i want configure VPN between backoffice which have ASA5510 firewall with static IP and site which have cisco router 1861 with dynamic IP.
how i can configure the site to site between them?
I have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
I am having a heck of a time configuring 2 RV180W's to establish an IPSEC VPN tunnel. I have some experience at this with other Cisco products (RV042/082) but I can't get these beasties to cooperate.One RV180W is at a client's office and there are to be 1x RV180W and 1x RV120W located at 2 employee's residences.The office has a Static IP and the homes have dymamic IP.I figured I would config the units in the homes to be initators and connect to the office where the static IP is. This is failing for me so far. Any example (screenshot?) of a config where this is working? The firmware on the RV180W's I am trying to configure first are current.I even tried testing from my office (where I have multiple static IPs available) from RV180W here to RV180W at client's office (static at both ends) and I can't get a tunnel to come up. Obviously I am missing the boat at some point in the setup.
View 1 Replies View RelatedI want to connect two sites through a VPN tunnel, such that each machine can access all others, regardless of which site they're located.
The two sites have a VDSL connexion with dynamic public IP addresses. Unfortunately, our ISP does not offer static IP addresses with VDSL connexions.
I plan to do the following : install two RV 120W routers, one at each site, right after the VDSL modemconfigure the modems in bridge mode, such that the 120Ws get directly the WAN IP address and trafficuse DynDNS to assign domain names (site1.dyndns.org and site2.dyndns.org) to each siteassign different subnets to each site (ie 192.168.1/24 for site 1 and 192.168.2/24 for site 2)configure a VPN tunnel in gateway mode using the FQDN (site.dyndsn.org and site2.dyndns.org) of each site on both routers, with corresponding remote subnets
I have Cisco 877 routers, with ethernet (LAN) and ADSL (external) interfaces. The ADSL interface gets dynamic IP. Is Site to Site VPN with Dynamic IP and Internet Browsing Possible on the Same Router.
View 4 Replies View RelatedI have some sites already connected with ASA 5505 site to site VPN with both end static IP. Normally, all traffic can come across without any problem. Even I used "management-access inside" for both ASA.Now I have a new office with only ADSL pppoe connection. I used easy VPN to connect from Site B:remote dynamic IP site to SiteA:static IP with similar example of this: [URL]
All my 5505 ASA are running 8.4(4)1
Site A - Static IP
Site B - dynamic IP with pppoe connection.
After EasyVPN connected, i do not know how do I remote manangment from site A lan to site B 5505 ASA?
I recently bought two RV042s to create a site to site VPN for a client. I have several of these setups installed at other locations but this is the first version 3 hardware I've used.It seems like the dynamic IP functionality of the VPN setup may not be working correctly. I've verified all settings on each router match and have deleted/recreated the setup several times just to make sure. Here's the logs from the router with a static IP.
Nov 29 06:49:51 2012 VPN Log (g2gips0): deleting connection
Nov 29 06:49:51 2012 VPN Log added connection description (g2gips0)
Nov 29 06:49:51 2012 VPN Log listening for IKE messages
Nov 29 06:49:51 2012 VPN Log forgetting secrets
Nov 29 06:49:51 2012 VPN Log loading secrets from '/etc/ipsec.d/ipsec.secrets'
Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address
Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address
I've tried both dynamic IP + email and dynamic IP + FQDN to authenticate the router using the dynamic IP and both give the same error as above.I did a firmware update hoping to fix PPPoE which seemed to be broken with a Netopia modem in bridge mode so both routers are on the latest firmware, v4.2.1.02.
I've got a problem with establishing VPN site-to site tunnel from client (Cisco 1801/871) with dynamic ip addres. My central site using static address but remote site(s) has dynamic IP, and I don't want using dyndns etc. ... just simple any ip client connecting to central site. It had worked very well with Cisco 1812 which was changed for RV220W. Any other tunnels between two static sites works fine with RV220W.
