Port Forward DVR IP Address - View Cameras On Public Website
Jul 12, 2012
I recently installed a First Alert Security System and assigned IP address to the DVR but within the DHCP (After reading many threads, I will asssign, ping and create a static IP outside of the DHCP, maybe this will resolve the issue). I am able to view the cameras on my iPhone and HP Laptop but only internally on my network. I am trying to port forward my DVR IP address to be able to view the cameras on a public website. Although I am going to chcek and see if assigning an IP to my DVR outside of the DHCP and hopefully this will be it, I am afraid that my CradelPoint CRT 500 Modem will not support it. I read on one thread that this is a common issue after you have exhausted all the options. How can I be sure that my modem supports that my router port forwards? I want to avoid configuring to run in bridged or pass-through mode.
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
I have a DVR machine that I've been trying to carry out port forwarding to view cameras from outside the network. It lies on 192.168.1.31. The confusing thing is the ports. The configuration on the DVR lists a device port: 8000 and a http port: 80. I am torn between which port to forward.
I purchased some cameras for my building. I have them set up ok on port 85 but I can't view them remotely until I set up the router to forward the port. I have a charter modem and the E2500 router.
I am trying to setup 4 cameras to view with remote live view. I set up my server with IP addresses of 192.168.1.80 .... 85. The screen has only the option for 1 video channel. I have seen on-line screen shots that have options for channel 1 through 8. I want to assign each camera to a different channel so I will be able to use remote live view to show all 4 cameras at the same time. I can only show one at a time. Do I need a different version than 3.3 or some obscure windows 7 setting?
We are in a planning phase of adding another service to our DMZ. The DMZ has a singe publicly accessible IP. We are running Citrix inside our network externally accessible via w121eb https (443). Another service will be added to the DMZ (Exchange/O365) requiring ADFS & and ADFS proxy also using port 443 as well. Both services (the Citrix secure gateway & ADFS) will have separate subdomains but directed to that same IP, each with its own cert.
Now, I guess the question is: How (if possible) can we forward the public requests to the two services that hit our network on the same port (can't change the port on either), to two separate appliances with their own internal IP's internally?Our current appliance on the DMZ is an ASA 5505. Also could use a PIX
I have one public IP address but multiple local servers that run on the same port. I cannot change the port the clients use to connect to this server, so I can't do a port map in my NAT router. The solution I had in mind, is to filter on source address. If a client from public IP X.X.X.X connects to port Z, I want it to go to internal server 10.10.10.10 and if a client from public IP Y.Y.Y.Y connects to port Z, I want it to go to internal server 10.20.20.20. Is this possible? I'm using an ASA5510 but I could also switch to a 5505 for this.
I setup one location (business retail shopping center) in maryland (using swann dvr/cameras- will switch to qsee) with no internet available.I setup another location (business auto shop) in virginia (using qsee dvr/cameras) with internet through verizon fios.I have internet through cox at home in virginia which I can view cameras remotely only to one location in virginia.
I can access my cameras through the Dlink web site (mydlink), but cannot access all of them through D-View Cam o n my desktop. I do a camera search and it only finds two of them and the third one it doesn't see. I tried to insert it manually and it still doesn't see it. It sees it fine in mydlink.
I've uninstalled the D-View Cam program and re-installed it, with the same results.
I have been asked to "forward a port on an ASA 5505 to an internal ip address." Sounds easy for most of you, and I thought I did it right, but I am not certain. Basically, they want it set up so that when xx.xx.xx.xx:30000 (x's = the firewall ip with port 30000) is accessed from outside, it is forwarded to an internal ip on port 30000 (xxx.xxx.x.xxx:30000)
Here is what I tried from within ASDM 6.4:
1. NAT Rules-add static NAT route: original-Interface: inside -Source: xx.xx.xx.xx (local ip of computer on LAN they wish to access from outside)
Translated - Interface - Use Interface IP Address
Enable PAT: Original and Translated port both set to 30000
2. Access Rule - add Interface: Inside Source: any Destination: xx.xx.xx.xx (IP of Firewall) Service: tcp/30000
I need viewing a DVR camera system remotely through a Motorola Netopia 3347 router. I was able to view the system properly for a year with the old ATT modem and a separate router, but recently the modem crashed and ATT replaced it with this Netopia that I can't for the life of me, understand.I can view locally but not remotely from the internet. I need establishing the Pinholes properly. I'm trying to get it working for port 85 for the DVR system. But I'm confused on the Internal vs. External port #'s it asks for in the Pinhole screen. No combination I enter seems to work. I even tried just using port 80 to get it working, but there was a conflict creating a pinhole for 80 since its already mapped to HTTP.
