I cannot successfully forward ports on this router, I've tried a few things but I can only assume the firmware is bad. I've already looked around for a solution but everyone says they solved it by just getting a different router (which at the moment isn't an option).
View 3 RepliesI had a DI 604 router and I couldn't forward ports, someone told me to buy a new router because my modem (TM602G) doesn't have a built-in router and can't be blocking it so I bought a DIR 601 with wireless and I still have the problem.I don't have any firewalls.
View 19 Replies View RelatedIve been having trouble opening any ports on my windows 7 desktop. I connect wirelessly to my D-link Dir 655. I've tried port forwarding single ports to a static ip, but that didnt work either. I currently have the dmz server enabled and still no ports are open according to this port checker Open Port Check Tool - Test Port Forwarding on Your Router I have the windows firewall service disabled, upnp is enabled on my computer and router, i have spi firewall disabled, qos is disabled, and endpoint tcp/udp filtering on endpoint independent.
View 3 Replies View RelatedI'm trying to open ports 2934 and 2935 UDP on my Linksys E1000 router in order to play Falcon 4: Allied Force multiplayer but it's not working.I've correctly created a static IP, and logged in to the E1000's page. Under "Applications & Gaming", and then under "Port Range Forwarding" I entered values thus:
[code]....
I can't get port forwarding to work, even when I turn off the Windows 7 firewall and AVG anti-virus software I'm running. I entered the IP address of my laptop (with a DHCP reservation) and UDP and TCP port numbers, with Schedule set to Always and Inbound Filter set to Allow All. That should be it, right? However, when I check the ports using PFPortChecker, both the UDP and TCP ports are blocked. I do have a Linksys wireless router daisy-chained to the D-Link router, but I'm not communicating on this computer through the Linksys router and the problem still occurs even when the other router is disconnected, so that doesn't appear to have anything to do with the problem. I just updated to the latest firmware (3.13NA).
View 11 Replies View Relatedhow to forward ports using routers
View 2 Replies View RelatedI went out and upgraded to the E3200 a week or so ago and since then i've been unable to forward any ports. I've tried pretty much everything I can think of: disabling Windows firewall, setting a static IP for my computer, setting a static IP for the router, enabling forwarding in both single and range menus, DMZ etc.Here is a screenshot of the port forwarding page just to confirm that i'm doing nothing wrong:In the above photo you will see that I set the computers static ip to x.1.2 and I later changed it to a value that was within DHCP range as listed on the status page of the router admin gui and it still didn't work.So, what I ask of you guys is if you can think of anything that I must be fundamentally doing wrong in order for this not to work. Could it be that i'm missing some possible drivers or network utilities on the computer i'm trying to forward ports too
View 1 Replies View RelatedI've just bought a Cisco 887m-k9 and I am trying to forward the ports. I have a Polycom HDX H.323 device connected to it with a static IP of 10.10.10.5 (ethernet port 0).Previously I had a consumer grade Linksys router which worked fine (I simply entered ports into the GUI), but I couldn't hardcode LAN port speed so I bought this. I have the list of TCP and UDP ports which are forwarded using the following commands:
ip nat pool Polycom 10.10.10.5 10.10.10.5 netmask 255.255.255.0 type rotary
ip nat inside source static tcp 10.10.10.5 80 88.xxx.xxx.49 80 extendable
ip nat inside source static tcp 10.10.10.5 443 88.xxx.xxx.49 443 extendable
ip nat inside source static tcp 10.10.10.5 1300 88.xxx.xxx.49 1300 extendable
[code]....
Where 88.xx.xx.49 is my static IP, while 77.xx.xx.170 is my default gateway.
Need to port forward certain ports for one computer but need UPnP for 2 different ps3's.These are the parts I have. I have read that the GT704WGB does not have a true bridge mode. I don't want to bias anyone however. How to best use this equipment so that I can port forward ports on my laptop. There are also several laptops, desktop and phones on my network but the 2 ps3's and my laptop are what primarily concern me.
-Actiontec GT704WGB for Verizon DSL (Modem / Router Combo)
-Actiontec Support GT704WGB Wireless DSL Gateway for Verizon High Speed Internet access
Cisco Linksys wrt54gs v4 (Router) currently running Tomato firmware but I can flash dd-wrt back to it in a second.
I am attempting to forward port 25565 on my router, and having some trouble. I've set a static IP address as both 192.168.2.10 and 192.168.2.111, and attempted a dynamic IP address. The port forwarding page via 192.168.2.1 in the browser looks like this, with the Private IP Adress changed to whatever corresponding IP address I have set (checked with cmd /ipconfig).
After testing with multiple online port checking tools, the ports remain closed.
