Cisco Switches :: How To Install Firmware Upgrade On 300 Series Switch
Jan 3, 2012I have downloaded the ros file, but can't find how to apply it. I know this information must be out there, but can't find it.
View 2 Replies
ADVERTISEMENT
Cisco 7940 Series IP Phone - How To Upgrade Firmware
Aug 30, 2011I am facing a constant problem with cisco 7940 Ip Phones.
- I am able to configure it from Call Manager.
-But after that the phones starts restarting.
- I heard there is some issue with CISCO 7940 Farmware in recent times.
How to upgrade Firmware and where to get one.
Cisco Switches :: Firmware Upgrade For SG 300-28?
Mar 2, 2012Recently I brought SG 300-28.It came loaded with firmware ver 1.0.0.27.Can I upgrade it to ver 1.1.2.0 directly?
View 2 Replies View RelatedCisco Switching/Routing :: Upgrade Couple Of 6500 Series Switches
Apr 11, 2012My task is to upgrade a couple of 6500 series switches, 6513 with SUP720/MSFC3 (WS-SUP720) and Policy Feature Card 3 (WS-F6K-PFC3B) installed. How to upgrade those switches if in SSO redundancy mode with two SUPs installed?
I understand that it is good to connect to the MSFC3 via console and upgrade this first, is this correct?
I also have to upgrade some 6509 but I only can test it on one 6509-E, how to get everything up to date. [code]
Cisco Switches :: SG-300-28 / Upgrade With Latest Firmware
Dec 12, 2011We have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, any info for latest firmware is used for the same ?
View 6 Replies View RelatedCisco Switches :: Cannot Upgrade Firmware SRW224g4
Jan 19, 2013I'm trying to upgrade a switch SRW224G4 but without success. Model Name SRW224G4 Hardware Version 00.03.00Boot Version 1.0.0.06
I send the file via the XModem( SRW2xxG4_FW_1.2.3.0 ).
Cisco Switches :: Firmware Upgrade On SLM2008
Nov 11, 2012I have just attempted to load the latest firmware on an SLM2008, everything appeared to work as expected BUT, the switch is no longer pingable on its static IP doesn't appear to have attempted get an address via DHCP. I have attempted power cycling the switch but it has made no difference. The switch is still switching but I have no management any more. What to do next ?
View 1 Replies View RelatedCisco WAN :: Upgrade Firmware On SRW2048 Switch?
Sep 14, 2011It baffles me because the admin console doesn't look like it will browse your computer for a firmware update. Rather, it prefers you to specify a tftp or http server. I don't know how I'd set up my computer to be the http or tftp server and it doesn't really go into detail on what configurations or commands that would need to be used. I've used a tftp client in the past to send a firmware to routers and whatnot but not serve one.
View 1 Replies View RelatedCisco Switches :: SG300 Firmware Upgrade - How To Reload 1.0.0.27 Using CLI
Jul 27, 2011I've been having a problem with a brand new SG300-10 switch that I posted about yesterday. I checked the firmware and it was at 1.0.0.27 and the lastest is 1.1.0.73. So I backed up the current firmware and loaded the 1.1.0.73 version and it seem to be CLI based only, with no web GUI.
If so is there an easy way to reload the 1.0.0.27 using the CLI? There is nothing in the CLI docs that I can see unless it's buried.
The release notes for 1.1.0.73 don't say it's CLI only either, maybe something just went wrong but the CLI seems to be functional.
Cisco Switches :: SG300-28 In Boot Loop After Firmware Upgrade
Jun 22, 2012After performing a firmware upgrade on an SG300-20 switch from ver 1.1.0.73 to 1.2.5.70 the switch now boots up with the following error and resets:
30-Aug-2011 10:47:33 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter %s is too long.
The attached file contains a full output of the console boot process. I have tried loading different versions from the console, but all produce the same error.
Cisco Switches :: SGE2010 - Firmware Upgrade And Configuration Not Saving?
Oct 7, 2012Using the SGE 2010 for Microsoft NAP with 802.1x auth for switch access, which led to a few issues
What i have: An SGE 2010 48 port switch, firmware 3.0.0.17 Firmware upgrade: In order to ensure im not having problems due to old firmware, i tried to upgrade using ros_ls1_bp_ge_bx-3020.ros in order to move to 3.0.2, when uploading the file via TFTP, the upload completes and thats it, nothing happens.Restarting the device: As part of the upgrade process, i thought i might of had to reboot, so i rebooted, and found that all my settings were wiped clean, as if a factory reset had been performed.... and add further to pain, the backup of settings that i had taken do not seem to want to re-apply.NAP support: So i have tested my NPS (radius) server with NTRadping.exe and all is good, however i cannot get the SGE2010 to talk to it.... the authenticator state in the web interface is always listed as initialising.... im not sure if this is a simple incompatibility (hence the attempt at a firmware upgrade), a tag that needs to be set on the radius side or a switch misconfig.
1) how on earth do you upgrade the firmware?
2) why are none of my settings being saved when the device reboots ?
Cisco Switches :: Linksys SRW224G4 Firmware Upgrade Fail?
