Cisco Switches :: Updating Firmware SGE2010 Switch
Oct 20, 2012what is the process of updating firmware on a SGE2010.
I would usually use TFTP - but, I can't see the TFTP command on these SGE2010's
ADVERTISEMENT
Cisco Switches :: SGE2010 - Firmware Upgrade And Configuration Not Saving?
Oct 7, 2012Using the SGE 2010 for Microsoft NAP with 802.1x auth for switch access, which led to a few issues
What i have: An SGE 2010 48 port switch, firmware 3.0.0.17 Firmware upgrade: In order to ensure im not having problems due to old firmware, i tried to upgrade using ros_ls1_bp_ge_bx-3020.ros in order to move to 3.0.2, when uploading the file via TFTP, the upload completes and thats it, nothing happens.Restarting the device: As part of the upgrade process, i thought i might of had to reboot, so i rebooted, and found that all my settings were wiped clean, as if a factory reset had been performed.... and add further to pain, the backup of settings that i had taken do not seem to want to re-apply.NAP support: So i have tested my NPS (radius) server with NTRadping.exe and all is good, however i cannot get the SGE2010 to talk to it.... the authenticator state in the web interface is always listed as initialising.... im not sure if this is a simple incompatibility (hence the attempt at a firmware upgrade), a tag that needs to be set on the radius side or a switch misconfig.
1) how on earth do you upgrade the firmware?
2) why are none of my settings being saved when the device reboots ?
Cisco Switches :: Set Up SGE2010 Combined With Dell 6248 Switch?
Dec 14, 2011I have currently a Dell powerconnect 6248 switch combined with a netgear UTM router. I have a basic understanding on how things should work but I don't have the knowledge to apply it as I'm new to setting up vlan and the person before me did the basic configuration like this:
defined 5 VLAN in the netgear router
defined the same 5 VLAN in the dell 6248
connected the dell switch to the netgear router via a trunk port.
Right now all the inter vlan traffic pass thru the netgear router as the dell switch as a trunk port connected to the netgear box who then give dhcp and set himself as the default inter vlan route. I would like to stop that since I would like the cisco switch to handle all the vlan routing for both switch and those switch to send their dhcp request to my win2k8 server.
I did set the sge2010 in layer 3 mode from the small business telnet interface. I then setup the same 5 vlan in the cisco switch.
If I understand this well I need to define an IP address for each vlan interface on the cisco switch for it to be able to route things, I have set them all as x.x.x.3 (x.x1.3 vlan 1, x.x.2.3 vlan2, etc) Then I need both swtich to forward all dhcp request to my dhcp box wich is in vlan 2. My DHCP server will have 5 range of IP address to hand out. my server are connected directly to the dell switch on vlan 2. I have set up a port in the dell switch in trunk mode and did the same thing in the cisco switch and connected them togheter to send all vlan packet. The current setup doesn't work so I need to finalize that setup so that everything works.
Cisco Switches :: SGE2010 - How To View Table Showing Which MAC Address Is Plugged Into Which Port On Switch
Jul 31, 2011I volunteer at a school who just purchased two 48 port SGE2010 managed switches. I am not a big fan of the web gui and was hoping to see the standard Cisco command prompt instead of the menu-type interface.
Is there a way to view the MAC table showing which MAC address is plugged into which port on the switch? I have been fighting with the menu and the gui for a while now and do not see this anywhere.
Cisco Switches :: SGE2010 Switches / VLANs And A Blocked Port In Spanning-tree?
Aug 20, 2012I have 2 switch groups.
2 SGE2010's with VLAN's defined as 10,20 and 30
Vlan 10 is the management VLAN, and it uplinks to our border router.Vlan 20 is the workstation VLAN, and all workstations point to the switch as their default GW? Vlan 30 is the ip phone VLAN, and all phones use this as their gateway.
I would like to put a LAG between said switches, we have some servers on the ip phone switch that need to be accessed by the workstation clients, and the single 100mb link through the router is probably not going to be enough.As I understand it, because the switches have different networks on them, a simple lag will not work. I did create a lag, and assign ip addresses to each side, however in that mode, it doesn't appear I can block vlan 10 from transiting the LAG, and with out that block I will end up with a logical loop, and spanning-tree will block one of the uplinks, or the LAG itself.
