I'm keep failing my pci compliance test I have a wrvs4400n and I keep getting "firewall udp packet source port 53 ruleset bypass" i've blocked port 53 but keep getting rejected. How to set the router?
View 1 RepliesI am trying to get our internal network PCI compliant and when I run a network scan from securitymetrics.com I receive the following message about our RV082 router.
Synopsis : The remote service supports the use of weak SSL ciphers. Description : The remote host supports the use of SSL ciphers that offer either weak encryption or no encryption at all. See also :[URL]: Reconfigure the affected application if possible to avoid use of weak ciphers. Risk Factor: Medium / CVSS Base Score : 5.0
I have been googling many different search terms for ssl ciphers, rv082, and pci compliance but didn't see any solutions to this. Any experience with ssl ciphers and how to use more secure ciphers? I just performed a firmware upgrade to 1.3.98-tm in hopes that it would fix this issue.
I have 2 WRVS4400N's availible to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies View RelatedI would like to connect to the built in accounts on the wrvs4400n from a mac VPN client. I am new VPN and have not found much information on how to establish this connection. Since Linksys seems determined to rely on Quickvpn, and provides no information on what it is actually doing under the hood I can not figure out how to configure any of the VPN clients available, or the built in VPN tools, for OS X (10.4.8). The only information I have been able to find seems to relate to setting up VPN Tunnels, or running a server behind the wrvs4400n and using one of the VPN passthrough options. I would like to connect directly to the built in accounts, how to set this up on a mac?
View 7 Replies View RelatedI would like to automatically check if the VPN is up or down, simple enough, and respond by bumping it, disconnecting and connecting, as needs be (not so simple I think).This through a C# program using HttpWebRequest and HttpWebResponse.It's simple enough to login to the VPN page using known credentials. Done deal. And also very easy to check a couple of known patterns in the VPN table.When I determine I need to bump the VPN, how do we simulate the form submission and/or call to the JavaScript programmatically? we're using a Linksys WRVS4400N router, firmware version V1.1.13.
View 2 Replies View RelatedI cant get the WRVS4400N to connect to my cable modem. The WAN link light isnt even lighting up. Im wondering if this unit is bad out of the box. Is there a setting im missing to get them to talk to one another. This is no mention in any of the manuals.
Connections: - The "Internet" port on the WRVS4400N to the "Network" port on my cable modem (No link light)
Here is what i have verified at this point: - My old router connects instantly to the modem when plugged in (Same cable) - When i plug my laptop into the WAN port on the WRVS4400N i get a link light. When i plug the modem into the WAN port...nothing.
I get a "IP address conflict" message on my wireless network. Using a WRVS4400n wireless router with the latest firmware that is set to PPoE. Motorola 336 dsl modem is set to bridge mode. My network has 2 computers attached: hardwire desktop and wireless connection to laptop. When I contacted ATT support, they said the problem is in the wireless modem. Are there some settings in the WRVS4400n that must be set to insure that each computer gets a different IP address?
View 2 Replies View RelatedI've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's. I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?
View 3 Replies View RelatedI have a WRVS4400N setup as a main router for one of our bays. For wired connections it is working with no problems. When I first installed it it ran fine for wireless as well. I was trying to get WDS to work and at some point the wireless stopped working. My laptop can no longer connect to it and often cannot see it when doing a scan for networks. I have already checked that it isn't a problem with the laptop, that there are not other networks causing interferance, and even tried resetting to default configs.
View 1 Replies View RelatedThe router will serve as an access point for 10 wireless station, 6 of them will run over Terminal server, the router will also serve 20 computer for the internet, so I want to Link aggregate the four LAN port to my swtich, I know how to do it on my Dell Powerconnect, but I want to know if the WRVS4400N will support it, there will be a lot of traffic going through the router so linking the 4 port in LAG mode to my Powerconnect swicth will speed up the communication
View 1 Replies View RelatedI cannot connect via VPN PPTP (normal setup in windows xp), I have managed to connect over VPN direct connected to internet, through the router (WRVS4400n) if I turn off the firewall. But I cannot connect with the firewall enabled,One more thing, the device is on and I have enabled the passthrough (and 'Multicast Passthrough' in firewall basic settings) for all available options where one of the options is PPTP.
View 1 Replies View Relatedi want to set WRVS4400N Route all traffic through
it function as same as sonicwall Route All
[URL]
I am attempting to setup a router with another vendor, but I am not wanting to give full access to the network just a couple IP addresses, most routers you can setup an VPN IP Range, but I can't find that setting on this Cisco WRVS4400N.
View 1 Replies View RelatedI bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the QuickVPN Clien for connecting to my home network.My home network is connected to a pre provide by my ISP Thomson and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analysing the log you can see that I can get any PING to complete the VPN connection. [code]
View 1 Replies View RelatedAs a temp work around I have two SSID now, one for everything else running WPA2 and one for xbox running WPA. The xbox seems to not like the router on WPA2 and though this would make one think, oh its your xbox, thats not always the case with devices. Some just may happen to want to use a feature the device doesn't support correctly and other devices are able to work around it while ones not so I cant for sure blame on xbox.
View 1 Replies View Relatedhere comes the incident description: WRVS4400N breaks established VPN session if I am trying to connect to any LAN host via HTTPS.