We're trying to get a remote access setup for someone who needs to have access from offsite. To make things easy we set it up with a virtual machine running Windows 7 and RDP. Because the "other end" isn't our computer and we've had some difficulties with people using the Cisco VPN client successfully, we were just going to set up a machine as a RDP Gateway and forward the port through the firewall (WebVPN might be nice, but the plugins only do RDP through v5.x). I've tried this on 8.4-1 and after reinstalling the latest 8.2, and supposedly the NAT works and there is a firewall rule allowing access from the outside to the RD-GW server on HTTPS, but the ASA is still blocking those packets. I've looked at 4 howtos and followed them, trying from the console and from ADSM (and one trashed the whole setup, probably related to the reinstall of 8.2) - [code]
View 4 Replies View RelatedI have a router 1802 with a several vlans with IP 192.168.x.0/24 for each vlan (x, it meaning 1, 2, 3, 4, etc.).Now I need that an IP address outside from my network (this IP it is always the same) to be access to on particular machine that is in a private network (192.168.3.0/24) through a several ports:
25 (TCP,UDP), 80 (TCP,UDP), 554 (TCP,UDP), 2000 (TCP,UDP), 10002 (TCP,UDP), 10000 (TCP,UDP), 3000 (TCP,UDP), 3041 (TCP,UDP)
How can I do it?
Outside PC ---------Internet ----MyRouter -----MyParticularPC
83.240.194.99 193.136.80.1 192.168.3.1
I am trying to forward both TCP and UDP ports 3074 but it looks like I can only have either TCP/3074 or UDP/3074 open one at a time. When I try to enter the UDP/3074 NAT statement, I get "ERROR: NAT unable to reserve ports". [code]
View 4 Replies View RelatedI need to forward some ports for remote desktop and remote outlook which I host on an internal server. I have looked all over the web and got close, but no hints on how to do it in the asa 8.2. there is an 8.3 guide, but it is just different enough to not work. I am new to this device and cli.
View 3 Replies View RelatedHow do I forward ports on the N600 DB F9K1102v3? I have looked through everything. When I go to port forward, I enter the info and have it all down correctly, I click save and once it reloads it isn't there and the port isn't forward.
View 1 Replies View RelatedI am new to the RV180W. I am running the most recent firmware--version 1.0.1.9.
I am having trouble getting FTP to work with my QNAP NAS.
QNAP indicates that I should forward ports 55536-56559 to my NAS. I created a custom service to accomplish this, and then, under port forwarding, I selected the service and forwarded it to the private IP that corresponds with the NAS.
However, the port forwarding configuration only allows me to specify *ONE* internal port. With other routers I have always specified the same private port *RANGE* that corresponds with the public ports that I have opened up.
I'm trying to forward ports for SQL and VNC using these commands in the CLI:
ip nat inside source static tcp 192.168.1.150 5900 interface GigabitEthernet0 5900
ip nat inside source static tcp 192.168.1.150 5800 interface GigabitEthernet0 5800
ip nat inside source static tcp 192.168.1.150 1433 interface GigabitEthernet0 1433
where 192.168.1.150 is my server (that hosts SQL server and that I want to be able to connect to remotely using VNC) and GigabitEthernet0 is my configured WAN interface.
When I try to connect from an external client I get the error: "Failed to connect to server..." Is this a firewall issue? How do I get round it? The 819 is the only router/firewall in my network.
I have an ASA 5505 running 8.4(1), and I'm configuring it with ASDM 6.4(1). The outside interface is configured with a single static address. I have a few services port forwarded sucessfully to three different servers on the inside network.
I need to make a media proxy on a SIP server available to the outside. It requires a large range of forwarded UDP ports for the media channels.
I tried adding a network object NAT rule like the others I'm already using to forward HTTP and RDP. I entered a range of ports for the real port and the mapped port using the syntax 60000-60999. ASDM accepted it, but the NAT rule list displays "Any" in the service column. When I apply the change, I get the following error:
nat (inside,outside) static interface service tcp 60000-60999 60000-60999
^
ERROR: % Invalid input detected at '^' marker.
How do I forward a large range of UDP ports from the outside interface to a single server on my inside network? I'd like to use ASDM, but I can switch to the CLI if that works better.
I need to forward several ports. however it has been complicated by a missing or corrupt default access gateway. [code] I am leaving for quite a while tonight, hoping to come back to a reply I am using a belkin router ( will get model number and stuff later - not sure if its needed ) * and wow cable and internet url...
View 8 Replies View RelatedI have a DSL modem, model AG10W. I can't seem to figure out how to forward ports to xbox. No one seems to have this router/modem. I got it from a company here in town. I don't know much about this type of stuff.
View 1 Replies View RelatedA client is thinking of putting in a srp527w. they get assigned a static ip on the adsl interface (165.228.204.x), and then have been assigned another block(203.39.183.x/29).how can i have it so that i am able to forward individual ports from the external ip's, to selected internal ip's.