Cisco Switches :: SGE2010 Can Use 4 SFP Ports And Stack Of Two Switches At Same Time
Feb 15, 2012I looking to buy SGE 2010 swith, but I have some question:
1. Can I use 4 SFP ports and stack of two switches at the same time.
2. Is it possible to use for stacking ports other than 24, 48?
3. What is maximum possible number of ports to use for stacking (can I get more than 1Gb thruput).
Cisco Switches :: SGE2010 Switches - Best Way To Implement Redundancy
Oct 31, 2012I currently have two SGE2010's with a 4-port LAG configured between them. I'm looking to add another two SGE2010's and I want to add redundancy at the same time. The switches are currently in standalone mode. I don't have fiber connectors and was planning on just using copper for the uplinks.
My questions are:
- Is it possible to use stack mode in conjunction with 4-port LAG groups to create redundant 4-port links between all of the switches? The documentation says that ports 24&48 are reserved for stacking - does that mean I can't specify a LAG instead?
- If 4-port LAGs aren't possible, does that mean that these switches max out at 1Gpbs uplinks if you use stack mode?
Cisco Routers :: Updating RV042 Firmware
Sep 5, 2011will updating my RV042 firmware allow me to download larger files? How do I know what version to update to? Our current version is 1.3.7.4
View 1 Replies View RelatedD-Link DIR-655 :: Updating Firmware To V1.35NA?
Dec 30, 2010I tried updating my firmware of my DIR-655 from 1.34NA to 1.35NA (Hardware Version: A1/A2).
However, I found something strange while updating the firmware, that made me stop, in order to ask the question.
Previously, when I did an update, I would browse for the location, and put it in, and it would allow me to update from that location.
Now, it will allow it, but when I select to update from the desktop (C:usersderickdesktop),
it comes up with another location (C:fakepath) for the .bin file.
D-Link DIR-615 :: Check To See If Firmware Needs Updating?
May 21, 2011How do I check to see if my firmware needs updating? I want to connect it to a motorola 2210-02.
View 4 Replies View RelatedD-Link DIR-655 :: Recommended Firmware For Updating 1.21?
Aug 9, 2012i have an DIR-655 Hardware Version: A4, with Firmware Version: 1.21.Its dated: 2008/11/13.Do i get any improvement updating? And in such case, which FW should i use? It must be rock solid!
View 3 Replies View RelatedD-Link DIR-655 :: Updating Firmware On Router?
May 9, 2011a friend of mine(from the US) gave me this router. i am currently living here in the Philippines. and as I check my router's homepage, it gives me
Product Page: DIR-655
Hardware Version: A3
Firmware Version: 1.21
when I go to tools>firmware and check for the latest version, I get
Current Firmware Version : 1.21
Current Firmware Date : 2008/10/09
This firmware is the latest version.
I don't experience problems using this firmware but I think it's outdated because most of the users in the forum uses new firmwares.
where can I download firmware that is suitable for my router?? and is it risky?
should i download from the D-Link Philippines website? (the router was not bought here)[URL] or North America Firmwares should work fine on my router?
Cisco Switches :: How To Install Firmware Upgrade On 300 Series Switch
Jan 3, 2012I have downloaded the ros file, but can't find how to apply it. I know this information must be out there, but can't find it.
View 2 Replies View RelatedD-Link DIR-655 :: Cannot Access FTP Address After Updating Firmware
Dec 3, 2011I updated my firmware to the latest update a and then restored My personnel setting and now I can not access my ftp, I checked my IP address to make sure it didn't change , setting looks like did before update I went from firmware 121 to 135, was there new setting that I have to change to get it to work. I get no log in screen I get Windows cannot access this folder. Make sure you typed the file name correctly and that you have permission to access the folder?
Details:A connection with the server could not be established
D-Link DIR-655 :: Stopped Working After Updating Firmware To 3.35
Oct 21, 2011My DIR-655 stopped working after updating firmware to 3.35. Only power light comes on. port4 flashes for a microsecond when I plug it in. Recovery mode has not done anything. Computer acts like nothing is connected through Ethernet, says "No Cable Connected." Only power light stays on the whole time. I am guessing this thing is broken now. when i go through ipconfig, "no media connected." If not whats a good router under a hundred bucks today, had this router since early 2007.
View 10 Replies View RelatedCisco Wireless :: WAP200 Updating Firmware Without Connecting It To Network
Aug 2, 2012I was brought a WAP200 that was giving a client some issues. I've been told the first thing to try is to update/reinstall the firmware. I have the newest firmware file downloaded and saved, and I have the WAP200 plugged in and sitting on my desk.
