Cisco VPN :: ASA5510 Site-to-Site VPN Same LAN Subnets
Jan 21, 2013
I am setting up a VPN between my client and their owner, in order for the owner to access ressources at my clients site.Unfortunatly their owner already has an VPN connection to another site with the same subnet as the one on my clients site.I have setup a policy NAT to translate my clients internal LAN to a "NAT" LAN, and i can ping from my clients LAN to their owners LAN, but their owner can not reach any ressources at my clients LAN.
My client has a ASA5510 with a base license, but their owner has their firewall and routing "leased" or something like that, it actually was their ISP who configured the VPN settings. That means of course that i have very limited (no) access to the other site's firewall and I actually even dont know make and model of it.
And last but not least, the subnet the Owner needs to access is on my clients Core Switch and the ASA has an internal route to it.I have pasted in a interresting parts of the ASA config here below, the displayed subnets are not the real ones . [code]
View 2 Replies
ADVERTISEMENT
Jan 27, 2012
i want configure VPN between backoffice which have ASA5510 firewall with static IP and site which have cisco router 1861 with dynamic IP.
how i can configure the site to site between them?
View 2 Replies
View Related
Apr 16, 2011
I have a ASA5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.Secondly request also they need failover over the ISP link.how we implement the same on ASA 5510.
View 0 Replies
View Related
Jul 29, 2011
We have two ASA5510's connected to two different ISP's and both able to initiate a site-site IPsec connection to a remote site. Depending on the state of the ISP's either ASA may initiate this VPN.We use Reverse Route Injection into OSPF for VPN clients and it works fine with the route being distributed when a client connects and disappearing when there are no clients.So we thought we'd try it for our site-site VPN's. Unfortunately when we enable Reverse Route Injection the routes are distributed regardless of whether the VPN is up or not, so if one ASA has initiated a VPN it's reverse route is distributed (which is what we want) but the other ASA also distributes a route for it's non-existent VPN. The result is that our gateway routers see two OSPF routes and can't ascertain which route is actually up.
Is there any way to distribute the route using Reverse Route Injection (or any other method) only when a site-site VPN is actually up? For various reasons we can't use BGP or other gateway routing protocols.Our ASA5510 are currently running IOS 8.2(1)
View 2 Replies
View Related
May 9, 2011
we set up a site-to-site-vpn between a 5505 and a 5510 (both asa8.3.1). We configured both sides using the VPN-Wizard in the ASDM. When we try to ping from the network behind the 5505 (192.168.45.0/24) to any host behind the 5510 (192.168.0.0/24) the tunnel gets established but the ping doesn't get trough. After that we tried to connect via RDP to any host behind the 5510 and it worked well (same with ssh, telnet,vnc etc.). Now we want to map a network-share on a 2008-Server behind the 5510 but it's not working. In the ASDM-Log I see some "denied by inside-access in"-messages for the ports 139 and 445. Isn't it right that the whole traffic in the vpn-tunnel bypasses the acl? Even if we open both ports we can't connect to the network-share?
View 1 Replies
View Related
Dec 4, 2012
Question on ASA VPN tunnels. I have one ASA 5510 in our corporate office, I have two subnets in our corporate office that are configured in the ASA in a Object group. I have a site to site IPSEC tunnel already up and that has been working. I am trying to set up another site to site IPSEC tunnel to a different location that will need to be setup to access the same two subnets. I'm not sure if this can be setup or not, I think I had a problem with setting up two tunnels that were trying to connect to the same subnet but that was between the same two ASA's. Anyways the new tunnel to a new site is not coming up and I want to make sure it is not the subnet issue. The current working tunnel is between two ASA 5510's, the new tunnel we are trying to build is between the ASA and a Sonicwall firewall.
View 3 Replies
View Related
Mar 18, 2013
sample configer ASA 5512-x v.9.1 for VPN site to Site, i use to configure on ASA 5510 V.8.2 but on ver 9.1 i never configure. my is use that i dont know to how to configure nonat. i saw some configration as in the attach file they just to show configure VPN but we did not see nonot on command.
View 2 Replies
View Related
Aug 22, 2011
I need to configure a site-to-site VPN using a Cisco 881 router on my end and connecting to an ASA5510 on my suppliers end.Our supplier has configured their end and I do not have access to their configuration.
