I'm trying to forward a site (ex: facebook) to another ip address or site (on another computer). Just wondering if it's possible by editing settings in the router (I do not have access to the 2nd computer but it is on the network).
View 5 RepliesI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies View RelatedI have a ASA 5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.
Secondly request also they need failover over the ISP link.
how we immplement the same on ASA 5510.
We have a scenario where the Cisco ASA 5505 will be one end of a site-to-site VPN. The same ASA 5505 also allows Client VPN connection. The question is around IP pooling. If I assign a pool of IP's (192.168.1.20 - 192.168.1.30) for Client VPN connections - do I need to be sure that those same IP's are not used on the other side of site-to-site VPN ?
There could be PC's/Servers running 192.168.1.0/24 on the other side of site-to-site VPN. Would this cause an address conflict ?
I need configure a VPN site-to-site between two offices (Office A e Office B)The Office A (headquarters) have a Router CIsco 5510 and we have approximately 200 employess?
The Office B (branch) dont have any cisco Router but we will buy one ( is a small office, we have aproximadaly 20)?So I need configure a VPN site-to-site using the IPSec (do this is easy), but i need control the computers in the Office B that can access the Office A.
I Think that I can use a acl using the Mac Address to control, but how can I apply a control access List by Mac Address in the VPN site-to-site that is configured using a IPSec?
Is there other form to control the access of the Office B to Office A? We have a big fear for example, a unknow computer connect in the Office B using any mode off access (Ethernet cable, or Wirelless), and this "unwanted" computer access the Office A.
I need configure a VPN site-to-site between two offices (Office A e Office B) the Office A (headquarters) have a Router CIsco 5510 and we have approximately 200 employess The Office B (branch) dont have any cisco Router but we will buy one ( is a small office, we have aproximadaly 20 guys) So I need configure a VPN site-to-site using the IPSec (do this is easy), but i need control the computers in the Office B that can access the Office A.I Think that I can use a acl using the Mac Address to control, but how can I apply a control access List by Mac Address in the VPN site-to-site that is configured using a IPSec? Is there other form to control the access of the Office B to Office A? We have a big fear for example, a unknow computer connect in the Office B using any mode off access (Ethernet cable, or Wirelless), and this "unwanted" computer access the Office A.
View 5 Replies View RelatedI have a couple of domains and servers. I want to forward my domains to my local IP's. Currently, my domains only forward to my WAN ip and then handled by ports. The problem is that I have a lot of the same applications using the same ports.
How do hosting companies do [URL[ For more clarification, This is kind of what I want to do - Domain.com --> 76.xx.xxx.xx --> 192.168.1.xxx ^My domain^ ^My WAN IP^ ^My LAN IP^
Do I need a DNS server? Do I need a proxy server?
How do you forward a domain to a sub-net address? I know how to forward to my network address, but I have not been able to find any documentation on the internet on how to forward to a LAN address.
View 2 Replies View RelatedI have been asked to "forward a port on an ASA 5505 to an internal ip address." Sounds easy for most of you, and I thought I did it right, but I am not certain. Basically, they want it set up so that when xx.xx.xx.xx:30000 (x's = the firewall ip with port 30000) is accessed from outside, it is forwarded to an internal ip on port 30000 (xxx.xxx.x.xxx:30000)
Here is what I tried from within ASDM 6.4:
1. NAT Rules-add static NAT route:
original-Interface: inside
-Source: xx.xx.xx.xx (local ip of computer on LAN they wish to access from outside)
Translated - Interface - Use Interface IP Address
Enable PAT: Original and Translated port both set to 30000
2. Access Rule - add
Interface: Inside
Source: any
Destination: xx.xx.xx.xx (IP of Firewall)
Service: tcp/30000
I have a cisco asa 5505 and i need a public ip address on the inside of my network without NAT. for example: I can create a static nat translation rule, but this is not what i need.
isp -> x.x.x.1 /29 (outside asa) (inside network) x.x.x.2 /29
Is this possible?
I recently installed a First Alert Security System and assigned IP address to the DVR but within the DHCP (After reading many threads, I will asssign, ping and create a static IP outside of the DHCP, maybe this will resolve the issue). I am able to view the cameras on my iPhone and HP Laptop but only internally on my network. I am trying to port forward my DVR IP address to be able to view the cameras on a public website. Although I am going to chcek and see if assigning an IP to my DVR outside of the DHCP and hopefully this will be it, I am afraid that my CradelPoint CRT 500 Modem will not support it. I read on one thread that this is a common issue after you have exhausted all the options. How can I be sure that my modem supports that my router port forwards? I want to avoid configuring to run in bridged or pass-through mode.
View 3 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 5 Replies View RelatedI'm trying to set up a minecraft server i have the correct ipv4 adress and port but for some reason its still closed?
View 7 Replies View RelatedI have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.
All this box really does is port forward external clients to 1 address on the internal lan for client software updates. Any example configs?
So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2
So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
I have some Ethernet-connected cameras that all have the same Ethernet MAC address FF:FF:FF:0A:0A:0A. They were originally designed to directly connect to a Windows PC, but they can also connect through a simple unmanaged switch.A Catalyst 3560 switch won't forward packets to or from anything with that MAC address, at least not by default. Is there a way to convince the switch to do so?
It was my hope to replace the dedicated connections we have for these cameras with a separate VLAN for each camera, and switch them through our existing switch network. Given that all of the cameras use the same MAC address, putting them on the same network is out of the question, but different VLANs, where the only two devices on each VLAN were the camera and the PC that uses it, would be fine.
The switches run IOS 12.2(55) SE through SE3. I learned the camera MAC address from the PC's ARP table while the camera software runs; it turns out the cameras don't have a full IP stack either and don't even do ICMP.
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
View 4 Replies View Relatedhow to set-up cisco site to site vpn having dynamic ip address on both sides??
View 2 Replies View RelatedIs it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies View Relatedhow to open a site by using static ip address
View 2 Replies View RelatedEvery so often when I type in say url internet cuts out. When I click on IE the internet comes up. As soon as I begin to type w again it cuts out. If I shut down my system and reboot everything works great. I spoke to HP and they said to use disk cleanup. I downloaded malware and did a quick scan. I also used the HP performance and also AVG. Someone else said to check the device manager and make changes to the sleep mode of the my computer. My Computer is a HP-G6. with Windows 7 and IE-9
View 1 Replies View RelatedI have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedWe have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies View RelatedThe scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies View RelatedI have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies View Relatedi have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View RelatedI have an EA4500. I am trying to block a specific site based on keywords in the webpage address. how to get the EA4500 to block sites with based on keywords.
View 1 Replies View Relatedi want configure VPN between backoffice which have ASA5510 firewall with static IP and site which have cisco router 1861 with dynamic IP.
how i can configure the site to site between them?
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View RelatedI have an ASA 5525 and need to configure site to site ipsec vpn to 3 peers. I currently have an existing /28 public address from my ISP that is used by other services.Is there a way to use this existing ip range to configure IPSEC tunnels to 3 peers ?
View 10 Replies View RelatedI configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
Our Headquarter (asa 5510) is running a site to site vpn connection with a Branch office (router 2811). All remote users are accesing the internet through the VPN and also accesing headquarter file servers.I want to know if there is a way for some remote users to be able to use the vpn for accesing the file servers but to access the internet through the branch office. The rest of the remote users will be still accessing the internet through VPN.
View 2 Replies View Related