Jul 28, 2009I have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
Here the result for "ls_106-12216.ros"
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
[Code].....
Cisco Switches :: SRW248G4 Firmware Upgrade Failed / Cannot Restore
Dec 12, 2012with TFTP upgrade SRW2xxG4_FW_1.2.3.0.ros and WEB interface after the restart, the switch will not start, display HyperTerminal link. You can also restore the switches do not?
View 1 Replies View RelatedCisco Switching/Routing :: Upgrade The Firmware In C2960 Switch To 15(1) SE2?
Feb 14, 2012i am trying to upgrade the firmware in my C2960 switch to 15(1) SE2, and i get the error:Failed to execute the command archive download -sw /overwrite /http iosFile
View 2 Replies View RelatedCisco Switches :: Where Are Languages File For Switch Series 200
Jun 30, 2011i can't find languages file for series 200 switch...where are?
View 1 Replies View RelatedCisco Switches :: Dual Stacked Series 500 Switch?
May 10, 2012I am about to buy 2x Series 500 switches but before that I have a design to be sure :I want to create a redondant network so it is the reason why I want to stack 2x Series 500 switches.Each server on my network (ESX and Windows 2008) are connected with two NIC (one port on the first switch , one port on the second switch), with trunk mode + etherchannel for LACP.
First question : I saw that the limitation is up to 8 etherchanel groups, can I have a mix of multiple servers on the same etherchannel group or should I create one etherchanel group for one server with only the two NIC inside?
Second question:I want to use the series 500 to do intervlan routing and want to be sure that if the the ports are in trunk mode with some vlan set on the card itself that the default gateway for the vlan will be propagated on the two switches (in stack mode) and will not cause any issues when both switchs works fine and if one switch crashes?
Cisco Switches :: SGE2000 Illegal Software Format - Firmware Upgrade
Jan 10, 2012I am trying to update the SGE2000v1.0 with 24ports to 3.0.1.0: url...I got the error "illegal software format" using tftp.
View 2 Replies View RelatedRouters / Switches :: How To Install Two Wireless Routers In Series
Dec 31, 2012The first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.
View 3 Replies View RelatedCisco Switches :: Can't Get VLAN To Work On A SF300 Series Switch
Sep 9, 2012I have a SF 300-24 24-Port 10/100 Managed Switch and I am trying to set some VLANs. The image below shows how I want it to be setup:Since the remote site goes through the Internet, making port 20 an 802.1Q trunk over the two VLANs will give WAN connectivity to VPN/E-mail.I've tried all sort of settings [ see attachments] but can't get it work.
View 5 Replies View RelatedCisco Switches :: Routing Between Two Vlans On An SG300 Series Switch
Oct 22, 2011I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
Cisco Switches :: SA520 Lack Of HW Resources / ESW Series Switch
Jun 5, 2011Updated formware of a partners ESW224 to the current GA code.I tried to add a ACL to a ESW switch. The switch was connected to a SA520.
I setup a guest network on a AP541 and propogated that guest VAP VLAN down through a ESW224 and down to a SA520.
On the SA520 I disabled IP routing between VLANs. All worked OK.
Guest and corporate clients could get differeing IP addresses deopending on which VAP they connect to.
But the wireless guests could still ping the management interface of the SA520. This is a security violation for the partner.Tried to setup a ACL on a ESW224 to deny traffic from getting to the normal corporate vlan or 192.168.75.0.
But received a popup on the ESW when i tried to create a ACL. It suggested there is a lack HW resources.
I disabled ESW advanced QOS.Tried to add a ACL , but still have a error message saying lack of HW resources.Why do I get a message saying lack of HW resources ?
Cisco Switching/Routing :: Any Challenge To Upgrade Core Switch 6500 Series From Nexus 7009 Which Runs NxOS
Jan 28, 2013Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
Cisco Switching/Routing :: 3750 - Firmware Upgrade Of Switch Stack Fails
May 9, 2012I have a stack of 4 Cisco Switch 3750 (1 x WS-C3750G-24T, 2 x WS-C3750-48P and 1 x WS-C3750V2-48PS) and I want to do an firmware upgrade of this stack. Actually, all the 4 switches are at the firmware version 12.2(50) SE1 "IPBase" and I want to upgrade them to 12.2(55)SE5 IPBase. According to the release notes, all the switches in my stack are supported.
To upgrade the firmware, I use the command "archive download-sw /imageonly /overwrite tftp://IP_Address/c3750-ipbaselmk9-tar.122-55.SE5.tar" The firmware gets uploaded correctly but then I get the error message "There is insufficient space in flash: to install the required image. Clean up some old images, and try again."
When I do a "show flash", I see that the switch has 5650944 bytes free of 15998976 bytes.
How can i upgrade my switches? Is there an error in my command which I use? Do I need to add an other option?
The problem is, the switches are located in a branch office and there is no direct access to them. Everything must be done remotely.
Cisco Switches :: Series 200 Smart Switch Not Communicating - DHCP Blocked
May 29, 2011I have a small, simple small business network. There are 2 switches - an 8-port switch connected to my main Windows server (which is the DHCP provider for the network), and a 24-port switch which is plugged into the 8-port switch.