I reset the access point and connected it directly to my computer with a patch cable, then entered the default IP address (192.168.1.245) to attempt to access the device. No go. Is that supposed to work and something is wrong with it? All I want to do is update the firmware, because if the device has been reset and the firmware reinstalled and it's still not working, then we'll just deem it defective and have it replaced.
Cisco Routers :: RV042 - Failure Updating To Firmware / 404 Not Found
Sep 5, 2011I just updated my RV042 to the firmware RV0XX-v4.0.4.02-tm-20110704-code.bin and now im having this error every time that i try to logon in the router? 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.
View 7 Replies View RelatedCisco Routers :: RV220W - After Updating Firmware There Is No DHCP And No Access To Anything
Apr 13, 2012I have a Cisco rv220w. I just tried updating the firmware. I used RV220W-Firmware-1.0.3.5.img. It rebooted, and now there is no DHCP and no access to anything. I tried the reset button for 10 seconds. That didn't do anything. The WAN and all the LAN lights light up. Power is on and solid. The light blinks alternating between the DMZ and the blank space to the right of wireless. How can I get this back to factory defaults?
View 5 Replies View RelatedUse 192.168.254.254 IP And Configuration Settings Limited And No Option Of Updating Firmware?
Jun 19, 2011i have Aztech DSL605EW wireless modem. I updated its firmware on some philipines Globle Broadband network's firmware. Now the problem is to open its configration I have to use 192.168.254.254 IP and the configuration settings are very limited and there is no option of updating firmware in it. I am stuck with it.
View 3 Replies View RelatedD-Link DIR-601 :: Wireless Router Won't Broadcast After Updating Firmware
Nov 29, 2011I recently updated my firmware for a DIR-601 router and have internet while hardwired, but no wireless. I saved the configuration settings before updating, but this doesn't even matter because my wireless router doesn't even show up in the list of available wireless network connections. Why isn't my router showing up? I tried a few things like unplugging it and resetting it, but nothing seems to work.
View 3 Replies View RelatedD-Link DIR-655 :: Unable To Access Web After Updating Firmware To 1.35NA
May 3, 2011Few days ago, I updated the firmware of my router to 1.35NA and everything seemed to be working fine at first. After a while though, I noticed my Nexus One phone wasn't getting internet through WiFi anymore. It is connected to WiFi still, and it can ping the other devices on the network but it won't connect to the web. I have a Xoom tablet connected to WiFi as well and it is getting access to the web, though it seems to drop web access from time to time too, even before the firmware update. My phone always had a connection to the web through WiFi before the update. The two PCs that have a wired connection work fine. In the router logs, I also noticed that "UPnP renew entry 255.255.255.255 <-> ... UDP timeout:0 'Teredo'" being spammed over and over since the update, which I read has something to do with IPv6?
View 14 Replies View RelatedLinksys Access Point :: WAP610N Updating Firmware
Mar 26, 2012I have a problem updating firmware for an WAP610N access point. The thing is i tryed to update from 1.0.01 to 1.0.03 and the update freezed at 49%. The next day it was restarted but of course it didn't worked again. The question is can i reset it some how so i can retry the firmware update ?
View 2 Replies View RelatedD-Link DIR-655 :: Save Configuration Of Router Before Updating To A New Firmware?
Jun 29, 2011For some reasons, my internet connection keeps dropping more often recently. My laptop still says it is connected to my network but I can just not have internet connection. It was not like that before but it happened more frequently now. What I did was to power off then on the modem and the router and everything will work fine again. I want to upgrade my firmware but I just wonder if I need to save all the configuration before doing the upgrading? If so, then how can I set it back to the old configuration that was saved?
View 5 Replies View RelatedLinksys Wireless Router :: Updating Firmware For E1200?
Feb 28, 2013When I bought my E1200 router my primary (in fact only) computer was a Windows laptop. Since that time I bought a MacBook Pro and have been using that as my primary computer. The Mac is running on the latest OS (Mountain Lion).
I would like to install the latest software to maintain the router on my Mac but I was told several months ago that there was no update available for Mountain Lion. If that has changed, and if so then where can I download the appropriate software?
