site but was wondering if it was possible to make it so you have to use a password to view said certain site. If there isn't is there any way maybe through a program or do I have to go through my ISP to see if they can do what I am asking for.
View 1 Replies
View Related
Aug 6, 2011
I cannot connect to my company’s VPN after installing the current firmware (FW_E4200_1.0.02.013_US_20110524) on my E4200 router. Version 1.0.01 was on the router when I received it, and it worked without issues. As soon as I upgraded version 02, I could not initialize a VPN connection. When I try to start a VPN session, I get a "page not found" error when attempting to initiate SSL VPN service using a Microsoft Forefront Unified Access Gateway. VPN pass through is enabled for all protocols in the e4200’s setup. As soon as I revert to firmware 01, everything works fine again.
I did a fresh download and re-flashed the 02 firmware just to make sure that it wasn’t an issue with a bad download or a faulty flash. The problem is consistent and repeatable. I have upgraded and downgraded twice, and the results are exactly the same. My VPN connection works with firmware 01, and it fails with version 02. There is a something different in the 02 firmware that is blocking VPN access.
View 9 Replies
View Related
Feb 5, 2013
I tried to block youtube and facebook https in my router WRT610 V1 but the router fails blocking these websites. But, it does work for blocking youtube and facebook http.
View 9 Replies
View Related
Oct 5, 2012
Device: Linksys E1500 - firmware: 1.0.01? I've got a static IP setup for a small remote office and want to keep tabs on their internet connection by pinging it via a monitoring program we use. However, the router seems to not responding to ICMP.
- Filter Anonymous Internet Requests is unchecked.- I've verified that the Static IP is correct.
- I've tried pinging from several remote locations on different connections, with no avail.
I can't seem to figure out why i can't ping this device. I just want to make sure there isn't a setting in the wireless router that is preventing echo replies.The only other thing i can assume is that Comcast is filtering ICMP on their side of the WAN connection.EDIT: Here's a traceroute from my PC to the WAN side of the Linksys....
Tracing route to 50-194-XXX-XXX-static.hfc.comcastbusiness.net [50.194.XXX.XXX]over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 172.25.2.1 2 6 ms 16 ms 6 ms 10.0.0.5 3 9 ms 8 ms 8 ms 10.0.0.1 4 7 ms 7 ms 7 ms 10.0.0.2 5 8 ms 7 ms 7 ms ont-static-208.57.XXX.XXX.mpowercom.net [208.57.XXX.XXX] 6 7
[code].....
View 3 Replies
View Related
Feb 21, 2013
I bought the EA6500 yesterday, to replace my E3200.Formerly, with the E3200, I was able to block applications on the router admin page, without blocking all internet access, under the "Access Restrictions" Tab. I could create access policies that allowed internet access to specific devices, while blocking port ranges/protocols for specific applicatons. while this didn't work for Skype, which jumps from one port to the other until it finds an open one, it worked perfectly for World of Warcraft. the primary target of my restrictions.in common with the old setup for the E3200, the new cloud login allows me to block internet access completely to a device. it also allows me to block websites to my heart's content, an improvement upon the old system, which stopped at four. but to my great surprise, it will not allow me to specify port blockages for specific apps for specific devices., while the new EA6500 is blessed with the added capability of actually recognizing applications by name, *it is only to give them greater priority*. the Media Prioritization tab lets you give a ton of your bandwith to specific apps, but won't let you throttle or block them. Is there some way to work around this? Some alternative firmware? again, I don't want/need to block all internet access to a particular computer. I only need to block some apps (World of Warcraft, and Skype, possibly some torrents) by closing some ports.
View 2 Replies
View Related
Oct 17, 2011
I have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
View 1 Replies
View Related
Nov 21, 2011
I have a Linksys E2500 Firmware Version: 1.0.03 and am using the "IPSec Passthrough" for work. On a typical day I'll sign in to my work's VPN, do my work, sign off in the evening, and read my personal email with a direct connection to the internet.
Then on the next morning, I am unable to connect to work until I go to http://192.168.1.1/index.asp and click "reboot." And as soon as the modem finishes rebooting, my laptop can connect to work. I've tried this several days in a row now, and indeed all I need to do to get the VPN passthrough working is rebooting the modem.
Nothing under "Applications & Gaming" is set. I've seen some posts about having a trigger on UDP port 500, but I'm not quite sure how to translate it for the E2500. Plus I'd rather the router "just work" day after day for VPN and everything else, like my old router did! Is there some other setting to try or clearer directions for a bulletproof IPSec passthrough on that unit?