I replaced these switches (Dell unmanaged switches) with the Cisco 200 series smart switches (the 8-port and 26-port models). When I plug the 26-port switch into the 8-port switch, it is unable to get its DHCP address from the Windows server. Also, any device plugged into the 26-port switch cannot communicate with any other device, and all of the ethernet port lights flash at the same time at the same frequency - quite a light show!
If I plug the Windows server DIRECTLY into the 26-port switch it receives a DHCP address.
I have tried a 2nd Cisco 26-port swtich and it does the same thing, so I assume it is not a hardware issue.
Cisco WAN :: 6500 Series Switch / Configured Port Channel On Both Switches With 2 Gig Interface
Jan 9, 2012we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
Cisco Switches :: Updating Firmware SGE2010 Switch
Oct 20, 2012what is the process of updating firmware on a SGE2010.
I would usually use TFTP - but, I can't see the TFTP command on these SGE2010's
Cisco Switches :: Sge2010p Software Upgrade Switch Always Boots
Aug 6, 2011I have just downloaded new software for sge2010p. I had tried to made an upgrade on some switches, but switches still boot with the old software.I have installed software 3.0.0.18 and boot 2.0.0.03. I have downloaded software 3.0.1 from cisco, put it on tftp and started an upgrade via switch web interface. I have checked that the active image is set to 1, and started the upgrade.Switch has downloaded soft from tftp, and reported that process has been finished without errors.After the restart switch have 3.0.0.18 software again. I have try to do this same on 4 different switches working in L3 and L2 mode - always with the same effect.Should I upgrade both images in the same time to get this work?
I have noticed, that the new firmware is located on image 2.
# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active*
[Code] ...
So I try to set active image via console command:
# boot system image-2
and again...
a# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active*
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active
"*" designates that the image was selected for the next boot
Finally i have tried to set the active image to "2" using console menu: I have set it like this:
Active Image
============
Unit ID Active Image Active Image after Reset
======= ============ ========================
1 Image 1 Image 2
and save..
[Code]
Where is the right place to set active image for 2. Is the "active image" settings only sets the firmware image which switch uses or configuration files too?
Cisco Switches :: Connect 2 SGE200 Series Switches Over Gbit / Fiber
Mar 27, 2013I have a stack of 6 switches and I want to add another over the gbit connector using fiber. I already connected but I can acces the network from the new switch. I don't have any issues on my Stack all resources are available Do I need to do some special setup or connection to enable this? Can be stacked like the others? I already usen the 2 stacking port can i Add another switch?
View 3 Replies View RelatedCisco Switches :: How To Erase All Configuration In ESW 500 Series Switches
Aug 21, 2011How to erase or remove configuration file from ESW 500 Series Switches?
View 2 Replies View RelatedD-Link DIR-615 :: Firmware Version 3.0 / 3.13 Won't Install
Nov 12, 2012Recently he was having connection issues so decided to upgrade firmware and for some reason he did it through the management console (clicked the update to have it download the new file automatically and instantly upgrade instead of doing it manually himself). Told him not to do that anymore. Anyway, it wiped the existing firmware obviously and did not update to the newest. I came over to find it wouldn't connect at all. I was able to get into the reset console (hold reset while powering on, manual set IP on computer to 192.168.0.2 and gateway to 192.168.0.1 an then pointed the browser to 192.168.0.1).This window shows the current firmware as version 1.0.0.1 dated in 2007.I had downloaded the version 3.0 firmware and the most recent version 3.13 and had them on a flash drive, dropped them on the hard drive and attempted to flash first the newest and then the 3. Neither one would take and the router remains down. The page itself never changed after hitting SEND to upload the firmware, the browser displayed a progress bar for "uploading" and hit 100% then just sat saying "waiting for response from 192.168.0.1" until the browser timed out after several minutes.
View 4 Replies View RelatedCisco :: WLC 2500 Series / Differences Between 7.0 And 7.2 Firmware?
Mar 28, 2012which differences exist between 7.0 and 7.2 firmwares? I have to decide/choose which of them to run, before continuing to configure my WLAN infrastructure.
View 3 Replies View RelatedBelkin Routers :: F5D5231-4 - Firmware To Install Mac
May 31, 2013Is there firmware available to support the 4-port Cable/ DSL Gateway Router model # F5D5231-4 Ver: 1103. The router is several years old and the installation guide suggests checking the Belkin web site for a Mac installation wizard. I don't see any ref. to a Mac down load there.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: ISE Install Upgrade With 3395
Mar 17, 2013I have an ISE 3395 appliance that comes with ISE version 1.1.1.I've decided to upgrade it to version 1.1.2 patch 5 (latest patch version) and played with it for a few days. I set it up as a stand-alone box.
Now, I need to deploy this box as administration and monitoring. So, I put in the command "application reset-factory" to set it back to factory.Does it mean the ISE version of this box will still be at version 1.1.2 patch 5 and I will get a clean box to do whatever I want, similar to Cisco IOS of "write erase" and "reload" to have a clean box?