View 1 Replies View RelatedI've been configured my device to forward FTP service to my server, however, I can't access this service outside from my network. I used Single Port Forward and not worked, after, I've used Port Range Forwarding starting in 20 to 21 and not work again.I've sniffed my computer and I've found just 3 outsides packages without response.I've tried with directly IP ADDR and DYNDNS ADDR, but neither one or other worked.
View 1 Replies View RelatedI have a linksys wrvs4400n router on which:The wireless computers are connected to the home network (v lan 1)Port 1 is connected to the home network (v lan 1)Port 2 is connected to the office network (v lan 2)And the printers are connected to port 3.Now I'd like to setup the router in such a way that all computers have access to the printers (port 3), but I don't know what v lan settings I have to use on port 3, or if it is even possible...
View 5 Replies View RelatedType: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again.
View 1 Replies View RelatedSo I have an WRVS4400N V2 and just got a new laptop with an Intel 6230 Wifi card in it and have an odd problem.While the laptop is on battery power the network gets massive packet loss.
I don't know what to do.Laptop manufacture says its AP but AP worked fine with old laptop and works fine when laptop is on power and all other devices seem to be fine with the exception of my Xbox 360 that wont connect if I have it on WPA2 but I will post another thread for that.
Every day or 2 my VPN times out. It still says "connected", but I cannot connect to anything thru the VPN. Once I disconnect and reconnect it works fine?how I can keep this connected at all times without having to go through this process every day or 2?
View 1 Replies View RelatedI have a new WRVS4400N configured with a site to site VPN to connect to my office. At the office, we're running a Cisco PIX 515E. I have successfully established an IKE preshared key and the tunnel is listed as Up. I can successfully connect through the VPN tunnel into the office network through the tunnel and all seems good. After some period of time, the tunnel apparently goes into a bad state. Access to the office network is no longer available. When looking at the VPN status screen, the Linksys indicates that the tunnel is up. However, I cannot ping any resources on the office lan. If I disconnect and connect the site to site VPN tunnel, it connects and comes back up successfully. It seems like there is some sort of timeout taking place here. I am running the 1.1.03 firmware.
View 7 Replies View RelatedIs the Aironet 1400 bridge FIPS 140-2 compliance? Based on the Release 12.3(8)JA, the Cisco IOS software release 12.3(8)JA is undergoing FIPS 140-2 Level 2 validation. Does it mean it is FIPS 140-2 compliance with this software level to run on Aironet 1400 bridges? [URL]
View 1 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine. Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
View 1 Replies View RelatedDuring our recent VA we were told that the below vulnerabilities are exist in the ACS SSL/TLS Protocol Initialization Vector Implementation Information Disclosure Vulnerability on port 443
SSL Weak Cipher Suites Supported on port 2030
SSL Medium Strength Cipher Suites Supported on port 2030
Using LMS 3.2, I've started learning how to use the compliance templates.is there a regex to ignore case? For instance, if I have the line:
clock timezone est -5 in some configs, and
clock timezone EST -5 in others
is there a way to tell the template that upper case and lower case are acceptable matches?
I am installing a new 5520 with IPS for a client, and they were asking about the PCI compliance of the SSL(WebVPN) being self signed. I am not sure what document to find this information from under the PCI DSS. There was also mention about dual authentication being needed, but without seeing the actual requirements, I am just guessing at it.
What is required for making SSL PCI compliant.
I want to add the command "no logging event link-status" to all switchport mode access ports EXCEPT for the ones with the following switchport access vlans: 4022,4032,4042,4052,4072 & 4082. How do I create a compliance template to do this? LMS 3.2, RME 4.3.1
View 6 Replies View RelatedI am trying to create a very basic template in compliance manager that checks for interfaces that aren't members of specific VLANs. VLAN 10 being one of them. I want to match interfaces assigned to VLAN 20. According to the documentation I have read, the following range statement should work because 10 falls between 3 and 19:
Submode: interface [#.*Ethernet.*#]
- switchport access vlan [#[3-19]#]
With the preceeding statement, however, interfaces assigned to both VLAN 10 and VLAN 20 are matching the rule. With this specific rule (not a range), only interfaces w/VLAN 20 are processed by the template, which is expected. We actually have numerous VLANs that we want to exclude/include. I only mentioned VLANs 10 and 20 for brevity.
working with a trial version of Cisco Prime 1.2. I am looking for a Configuration Compliance tool. I used it in Cisco Works LMS - but I dont see a way to do the same thing with Cisco Prime.
View 1 Replies View RelatedI'm having a hard time getting Compliance Manager to accept a "banner login" command I'm attempting to use on 6500 IOS switches. I've edited the template, tried cut-&-paste, looked for the archive file on the server to directly modify it (without success), among other things. I have this feature functioning correctly on CatOS switches, but can't seem to get it properly set on IOS switches. What's the limit, as far as the template is concerned, on the number of characters with this type of command? Where are the archive configs located on the server; in the "shadow" directory?
View 1 Replies View RelatedI just purchased a WRVS4400N Wireless-N Gigabit Security Router - VPN V2.0 and seem not to work with PPPoE from bluewin.ch ( Swisscom )
View 2 Replies View RelatedI have a customer asking if Cisco supporst CISPR11 - Class B. All Cisco switches appear to support CISPR11 - Class A only. What is the difference? Is Class B supported?
View 0 Replies View Related