View 7 Replies
View Related
Apr 10, 2013
My router,EA4500 is blocking just one I.P address,(a game server), and I am unable to connect to the server. I have tried this on 2 different computers, reinstalled the Cisco Connect software, reset to factory defaults and it is still blocking me from getting on this server. When I by pass the router and plug directly into my modem the Server shows up fine and I am able to get on but when I put the Router back it blocks it and does not show up at all.
View 1 Replies
View Related
Sep 12, 2009
Setting up website blocking. I have set up access restrictions for selected times and days but I also want to set up access restrictions for webistes. Perhaps I'm just not clear on how this is supposed to work - I created a policy called 'Site' and then enter the URL in the website blocking area. The options under the 'Access Restrictions' area are either 'Allow' or 'Deny' - intuitively one would assume the selection should be 'Deny' since this policy is to block access to specific URL's. However, if I click 'Deny' and then save, then the URL's I just entered are cleared. However, if I select 'Allow' then I am essentially giving 24hour access every day to my computers (but blocking the URLs), which then seems to go against the access restrictions I set up for selected times and days. Perhaps these two policies are mutually exclusive but it does not seem clear that it is.
View 2 Replies
View Related
Oct 29, 2011
I am getting 404 messages but the browser is connecting to the site's server (you can see the little icon for each site in the tabs). The two sites I have identified that I cannot access are UIowa libraries and Music from Outer Space.
-I have emptied all cache, cookies, etc.
-I have reset the router to factory defaults and updated the firmware
-I can load both sites from other networks, however two different computers using my router fail to load these two sites.Until a couple days ago I was able to access both of these sites regularly, and I haven't installed anything or changed any settings on my computer.The fact that two different computers cannot load these sites seems to indicate that it is a router problem.
View 3 Replies
View Related
Apr 27, 2012
I would like to automatically check if the VPN is up or down, simple enough, and respond by bumping it, disconnecting and connecting, as needs be (not so simple I think).This through a C# program using HttpWebRequest and HttpWebResponse.It's simple enough to login to the VPN page using known credentials. Done deal. And also very easy to check a couple of known patterns in the VPN table.When I determine I need to bump the VPN, how do we simulate the form submission and/or call to the JavaScript programmatically? we're using a Linksys WRVS4400N router, firmware version V1.1.13.
View 2 Replies
View Related
Feb 26, 2012
I cant get the WRVS4400N to connect to my cable modem. The WAN link light isnt even lighting up. Im wondering if this unit is bad out of the box. Is there a setting im missing to get them to talk to one another. This is no mention in any of the manuals.
Connections: - The "Internet" port on the WRVS4400N to the "Network" port on my cable modem (No link light)
Here is what i have verified at this point: - My old router connects instantly to the modem when plugged in (Same cable) - When i plug my laptop into the WAN port on the WRVS4400N i get a link light. When i plug the modem into the WAN port...nothing.
View 1 Replies
View Related
Jan 24, 2013
I get a "IP address conflict" message on my wireless network. Using a WRVS4400n wireless router with the latest firmware that is set to PPoE. Motorola 336 dsl modem is set to bridge mode. My network has 2 computers attached: hardwire desktop and wireless connection to laptop. When I contacted ATT support, they said the problem is in the wireless modem. Are there some settings in the WRVS4400n that must be set to insure that each computer gets a different IP address?
View 2 Replies
View Related
Nov 8, 2009
I've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's. I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?
View 3 Replies
View Related
Aug 29, 2011
I have a WRVS4400N setup as a main router for one of our bays. For wired connections it is working with no problems. When I first installed it it ran fine for wireless as well. I was trying to get WDS to work and at some point the wireless stopped working. My laptop can no longer connect to it and often cannot see it when doing a scan for networks. I have already checked that it isn't a problem with the laptop, that there are not other networks causing interferance, and even tried resetting to default configs.
View 1 Replies
View Related
Mar 31, 2013
My e4500 seems to be blocking my nhl gamecenter apps from playing live video on Ipad and I phones..nhl support tells me it is setting in router.?
View 6 Replies
View Related
Jan 22, 2012
I just installed the E2500 to replace my older router. With my older router I was able to share files between the different computers in my house. All I did was replace the old router with the new one and now they cant share files? I looked through the router settings and cant find anything showing firewall blocking the file and print sharing. why I cant share the files and how to allow the file sharing?
View 1 Replies
View Related