View 1 Replies View Relatedi've a cisco asa5505 on adam 6.4 and a dvr i would like to forward the ports 9000 and 85 in order to monitor the dvr from outside?
View 1 Replies View RelatedI have an SMCD3GN which I put into bridge mode a while ago and used it as a modem alongside my Linksys WRT54G router. But the SMC is capable of Wireless N, while the Linksys is only capable of wireless G.So I want to turn my SMC into a router + modem again, but I can't figure out how to do it. I tried resetting to factory defaults by holding the reset button at the back of the unit for 30 seconds but it didn't work.I can get it to work with a wired connection, but when I type ipconfig /all into CMD, it doesn't show any default gateway, so I can't access the router online. I've tried various different IPs like 192.168.1.1, 192.168.0.1, etc., but none of them work.
View 3 Replies View Relatedmy internet has recently been spiking every 10-15 seconds constantly. Wired and wireless both experience the spike. My modem is SMCD3GN-RRR. Heres a ping to google.ca: I've called my ISP and they said everything was fine after they ran some tests. What could be causing this and how can I fix it?
View 5 Replies View RelatedI've been having some problems with my new custom built computer connected wirelessly to my Router. My router is an SMCD3GN. So it is a Router/Modem in one. I am currently using the Linksys AE3000 Wireless-N USB Adapter. I have had a past Wireless USB Adapter, & an internal Wireless network card. The USB quit working & in order for me to get it to work is I have to reinstall the drivers everytime I turn my computer back on. The internal wireless network card would randomly lose internet every 30mins - an hour. Being a gamer, this is very frustrating. So, right now I am using the Linksys USB, and I was just playing a game & talking to some friends on skype & I would lose internet for 2 seconds then it would automatically reconnect. So I am beginning to think that it might be my Router but I tried my USB on my laptop for like 10 mins (I disabled the internal wireless network adapter) & I went into cmd.exe and pinged google for about 10 mins, & it said "Request Timed Out." several times.
View 2 Replies View RelatedRouter 1
Cisco EPC2420
192.168.1.1Connects to ISP via F-connectorConnects to Router 2
Router 2
Asus DSL_N55U
192.168.1.2Connects to 192.168.1.12(Linux Server)
So I bought router 2 but since it doesn't have an F-connector input I need to keep router 1 in the infrastructure so I can connect to the internet.The port forwarding on router 1 is a limited list so I can only add so many rules and would rather have my router 2 do this as it alot better but i cannot seem to get it to work.So I set a rule in router 1 to forward all ports to router 2 and then setup the port forwarding in router 2 to send port 22 to my linux box but it didnt work.
We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies View RelatedIs there a way to associate spare firewall ports with another port that is being used..For example...int gi 0/2 is being used currently for my web dmz. Its ip is 192.168.10.1..Is there a way for me to associate gi 0/3 with the same layer 2 as gi 0/2 ?
In my webdmz I use 2 ACE 4710 proxys in FT mode. I used a layer 2 switch to connect firewall and proxys together.
I would like to eliminate this switch if possible..and connect both 4710's (layer 2) direct to firewall.If I could make gi0/2 - 4 part of the same vlan, then I would be good to go.
How many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies View RelatedOne of techs accidentally connected two access ports from different switches together. Since then, LMS is alerting them as being Link ports down. I tried to default the config and set them to access ports without any success. what I should do in LMS to recognize them as access ports?
View 2 Replies View RelatedI have just purchased a nas drive. I want to be able to access my files from anywhere. I believe if i setup FTP i can view the files over the web. from what i have been told i need to forward port 21 to the ip address of the nas drive.
View 6 Replies View RelatedI'm trying to forward a site (ex: facebook) to another ip address or site (on another computer). Just wondering if it's possible by editing settings in the router (I do not have access to the 2nd computer but it is on the network).
View 5 Replies View RelatedWhat the most cost and time effective way to have an ip request return with another ip address from outside the WAN of the router.Specifically want to have an application request for example 192.168.1.121 and have 173.194.43.41 respond and communicate with the application instead. To make it a bit more interesting I'd like actually to set a table or config file to point to a domain name (url) which gets resolved as an ip address. (Port independent)To get a better understanding:one example might be typing in 192.168.1.121 in a browser and googles search engine comes up on the browser.another example might be typing in 192.168.1.121 in an ftp client and it hooks to an ftp server on the other side of the world which resolves to [URL]. I was looking at openwrt and tomato a little but I don't think I have such a complete grasp on how to do it in general. Being that it seems they are 2 different layers of the network model, I was told it can't be done but I don't know if I can believe that yet. Either by third party software or reprogramming the router or adding another device to the network.
View 3 Replies View Related