D-Link DAP-1522 :: Can't Change LAN Connection Type After Updating Firmware
Mar 27, 2012I have my dap-1522 connected to my dir-655 in bridge mode. I was having intermitant connection problems with the dap-1522, so I updated the firmware to 1.41 for version A1. Now when I go to change the connection type to dynamic ip and save, it reverts back to static ip, which makes this thing useless for my network. Why won't it save?
View 6 Replies View RelatedLinksys Wireless Router :: EA2700 Gives Error When Updating The Firmware
Jul 3, 2012I have an EA2700 which I am trying to rollback to the older interface, however it errors out every time I try to install the firmware.All I ever get is this message: Unexpected Error The firmware update did not complete successfully. Please try again later.We've encountered an unexpected error. If the issue continues, please visit our Technical Support site.I've reset the router multiple times, powered it off overnight, re-downloaded the file multiple times, and am still unable to successfully rollback. Sometimes it even errors out when I try to set the password on the router itself and I have to reset it again before I can use the interface.
View 9 Replies View RelatedCisco Switches :: Cannot Bind ACL To Interface On SGE2010
Aug 30, 2011I am working on two SGE 2010 stacked and in routing mode. Everything work fine but before finishing the job, I wanted to lockdown all the network device so they would not be accessible from some subnets. Problem is, I cannot bind my ACLs to any interface. I get "Cannot apply because lack of HW resources." I am running firmware 3.0.0.18, and 3.0.1 release notes don't address that issue. TCAM utilization is at 3% Routing resources shows host: 200, routes:60, ip interfaces: 50 I have tried from the cli and get the same message.
View 3 Replies View RelatedCisco Switches :: Lag Between Stack Unit On Sge2010?
Jun 28, 2012Can I create lag betwen stack unit to increase speed between units ?? stack connection is only 1Gbit on ports 24/48 if posible lag link must be in trunk mode ?
View 4 Replies View RelatedCisco Switches :: SGE2010 Compatibility With Windows 7 Pro 64 Bit?
Aug 29, 2011Is there any issues with accessing the browser based GUI using Windows 7 64bit on a SGE2010 switch? I took the switch home and tried on my XP 32bit machine and works fine, but no luck on any windows 7 64bit pc's. I have tried 3 different new pc's on this new switch and no luck at all.
View 2 Replies View RelatedCisco Switches :: SGE2010 - Cannot Get DHCP Working
May 28, 2013We have a single SGE2010 in layer 3 mode switch with a Server 2008 DHCP server.
We will be implimenting a Voip netowork where the PC's connect to the voip phone. I would like to create another vlan - 10. I have created the vlan and assigned the IP on the swtich.
Routing seems to be working. I can ping both IP addresses of the switch on either vlan.
I cannot get DHCP working. In the SGE switch I have enabled DHCP Relay, enabled option 82, set my DHCP Interface as VLan1, and specified the DHCP servers IP address. On the ports I have set the port where the DHCP server connects to as a trunk port with Vlan 1 untagged and vlan 10 tagged. I have set the ports where the phones connect as a trunk port with vlan1 untagged and vlan 10 tagged.
Linksys Wireless Router :: Wrt54g - Can't Connect To Internet After Updating New Firmware
Dec 6, 2011i just updated my firmware on my wrt54g ver 2 router, went through all the steps it updated successfully after that i hit the reset button and unplugged the router as tehe online instructions said to. Now i can't connect to the interent at all with either of my two wired computers or through the wireless. All the lights on the front of the router are on like the power, internet, and wireless connectivity. Also the the two WAN ports my computers are connected to in the router the lights are on and it's recognising them. But I can't connect to the internet or even see the router on my network settings. Somone suggested to reconfigure the router but when i go to set up new connection my computer doesn't detect the router and also i cant connect to the router using the ip address 192.168.1.1/ since there is no internet connection. Is there a way to get to the router options or a way to revert it to its old firmware.
View 6 Replies View RelatedCisco Switches :: SGE2010 Lag Won't Work On Stacked Unit?
Jul 1, 2011We've have a 2 SGE2010-48 port, stacked. 4 LAGS are denifed, two on primary, whitch are working, two on slave unit are NOT working. Devices connected to LAGS are de the same and same configuration (Cisco ASA 5510).
View 3 Replies View RelatedCisco Switches :: SGE2010 - Change VLAN1 IP Address?
May 20, 2013I want to know how am i do to change the Vlan1`s IP address because the actual ip will be used in another vlan. Actually i haver 10 vlans in L3 mode (routing) implemented in it.
View 5 Replies View Related