They told us we have to NAT all inside address' to a single address (192.168.89.1) as this is the only one they will let through their firewall/tunnel.I know how to set up the VPN but not too sure how to set up the NAT part.
My sanatized config is attached. The code I am using to NAT my inside network to the single address 192.168.89.1, and send all traffic accross the VPN tunnel as this address is correct? With the router running this config the VPN tunnel does not connect.
View 2 Replies
View Related
Apr 21, 2013
I have an issue with a site-to-site VPN tunnel between a ASA5510 and 887VA. I have two tunnels connected to the ASA and one seems to be affected where by the tunnel is disconnected and brought up around every 20 seconds. The tunnel is re-established instantly but this break in transmission is causing application issues.
View 2 Replies
View Related
May 15, 2011
I have a setup with a pair off ASA5510 on the central site, and approx 20 sites with ASA5505.A couple off network are configured as site to site tunnels to every remote site.Its very stable, but the last year or so ocassionally one of the tunnels go one-way.Just like one of the nat exeptions suddenly stops working.I can see the remote side transmitting packets, but no answer.Central site is running 8.22, want to upgrade but have to mount more RAM.The only cure i have found is to reboot the central pair off ASA5510, not very popular as all 20 tunnels goes down.
View 1 Replies
View Related
Jul 26, 2011
I'm trying to establish site to site VPN between ASA5510 to ASA5520, scenario. [code] our Vendor said to nat the local network to specific ip and use that ip as local pool,here the configuration details [code] i create static nat but its doesn't work for me phase 1 is not up, how to create nat local network to 10.10.10.10.
View 9 Replies
View Related
Feb 8, 2012
I am trying to establish a Site-to-Site VPN to our customer. I am using ASA5510 and the customer was using Fortigate 1000A. The problem that we're having was regarding the IKE Phase 2, I think!. Cisco debug information indicates "All IPSec SA proposals found unacceptable!"
View 11 Replies
View Related
Sep 4, 2012
I have two sites connected using ASA5510 version 6.4(5)
site A site B
10.8.0.0/20 -- ASA -------internet ------------ASA -- 10.6.0.0/24
From site A, i can vnc, rdp, telenet and ssh to site B, however from site B am not able to rdp, vnc telnet or ssh to site A (i can ping site A devices) guess am missing something in the policy but not sure if its in site A or Site B
View 4 Replies
View Related
Jun 25, 2012
I setup site to site VPN between C2921 (site A) and ASA 5510 (site B). I am having problems with SA being deleted:
1: I can alwasy initiate VPN connection from Site B to Site A.
2: after VPN tunnel is up and idle for a while, SA is dropped and I lost VPN connection from Site A to Site B.
3: to get the connection back, I have to ping Site A from Site B
4: when the connection is established, it works fine!
View 3 Replies
View Related
May 31, 2011
I have some home office setups that have s2s VPNs which terminate on my netscreen SSG5. I am moving off the SSG and onto an ASA5510 but not sure if or how I can make this work? The end users do not have static IPs at this point. I use dyn dns on their home routers to update their DHCP IPs from the providers. If they can't get static IPs how can I specify the peer ID with a DNS name rather than IP address?
View 1 Replies
View Related
May 18, 2012
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies
View Related
Jun 17, 2012
We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies
View Related
Jun 13, 2012
The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
View 1 Replies
View Related
Oct 11, 2011
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies
View Related
Feb 7, 2011
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies
View Related
Mar 6, 2011
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies
View Related
Feb 10, 2013
i have cisco ASA5510 Firewall and configured one site to VPN . i want to configure another s2s vpn in the FW for another Site location.what to in the existing Firewall so that 2 site to site vpn can work.