View 1 Replies View RelatedScenario using ASA V8.4
RemoteLan - Router Dynamic WAN IP ----------- site to site VPN --------------ASA - ASA Lan 192.168.1.0/24
10.1.1.0/24
I am trying to get my head round configuring an ASA with V8.4 code where things have changed especially NAT.In earlier ASA 7/8.x code I belive the crypto map below would have allowed a properly configured remote router to connect irrespective of its WAN IP
I am struggling to get my head round how I achieve the same in ASA V8.4 . I have searched the web and found plenty of examples for earlier code but specificlly am trying to learn about how to achieve it with v8.4
access-list outside_cryptomap_20.1 extended permit ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0
nat (inside) 0 access-list outside_crypto_map_20.1
crypto ipsec transform-set myset esp-des esp-sha-hmac
crypto dynamic-map cisco 1 match address outside_crypto_map_20.1
crypto dynamic-map cisco 1 set transform-set myset
[code]....
Can the ASA 5520's support dynamic IP for site to site VPN
View 1 Replies View RelatedI have a ASA5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.Secondly request also they need failover over the ISP link.how we implement the same on ASA 5510.
View 0 Replies View RelatedWe have two ASA5510's connected to two different ISP's and both able to initiate a site-site IPsec connection to a remote site. Depending on the state of the ISP's either ASA may initiate this VPN.We use Reverse Route Injection into OSPF for VPN clients and it works fine with the route being distributed when a client connects and disappearing when there are no clients.So we thought we'd try it for our site-site VPN's. Unfortunately when we enable Reverse Route Injection the routes are distributed regardless of whether the VPN is up or not, so if one ASA has initiated a VPN it's reverse route is distributed (which is what we want) but the other ASA also distributes a route for it's non-existent VPN. The result is that our gateway routers see two OSPF routes and can't ascertain which route is actually up.
Is there any way to distribute the route using Reverse Route Injection (or any other method) only when a site-site VPN is actually up? For various reasons we can't use BGP or other gateway routing protocols.Our ASA5510 are currently running IOS 8.2(1)
we set up a site-to-site-vpn between a 5505 and a 5510 (both asa8.3.1). We configured both sides using the VPN-Wizard in the ASDM. When we try to ping from the network behind the 5505 (192.168.45.0/24) to any host behind the 5510 (192.168.0.0/24) the tunnel gets established but the ping doesn't get trough. After that we tried to connect via RDP to any host behind the 5510 and it worked well (same with ssh, telnet,vnc etc.). Now we want to map a network-share on a 2008-Server behind the 5510 but it's not working. In the ASDM-Log I see some "denied by inside-access in"-messages for the ports 139 and 445. Isn't it right that the whole traffic in the vpn-tunnel bypasses the acl? Even if we open both ports we can't connect to the network-share?
View 1 Replies View RelatedQuestion on ASA VPN tunnels. I have one ASA 5510 in our corporate office, I have two subnets in our corporate office that are configured in the ASA in a Object group. I have a site to site IPSEC tunnel already up and that has been working. I am trying to set up another site to site IPSEC tunnel to a different location that will need to be setup to access the same two subnets. I'm not sure if this can be setup or not, I think I had a problem with setting up two tunnels that were trying to connect to the same subnet but that was between the same two ASA's. Anyways the new tunnel to a new site is not coming up and I want to make sure it is not the subnet issue. The current working tunnel is between two ASA 5510's, the new tunnel we are trying to build is between the ASA and a Sonicwall firewall.
View 3 Replies View Relatedsample configer ASA 5512-x v.9.1 for VPN site to Site, i use to configure on ASA 5510 V.8.2 but on ver 9.1 i never configure. my is use that i dont know to how to configure nonat. i saw some configration as in the attach file they just to show configure VPN but we did not see nonot on command.
View 2 Replies View RelatedI need to configure a site-to-site VPN using a Cisco 881 router on my end and connecting to an ASA5510 on my suppliers end.Our supplier has configured their end and I do not have access to their configuration.
They told us we have to NAT all inside address' to a single address (192.168.89.1) as this is the only one they will let through their firewall/tunnel.I know how to set up the VPN but not too sure how to set up the NAT part.