I have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.
All this box really does is port forward external clients to 1 address on the internal lan for client software updates. Any example configs?
So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2
So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
I volunteer at a school who just purchased two 48 port SGE2010 managed switches. I am not a big fan of the web gui and was hoping to see the standard Cisco command prompt instead of the menu-type interface.
Is there a way to view the MAC table showing which MAC address is plugged into which port on the switch? I have been fighting with the menu and the gui for a while now and do not see this anywhere.
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
We have 2 TS (Terminal Servers) and have configured the 1st RDP using my public address (say 8.8.8.8) on port 3389. it is working very well of course. However I need setup my 2nd TS but will use port 7777 on the same public address which is not working.I am using ASDM 6.3 and firmware 8.3.1.Is this a limitation for this IOS?
A website that I usually go to has all of a sudden stopped working for me. It is hackforums.net which I know is up because I have been on it outside of my home network. Every computer on my network will not allow me to go on hackforums.net . I have not added it to a firewall or anything. I have even set my router back to factory default and it still won't let me view hackforums.net from inside my network.
I recently changed webhosting partners for my company's website. With the Change I can view my company's website from inside the LAN but can outside of the LAN.
We have in host webserver that hosts several website, Outside our network i can view each and everyone of them just fine. However inside our network I can't view any of them. I'm able to ping each site by both ip and by name. I just can't displayed them. I've loked into the DNS and everything seems fine there. We tried hard coding the sites into our host files but we still can't pull them up.
I'm trying to get my crappy desktop (with Windows XP) to be a web server. When I go to localhost it displays the website just fine, but when I go to the external IP on another computer it displays "mikrotik routeros 4.11 configuration page". I've forwarded port 80 and disabled my firewall.
Port forwarding (not sure if I did it right) [URL] microtik page that is displayed [URL]
I have a DIR655 and I used to get to see my website from within my network. After a recent crash, I can now only see my website from outside my network.
I'm going to list out my problem, to make it faster to understand.1] My domain name is registered with a company, X.2] My webhosting is hosted by another company, Y.3] My web developer, Mr. Z is trying to do his bit and upload my website.Here's what happens:Mr. Z tells me that he's not able to upload my website and is getting the error "Connection timed out" and "Could not connect to server" on his FileZilla or something. He also tells me that there is a problem with my domain registry.Now, Company Y tells me that the domain name's A-records has to be pointed to the correct IP address [which is, of course, the webhosting IP I bought.]Company X tells me to login to my account and add an A-record pointing it to the correct IP address. I did that.But still Mr. Z tells me he's getting the same error and is not able to connect to the domain name.Now, when I ping my website on MS command prompt, I get a "Request timed out" error.
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
I can't connect to the public weater site NOAA.gov, and weather.gov, but have no problem connecting to any other sites, private of public.WRT54Gv6 wireless with v1.02.08 (Oct 5, 2009) firmware..the latest.3 devices, desktop, laptop, and iPad......none of which can connect to NOAA or weather.gov Government websites are up when I tried to connect.I've connected to these sites for years, and as recently as yesterday.Linksys BEFCMU10 cable modem. This blows my mind, since the 3 device all have different OS's, browsers, AV software. The only thing in common in the network is the modem and wireless router. Why only the two .gov sites cannot connect?
Region : Italy Model : TD-W8968 Hardware Version : V1 Firmwae Version : latest ISP : telecom italia business on ipatm
How to Forward an external wan port like 49150 to lan ip on port 22?In the control pannel I can set only one port , and this port will be the same where the connection will be router to the lan ip ,therefore If I set the port 22 , the connection will be natted to the 22, but how to set a different external port to a specified different lan ip port?
I have one server 172.16.0.100 and i nat this server to a public ip X.X.X.5 and i open RDP for this public ip.Now when i access Remote desktop on this public ip x.x.x.5 it open perfectly.Now my senario is that i want to open a http url on port 5555,server ADMIN open port 80 for this URL on LOCAL lan(http://172.16.0.100:80)So how can i map port 5555 to port 80 on ASA 5520.so when i hit URL [URL]
I have only recently noticed a HUGE decrease in my Utorrent speeds, so i thought i would have a gander and lo and behold.apparently the port Utorrent uses wasn't open. Now, i have tried about 10 different port numbers, made sure Utorrent is being accepted by Norton 360 Firewall,followed complicated directions to (i think) foward ports, and also follow directions to open a specific port.Nothing has worked so far, Utorrent still comes back with a port closed error.
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I'm trying to forward a site (ex: facebook) to another ip address or site (on another computer). Just wondering if it's possible by editing settings in the router (I do not have access to the 2nd computer but it is on the network).
