Cisco Switches :: SGE2010 - How To View Table Showing Which MAC Address Is Plugged Into Which Port On Switch
Jul 31, 2011
I volunteer at a school who just purchased two 48 port SGE2010 managed switches. I am not a big fan of the web gui and was hoping to see the standard Cisco command prompt instead of the menu-type interface.
Is there a way to view the MAC table showing which MAC address is plugged into which port on the switch? I have been fighting with the menu and the gui for a while now and do not see this anywhere.
View 5 Replies
ADVERTISEMENT
Apr 8, 2013
we have 6500 cisco switch as a backbone switch in universty. When ı want to look mac addres table , it does no show all mac address.ı mean if ı type ;show mac address-table there are not all mac address.
View 3 Replies
View Related
Aug 20, 2012
I have 2 switch groups.
2 SGE2010's with VLAN's defined as 10,20 and 30
Vlan 10 is the management VLAN, and it uplinks to our border router.Vlan 20 is the workstation VLAN, and all workstations point to the switch as their default GW? Vlan 30 is the ip phone VLAN, and all phones use this as their gateway.
I would like to put a LAG between said switches, we have some servers on the ip phone switch that need to be accessed by the workstation clients, and the single 100mb link through the router is probably not going to be enough.As I understand it, because the switches have different networks on them, a simple lag will not work. I did create a lag, and assign ip addresses to each side, however in that mode, it doesn't appear I can block vlan 10 from transiting the LAG, and with out that block I will end up with a logical loop, and spanning-tree will block one of the uplinks, or the LAG itself.
View 10 Replies
View Related
May 20, 2013
I want to know how am i do to change the Vlan1`s IP address because the actual ip will be used in another vlan. Actually i haver 10 vlans in L3 mode (routing) implemented in it.
View 5 Replies
View Related
Oct 20, 2012
what is the process of updating firmware on a SGE2010.
I would usually use TFTP - but, I can't see the TFTP command on these SGE2010's
View 1 Replies
View Related
Oct 25, 2012
I have been told there is a limit (8) on the number of source ports that can be mirrored to a given destination port. I can find no specifications or other documentation to corroborate this claim. Any factual data to confirm or refute this claim?
View 7 Replies
View Related
Dec 14, 2011
I have currently a Dell powerconnect 6248 switch combined with a netgear UTM router. I have a basic understanding on how things should work but I don't have the knowledge to apply it as I'm new to setting up vlan and the person before me did the basic configuration like this:
defined 5 VLAN in the netgear router
defined the same 5 VLAN in the dell 6248
connected the dell switch to the netgear router via a trunk port.
Right now all the inter vlan traffic pass thru the netgear router as the dell switch as a trunk port connected to the netgear box who then give dhcp and set himself as the default inter vlan route. I would like to stop that since I would like the cisco switch to handle all the vlan routing for both switch and those switch to send their dhcp request to my win2k8 server.
I did set the sge2010 in layer 3 mode from the small business telnet interface. I then setup the same 5 vlan in the cisco switch.
If I understand this well I need to define an IP address for each vlan interface on the cisco switch for it to be able to route things, I have set them all as x.x.x.3 (x.x1.3 vlan 1, x.x.2.3 vlan2, etc) Then I need both swtich to forward all dhcp request to my dhcp box wich is in vlan 2. My DHCP server will have 5 range of IP address to hand out. my server are connected directly to the dell switch on vlan 2. I have set up a port in the dell switch in trunk mode and did the same thing in the cisco switch and connected them togheter to send all vlan packet. The current setup doesn't work so I need to finalize that setup so that everything works.
View 1 Replies
View Related
Jan 31, 2013
how can i view the port G27 and G28 in GUI? As based on the GUI Adminstrator - > Port Management - > Port Setting i only can view from port G1 to G26. Or it will only appear when the port is active for stacking.
View 3 Replies
View Related
Jul 12, 2012
I recently installed a First Alert Security System and assigned IP address to the DVR but within the DHCP (After reading many threads, I will asssign, ping and create a static IP outside of the DHCP, maybe this will resolve the issue). I am able to view the cameras on my iPhone and HP Laptop but only internally on my network. I am trying to port forward my DVR IP address to be able to view the cameras on a public website. Although I am going to chcek and see if assigning an IP to my DVR outside of the DHCP and hopefully this will be it, I am afraid that my CradelPoint CRT 500 Modem will not support it. I read on one thread that this is a common issue after you have exhausted all the options. How can I be sure that my modem supports that my router port forwards? I want to avoid configuring to run in bridged or pass-through mode.