My sanatized config is attached. The code I am using to NAT my inside network to the single address 192.168.89.1, and send all traffic accross the VPN tunnel as this address is correct? With the router running this config the VPN tunnel does not connect.
I have an issue with a site-to-site VPN tunnel between a ASA5510 and 887VA. I have two tunnels connected to the ASA and one seems to be affected where by the tunnel is disconnected and brought up around every 20 seconds. The tunnel is re-established instantly but this break in transmission is causing application issues.
View 2 Replies View RelatedI have a setup with a pair off ASA5510 on the central site, and approx 20 sites with ASA5505.A couple off network are configured as site to site tunnels to every remote site.Its very stable, but the last year or so ocassionally one of the tunnels go one-way.Just like one of the nat exeptions suddenly stops working.I can see the remote side transmitting packets, but no answer.Central site is running 8.22, want to upgrade but have to mount more RAM.The only cure i have found is to reboot the central pair off ASA5510, not very popular as all 20 tunnels goes down.
View 1 Replies View RelatedI'm trying to establish site to site VPN between ASA5510 to ASA5520, scenario. [code] our Vendor said to nat the local network to specific ip and use that ip as local pool,here the configuration details [code] i create static nat but its doesn't work for me phase 1 is not up, how to create nat local network to 10.10.10.10.
View 9 Replies View RelatedI am trying to establish a Site-to-Site VPN to our customer. I am using ASA5510 and the customer was using Fortigate 1000A. The problem that we're having was regarding the IKE Phase 2, I think!. Cisco debug information indicates "All IPSec SA proposals found unacceptable!"
View 11 Replies View RelatedI have two sites connected using ASA5510 version 6.4(5)
site A site B
10.8.0.0/20 -- ASA -------internet ------------ASA -- 10.6.0.0/24
From site A, i can vnc, rdp, telenet and ssh to site B, however from site B am not able to rdp, vnc telnet or ssh to site A (i can ping site A devices) guess am missing something in the policy but not sure if its in site A or Site B
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedI setup site to site VPN between C2921 (site A) and ASA 5510 (site B). I am having problems with SA being deleted:
1: I can alwasy initiate VPN connection from Site B to Site A.
2: after VPN tunnel is up and idle for a while, SA is dropped and I lost VPN connection from Site A to Site B.
3: to get the connection back, I have to ping Site A from Site B
4: when the connection is established, it works fine!
I am setting up a VPN between my client and their owner, in order for the owner to access ressources at my clients site.Unfortunatly their owner already has an VPN connection to another site with the same subnet as the one on my clients site.I have setup a policy NAT to translate my clients internal LAN to a "NAT" LAN, and i can ping from my clients LAN to their owners LAN, but their owner can not reach any ressources at my clients LAN.
My client has a ASA5510 with a base license, but their owner has their firewall and routing "leased" or something like that, it actually was their ISP who configured the VPN settings. That means of course that i have very limited (no) access to the other site's firewall and I actually even dont know make and model of it.
And last but not least, the subnet the Owner needs to access is on my clients Core Switch and the ASA has an internal route to it.I have pasted in a interresting parts of the ASA config here below, the displayed subnets are not the real ones . [code]
We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies View RelatedThe scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies View RelatedI have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies View Relatedi have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View RelatedI have some home office setups that have s2s VPNs which terminate on my netscreen SSG5. I am moving off the SSG and onto an ASA5510 but not sure if or how I can make this work? The end users do not have static IPs at this point. I use dyn dns on their home routers to update their DHCP IPs from the providers. If they can't get static IPs how can I specify the peer ID with a DNS name rather than IP address?
View 1 Replies View Relatedhow to set-up cisco site to site vpn having dynamic ip address on both sides??
View 2 Replies View RelatedI'm trying to figure out how to get two 5510 ASA's to establish a Site-to-Site VPN.The version with two static IP's is working perfectly and stable but I haven't figured out how to get a VPN running between a static and a dynamic IP
View 12 Replies View RelatedI am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View Related