Cisco VPN :: ASA 8.4 Fixed IP Site - Site VPN Remote Has Dynamic IP?
Jan 12, 2012
Scenario using ASA V8.4
RemoteLan - Router Dynamic WAN IP ----------- site to site VPN --------------ASA - ASA Lan 192.168.1.0/24
10.1.1.0/24
I am trying to get my head round configuring an ASA with V8.4 code where things have changed especially NAT.In earlier ASA 7/8.x code I belive the crypto map below would have allowed a properly configured remote router to connect irrespective of its WAN IP
I am struggling to get my head round how I achieve the same in ASA V8.4 . I have searched the web and found plenty of examples for earlier code but specificlly am trying to learn about how to achieve it with v8.4
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration... Current configuration : 5425 bytes ! ! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01 ! version 12.4 no service pad
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
I have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
I am having a heck of a time configuring 2 RV180W's to establish an IPSEC VPN tunnel. I have some experience at this with other Cisco products (RV042/082) but I can't get these beasties to cooperate.One RV180W is at a client's office and there are to be 1x RV180W and 1x RV120W located at 2 employee's residences.The office has a Static IP and the homes have dymamic IP.I figured I would config the units in the homes to be initators and connect to the office where the static IP is. This is failing for me so far. Any example (screenshot?) of a config where this is working? The firmware on the RV180W's I am trying to configure first are current.I even tried testing from my office (where I have multiple static IPs available) from RV180W here to RV180W at client's office (static at both ends) and I can't get a tunnel to come up. Obviously I am missing the boat at some point in the setup.
I want to connect two sites through a VPN tunnel, such that each machine can access all others, regardless of which site they're located.
The two sites have a VDSL connexion with dynamic public IP addresses. Unfortunately, our ISP does not offer static IP addresses with VDSL connexions.
I plan to do the following : install two RV 120W routers, one at each site, right after the VDSL modemconfigure the modems in bridge mode, such that the 120Ws get directly the WAN IP address and trafficuse DynDNS to assign domain names (site1.dyndns.org and site2.dyndns.org) to each siteassign different subnets to each site (ie 192.168.1/24 for site 1 and 192.168.2/24 for site 2)configure a VPN tunnel in gateway mode using the FQDN (site.dyndsn.org and site2.dyndns.org) of each site on both routers, with corresponding remote subnets
I have Cisco 877 routers, with ethernet (LAN) and ADSL (external) interfaces. The ADSL interface gets dynamic IP. Is Site to Site VPN with Dynamic IP and Internet Browsing Possible on the Same Router.
I have some sites already connected with ASA 5505 site to site VPN with both end static IP. Normally, all traffic can come across without any problem. Even I used "management-access inside" for both ASA.Now I have a new office with only ADSL pppoe connection. I used easy VPN to connect from Site B:remote dynamic IP site to SiteA:static IP with similar example of this: [URL]
All my 5505 ASA are running 8.4(4)1 Site A - Static IP Site B - dynamic IP with pppoe connection.
After EasyVPN connected, i do not know how do I remote manangment from site A lan to site B 5505 ASA?
I recently bought two RV042s to create a site to site VPN for a client. I have several of these setups installed at other locations but this is the first version 3 hardware I've used.It seems like the dynamic IP functionality of the VPN setup may not be working correctly. I've verified all settings on each router match and have deleted/recreated the setup several times just to make sure. Here's the logs from the router with a static IP.
Nov 29 06:49:51 2012 VPN Log (g2gips0): deleting connection Nov 29 06:49:51 2012 VPN Log added connection description (g2gips0) Nov 29 06:49:51 2012 VPN Log listening for IKE messages Nov 29 06:49:51 2012 VPN Log forgetting secrets Nov 29 06:49:51 2012 VPN Log loading secrets from '/etc/ipsec.d/ipsec.secrets' Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address
I've tried both dynamic IP + email and dynamic IP + FQDN to authenticate the router using the dynamic IP and both give the same error as above.I did a firmware update hoping to fix PPPoE which seemed to be broken with a Netopia modem in bridge mode so both routers are on the latest firmware, v4.2.1.02.
I've got a problem with establishing VPN site-to site tunnel from client (Cisco 1801/871) with dynamic ip addres. My central site using static address but remote site(s) has dynamic IP, and I don't want using dyndns etc. ... just simple any ip client connecting to central site. It had worked very well with Cisco 1812 which was changed for RV220W. Any other tunnels between two static sites works fine with RV220W.
we have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.
Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4
Site A internal: 192.160.x.x External: 55.55.555.201(main)/202(mail) Site B (over site-to-site) is 192.260.x.x External: 66.66.666.54(all)
I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?
I setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access. Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
I am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
I have a ASA 5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.
Secondly request also they need failover over the ISP link.
It's been a long time since I played in Cisco CLI.Using a Cisco 506 Firewall 6.3(4) PDM 1.0?Problem is I created a site to site tunnnel with a vendor and since then our remote VPN does not work. Completely times out so I am sure I broke something in the crypto map or something similar.