View 3 Replies
View Related
Jul 12, 2012
I am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:
Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address 192.168.1.254 (and I have tried to use the last IP in the range set by the router 169.254.154.254, to no avail)
How to regaining control of this supposedly smart switch?
View 3 Replies
View Related
Jun 22, 2012
I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies
View Related
Jun 12, 2011
How do I port forward on a SAGEMCOM SE567 router to be able to view my DVR from a remote location?
View 3 Replies
View Related
Nov 3, 2011
I recently ordered and received Cisco Catalyst 3560-CG Series 8-port PoE switches (ws-C3560CG-8PC-S). In running the Cisco Network Assistant (Version 5.6(3)) they show up as an unsupported device. The documentation for this product indicates that you can use CNA to configure this switch. Is there a download or patch available to correct this problem?
View 8 Replies
View Related
Feb 15, 2012
I looking to buy SGE 2010 swith, but I have some question:
1. Can I use 4 SFP ports and stack of two switches at the same time.
2. Is it possible to use for stacking ports other than 24, 48?
3. What is maximum possible number of ports to use for stacking (can I get more than 1Gb thruput).
View 0 Replies
View Related
May 30, 2013
We have a cisco 3750-48 port switch.We have a few SVI's configured and some static routes configured.I had created a new interface vlan and gave it an IP. I can ping the gateway.
Now I want to add a static route to go out that interface.when I add: ip route 10.x.x.x 255.255.255.0 10.52.10.1
it eccepts it (no errors) But, it does not show in the routing table nor in the config? How to add the static route to go out that vlan interface.
View 15 Replies
View Related
Oct 31, 2012
I currently have two SGE2010's with a 4-port LAG configured between them. I'm looking to add another two SGE2010's and I want to add redundancy at the same time. The switches are currently in standalone mode. I don't have fiber connectors and was planning on just using copper for the uplinks.
My questions are:
- Is it possible to use stack mode in conjunction with 4-port LAG groups to create redundant 4-port links between all of the switches? The documentation says that ports 24&48 are reserved for stacking - does that mean I can't specify a LAG instead?
- If 4-port LAGs aren't possible, does that mean that these switches max out at 1Gpbs uplinks if you use stack mode?
View 4 Replies
View Related
Jan 16, 2011
is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies
View Related
Oct 29, 2011
I just purchased an E4200 router. I have four clients on my network and they are all set up for DHCP. I renewed their IPs and they all are connected. "Cisco Connect" reports that I have four clients connected. When I access the router and bring up the DHCP Client Table, there are no entries. There should be four entries. Aftern I enable the logging function, none of the logs have any data in them even after I wait for 45 minutes and use the internet and renew IPs. I am using Firmware Version: 1.0.03. I have the same results for both Chrome and Firefox. I want to be able to set Static IPs but I am hampered by the not having any clients in the DHCP client table.
View 9 Replies
View Related
Sep 10, 2012
Trying to create a wi fi zone in my apartment from my Virgin cable installation. Following their instructions on how to do this I can't succeed as the "view available Wireless networks" option does not appear on Windows XP
View 1 Replies
View Related
May 18, 2011
I am having trouble viewing all the Administration logs in ACS View. I have my Local Log Target set to a Maximum log retention period of 90 days. In ACS View I can display authentications that go back 90 days + However when I try and display the "ACS_Configuration_Audit" in View and perform a Custom query that goes back 90 days it will only display about 35 days of Admin logs.I know the logs are there because when I go into CLI and do a search like "show logging | i "ObjectType=Administrator Account" the Administration logs go back over a year.why ACS View cannot display all the Admin logs?The ACS is running v5.1.0.44 Patch 6 (Also experiencing this in a v5.2 ACS as well)
View 2 Replies
View Related
Aug 30, 2011
I am working on two SGE 2010 stacked and in routing mode. Everything work fine but before finishing the job, I wanted to lockdown all the network device so they would not be accessible from some subnets. Problem is, I cannot bind my ACLs to any interface. I get "Cannot apply because lack of HW resources." I am running firmware 3.0.0.18, and 3.0.1 release notes don't address that issue. TCAM utilization is at 3% Routing resources shows host: 200, routes:60, ip interfaces: 50 I have tried from the cli and get the same message.
View 3 Replies
View Related
Jun 28, 2012
Can I create lag betwen stack unit to increase speed between units ?? stack connection is only 1Gbit on ports 24/48 if posible lag link must be in trunk mode ?