View 4 Replies
View Related
Mar 22, 2011
I have an @Remote appliance through Ricoh for our copiers. This appliance connects to their site to transfer meter readings and other information. This appliance can't connect to their site to transmit data. Ricoh is telling me the problem is on our firewill. I have assigned the Ricoh appliance a static IP address in our network. Our firewall is a Cisco ASA 5510. I don't have much expereince with logging on the ASA, so I'm not sure what "teardown dynamic TCP translation from inside" means. Is there something that is preventing this IP from contacting the Ricoh site? [code]
View 3 Replies
View Related
Apr 26, 2012
I have an asa 5510 that has many(17)ipsec vpn site tunnels on it. One of the tunnels, one running to a c1900isr at the other end, is experiencing 400 to 500ms latency through it. It does appear to be the tunnel only because there is no latency to the internet. I cleared the tunnel group out and readded it to no effect. isp says everything fine. any other known causes for this
View 2 Replies
View Related
May 13, 2013
We have a Cisco ASA 5510 with:
-version: asa845-k8.bin
-ASDM: asdm-711-52.bin
Interface "Outside" is a PPPOE configuration.We currently have 36 site to site VPN connections up and running through the "Outside" interface. Now when we try to add, via ASDM, a new site to site VPN connection, we can not choose the "Outside" interface. The interface is just not available. All other interfaces are, bot those are inside interfaces.
I tried running ASDM on a different computer (thought that ASDM or java got corrupted perhaps), but the same problem appeared.Now when we "shutdown" the outside interface and "no shutdown" it again, the "Outside" interface is available again when you add a new site to site VPN profile.
Sidenote: if we check the current profile of a succesful running site to site VPN, it say's that it's using an inside interface. But that is, ofcourse, not possible.
View 3 Replies
View Related
Dec 3, 2012
I have two routers on my internal network.
10.10.199.106 is a Cisco ASA5510.
10.10.199.108 is a Sonicwall NSA 3500
The sonicwall handles our site to site VPN tunnels. The Cisco handles our client to site VPN connections.
I have a unit that points to 10.10.199.106 (Cisco) for internet access. All other clients on the network point to 10.10.199.108 (Sonicwall) for internet access.The device in question, a Synology NAS, is using 10.10.199.68 as it's IP address.
I'm trying to hit the web interface on the NAS from a remote site across our VPN tunnel. The IP scheme on the remote end of the VPN tunnel is 192.168.72.0/24.
Going through the VPN, I can hit every object on the network that uses .108 (Sonicwalll) as it's gateway. However, I cannot hit the unit that uses .106 (Cisco) as it's gateway.
I added a route statement (using ASDM) that routes all traffic destined to 192.168.72.0/24 to the Sonicwall so it can send it back down the VPN tunnel. If I'm understanding routing correctly, this should allow responses from NAS destined for 192.168.72.0/24 to go back down the VPN tunnel.
View 4 Replies
View Related
Jul 12, 2012
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies
View Related
Nov 21, 2012
I have an ASA 5525 and need to configure site to site ipsec vpn to 3 peers. I currently have an existing /28 public address from my ISP that is used by other services.Is there a way to use this existing ip range to configure IPSEC tunnels to 3 peers ?
View 10 Replies
View Related
Sep 12, 2011
I configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
View 3 Replies
View Related
May 30, 2013
I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
View 9 Replies
View Related
Mar 6, 2013
Our Headquarter (asa 5510) is running a site to site vpn connection with a Branch office (router 2811). All remote users are accesing the internet through the VPN and also accesing headquarter file servers.I want to know if there is a way for some remote users to be able to use the vpn for accesing the file servers but to access the internet through the branch office. The rest of the remote users will be still accessing the internet through VPN.
View 2 Replies
View Related
Nov 27, 2011
We've just deployed a site-to-site VPN using a 5505 ASA on the client's site and a checkpoint Nokia FW on our site. Everything seems to be fine except that the user's connections to their file shares seem to be intermittently dropping. One minute the connection to the shares is there, next thing it's lost. There is no logic to it because no two users are experiencing issues at the same time, as a matter of fact even on the same PC where a user has access to 3 shares on 3 different servers, one could be showing as connected whereas the other two be dropping. [code]
As you can see the Duplex and Speed are set to auto, I've rectified this since then and I'm keeping a close eye on the output errors, and collisions. However, I'm afraid that this did not rectify the issue and the users are still experiencing intermittent connection dropping to their file shares over the VPN!
View 1 Replies
View Related
Jul 28, 2011
I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
View 5 Replies
View Related