Tunnel is policy 10 using access-list 101 Remote VPN is Policy 20
I have a cisco ASA 5510 at the branch here. It terminates about 8 vpn tunnels and also it supports remote access clients. I just have a quick question. Can my remote sub-net group access the other remote access site-site VPN subnet group. If yes then how should i configure it.
I am attempting to configure Radius authentication accross a site-to-site VPN for my ASA 5510-01 for remote access.
ASA5510-1 currently has a live site to site to ASA5510-2.
ASA 5510-1 - 10.192.0.253
ASA 5510-2 - 172.16.102.1
DC - 172.16.102.10
ASA5510-01 can ping the DC and vica versa but is unable to authticate when i perform a test. ASA5510-01 can authenticate to a DC on it;s own LAN but not on the remote LAN that DC sits on.
I have double checked the 'Server Secret Key' and ports as well as various users which all work locallly. ASA5510-02 authenticates to DC with no problems.
Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
Remote-access (vpn-houston) uses 192.168.69.0/24. The main site (houston) uses 10.0.0.0/24 The remote site (lugoff) uses 10.0.1.0/24
At the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG). In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG". None of the SSIDs are "anchored".
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs. This site contains two customers. One customer is the Main customer with the second customer leasing space.
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan). I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500. It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site. This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
For my test, I am starting simple. I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low). I have anchored this test WLAN to that controller. At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site. I am unable to obtain an IP address from the remote site. I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?
We have successfully establish a site-to-site vpn, but we have some difficulties when PPTP users try to access the remote network linked by this tunnel. LAN users can access the remote network without problem, but users who are connected remotly to the lan (PPTP) can't access computer on the remote network. Is there a way to allow PPTP user to access the remote network ? Adding a route ?
I have a site-to-site VPN already established, everything is working as it should. I'm trying to block the remote network from accessing our network since we only need to access theirs. I'm sure this is something very easy to implement with an ACL but I'm not sure where this rule needs to go. The VPN is on ASA 5505.
A user with Easy VPN client connects to a 876 ISR (router A). This router also has a site-to-site VPN to another 876 ISR (router B). What I want to achieve is that the user dials in to router A and can access the network on the remote end of the site-to-site tunnel (router B) In diagram:
user (192.168.18.x) - Easy VPN - Router A (192.168.16.x) - sitetosite - Router B (192.168.17.x)
I have added routes in router B to the 192.168.18.x network with router A as next hop, but I can't reach the other segment.
I'm attempting to configure an for both site-to-site and remote access VPNs. The site-to-site is working fine, however when I connect using the Cisco client, after initial connection and password prompt I get a "not connected" status. The log states that a policy map match could not be found. I have successfully set the unit up for remote access with no site-to-site and ran into another host of issues when adding the site-to-site to the working remote access config, so I started over setting up site-to-site first. I've attempted this through ADSM (hate it) - the current configuration is via CLI. I'm certain I'm just missing a piece or two.
We have a site-site and remote vpn configured in same interface in ASA 5520 ( software version 8.3 ). When Remote vpn users try to connect to computers located on the distant end of site-site VPN, their request failed. I tried No-Nat between remote vpn private IP to the remote site private IP, also stated the same in Split tunneling. I cant find even the tracert, ping also timed out.
On one of our branch locations ASA, I have a L2L VPN setup we are adding wireless to this remote location, and the AP's will talk back to the controller at HQ. The AP's are on the downstream L3 switch, and they have been placed on the mgmt network. It's definitely not ideal to have these AP's on the mgmt network, but for now that is how it is setup.
From HQ (163.122.x.x) I can ping and reach the ASA (10.200.2.1, and the downstream L3 switch 10.200.2.100, but when I ping one of the AP's, I get timeouts and and the following error on the ASA:%ASA-3-305005: No translation group found for icmp src outside:10.205.216.73 dst mgmt:10.200.2.152 (type 8, code 0)
It appears it's a NAT issue on the ASA, but I'm confused on what I need to change. Why can I ping the ASA and the switch from HQ, but not the AP's which reside on the same mgmt network? I don't really need it to NAT, just to pass the connections. I currently only have the following two NAT statements in the configure
I have a situation where I need to have remote users vpn into my ASA 5510 and then turn around and hit a site to site tunnel. Now when I am in our office I can hit the site to site vpn fine. When I am at home and vpn to the asa I can not get to the site to site resources. Do you see where my config is incorrect? result of the command: "show run"
I have a PIX 515 and am working with a Site-to-Site VPN. When I do not specify a filter on the Group Policy I can successfully access the remote network and the remote network can access my local network. However this by itself poses a securty risk for my local servers. I need to be able to access the remote network fully, however only one or two workstations on the remote network need to access mine.
If I add access-list vpn-remote-site extended permit ip host remote-wkstn1 any then only the remote workstation can access my remote network. This gets me a step closer as now only the remote workstation can access my network effectively denying everything else. However, from my local network I can now only access the remote workstation and not all of the other devices. I do not have any control over the remote firewall and would like to make sure it is secured on my end.