View 4 Replies
View Related
Aug 29, 2011
Is there any issues with accessing the browser based GUI using Windows 7 64bit on a SGE2010 switch? I took the switch home and tried on my XP 32bit machine and works fine, but no luck on any windows 7 64bit pc's. I have tried 3 different new pc's on this new switch and no luck at all.
View 2 Replies
View Related
May 28, 2013
We have a single SGE2010 in layer 3 mode switch with a Server 2008 DHCP server.
We will be implimenting a Voip netowork where the PC's connect to the voip phone. I would like to create another vlan - 10. I have created the vlan and assigned the IP on the swtich.
Routing seems to be working. I can ping both IP addresses of the switch on either vlan.
I cannot get DHCP working. In the SGE switch I have enabled DHCP Relay, enabled option 82, set my DHCP Interface as VLan1, and specified the DHCP servers IP address. On the ports I have set the port where the DHCP server connects to as a trunk port with Vlan 1 untagged and vlan 10 tagged. I have set the ports where the phones connect as a trunk port with vlan1 untagged and vlan 10 tagged.
View 1 Replies
View Related
Apr 16, 2012
There 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it:
TNSWACCS04A1#sh power inline fa1/0/13
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Fa1/0/13 auto on 5.0 IP Phone 7911 2 15.4
[code]....
Switch is Catalyst 3750 with IOS version 12.2(58)SE1
View 4 Replies
View Related
Jan 10, 2011
I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies
View Related
Oct 6, 2011
Have installed a TP-Link TL-WN722N wireless USB adapter.O/Sis Win XP SP3.Np options are showing for Wireless networks under Network Connections.Wireless Zero Conifguration is on.When I run a QSS app I can see neighbours network but not my own (My equipment doesn't support QSS) so the card and driver are working.
View 7 Replies
View Related
Jul 1, 2011
We've have a 2 SGE2010-48 port, stacked. 4 LAGS are denifed, two on primary, whitch are working, two on slave unit are NOT working. Devices connected to LAGS are de the same and same configuration (Cisco ASA 5510).
View 3 Replies
View Related
May 15, 2011
I have been trying, so far unsucessfully, to trigger backups to a TFTP server of our SGE201 switches. I have testesd TFTP backups via the web interface, and that does work. I need SNMP as I need a scriptable method to trgiger the backups on a regular schedule. I am running the SNMP query from a RedHat Linux server. So far I have the following query work out, but it is failing: [code] The error I am getting is generic, and the same query failed on multiple switches running Software Version 3.0.0.18. The switch is set with the community having full SNMP-admin access from the server's IP address.
View 3 Replies
View Related
Mar 7, 2013
I have 5 VLAN's setup in the sge2010. I have one port (uplink for the network) that I want everyone to see. But have separate VLAN's for different departments as to keep them all separate. Everytime i try and Untag that uplink port, i lose my untag in the original VLAN it was tagged in, and it changes to excluded.
View 13 Replies
View Related
Jul 28, 2011
We are experiencing bridge storms and network slow downs and we believe we have traced the issue down to users plugging a cat 5/6 cable between 2 ports on the wall both wired back to a SGE2010 switch.
So we did a test - we plugged a single short cat 6 cable between 2 ports on a SGE2010, our access switch. Suprisingly, even with STP enabled, the switch DID NOT block one of the ports and in a few minutes the ENTIRE NETWORK was down, as CDP, STP, and ARP traffic became a multi-gigabit storm throughout the network.
Why on earth does this switch not block a port that is obviosly looped?
Every other cisco switch since I started on 1900XL's did this in 1999.
View 1 Replies
View Related
May 29, 2013
I am currently running two SGE2010 in stack and planning to purchase new Sg500 .I have two questions :
1. If these two different products can be managed as one stack.
2. Are the SFP (mini-GBIC) connections compatible and if so what accessories or parts do we need to enable them?
View 1 Replies
View Related
Dec 10, 2012
Id like to set up our AP to push our different vlans depending on which ESSID you connect to.
A few things I am unclear on. The switch port on the SGE needs to be in trunk mode I assume.
Do I marry the Management Vlan ID on the AP to the PVID on the SGE port ? Or is the PVID the untagged vlan ID ?
I set the switches port to trunk mode, it's PVID to 10 and set the management vlan ID on the AP to 10 and I get TTL Exceeded in Route when I try to ping.
View 1 Replies
View Related
