Cisco Switches :: SA520 Lack Of HW Resources / ESW Series Switch
Jun 5, 2011
Updated formware of a partners ESW224 to the current GA code.I tried to add a ACL to a ESW switch. The switch was connected to a SA520.
I setup a guest network on a AP541 and propogated that guest VAP VLAN down through a ESW224 and down to a SA520.
On the SA520 I disabled IP routing between VLANs. All worked OK.
Guest and corporate clients could get differeing IP addresses deopending on which VAP they connect to.
But the wireless guests could still ping the management interface of the SA520. This is a security violation for the partner.Tried to setup a ACL on a ESW224 to deny traffic from getting to the normal corporate vlan or 192.168.75.0.
But received a popup on the ESW when i tried to create a ACL. It suggested there is a lack HW resources.
I disabled ESW advanced QOS.Tried to add a ACL , but still have a error message saying lack of HW resources.Why do I get a message saying lack of HW resources ?
View 2 Replies
ADVERTISEMENT
Sep 6, 2012
I want to use Cisco VPN Client to VPN to my SA520 to manage a UC320W. I can establish a VPN connection to the SA and ping both the SA and a switch that I have on the network, but I cannot ping my UC. I've set up firewall rules to allow ANY-ANY access from LAN-WAN, and a WAN-LAN rule to allow a certain range of IP addresses (the IP addresses assigned from the VPN DHCP pool, in this case, 192.168.12.x) access to the UC.
My SA IP address is 192.168.75.1 and my UC is 192.168.75.2 (I can ping both when I am directly connected to a LAN port on either equipment).
View 1 Replies
View Related
Oct 17, 2011
Last week and just yesterday, our switch SG200 50/50 logged an error like this:
%CDP-E-MALFORMED_TLV: CDP message from 88:43:e1:ab:66:f8 cached with illegal Appliance VLAN-ID TLV
At the time of the error, the SA520 router's LAN Port 1 where the SG200 Port 49 connected went down. (Light is OFF) So internet is down and other V LAN are disconnected. The MAC address on the log is the SA520 router. This happens 2x now and it needs for me to reboot both switch and router. and goes back again online.
SG200 50/50 Port Firmware 1.1.1.8
SA 520 Firmware (Primary/Sec):2.1.51/2.1.18
View 4 Replies
View Related
Jun 30, 2011
i can't find languages file for series 200 switch...where are?
View 1 Replies
View Related
May 10, 2012
I am about to buy 2x Series 500 switches but before that I have a design to be sure :I want to create a redondant network so it is the reason why I want to stack 2x Series 500 switches.Each server on my network (ESX and Windows 2008) are connected with two NIC (one port on the first switch , one port on the second switch), with trunk mode + etherchannel for LACP.
First question : I saw that the limitation is up to 8 etherchanel groups, can I have a mix of multiple servers on the same etherchannel group or should I create one etherchanel group for one server with only the two NIC inside?
Second question:I want to use the series 500 to do intervlan routing and want to be sure that if the the ports are in trunk mode with some vlan set on the card itself that the default gateway for the vlan will be propagated on the two switches (in stack mode) and will not cause any issues when both switchs works fine and if one switch crashes?
View 3 Replies
View Related
Sep 9, 2012
I have a SF 300-24 24-Port 10/100 Managed Switch and I am trying to set some VLANs. The image below shows how I want it to be setup:Since the remote site goes through the Internet, making port 20 an 802.1Q trunk over the two VLANs will give WAN connectivity to VPN/E-mail.I've tried all sort of settings [ see attachments] but can't get it work.
View 5 Replies
View Related
Oct 22, 2011
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
View 6 Replies
View Related
Jan 3, 2012
I have downloaded the ros file, but can't find how to apply it. I know this information must be out there, but can't find it.
View 2 Replies
View Related
May 29, 2011
I have a small, simple small business network. There are 2 switches - an 8-port switch connected to my main Windows server (which is the DHCP provider for the network), and a 24-port switch which is plugged into the 8-port switch.
I replaced these switches (Dell unmanaged switches) with the Cisco 200 series smart switches (the 8-port and 26-port models). When I plug the 26-port switch into the 8-port switch, it is unable to get its DHCP address from the Windows server. Also, any device plugged into the 26-port switch cannot communicate with any other device, and all of the ethernet port lights flash at the same time at the same frequency - quite a light show!
If I plug the Windows server DIRECTLY into the 26-port switch it receives a DHCP address.
I have tried a 2nd Cisco 26-port swtich and it does the same thing, so I assume it is not a hardware issue.
View 5 Replies
View Related
Jan 9, 2012
we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
View 10 Replies
View Related
Oct 6, 2011
We setup about 5 MAC based VLAN groups with about 40 MACs total and now we are getting "There are no resources for this range.." when we try to add more MACs or try to assign them to the port/VLAN "MAC-Based Groups to VLAN". We tried to reboot and use the CLI, same error. Is there some undocumented small limit on the MAC based VLAN groups?
View 2 Replies
View Related
Jan 19, 2013
We have a two separate businesses in the same building who will both need access to shared resources and the same internet connection. They will need to remain on separate subnets and cannot communicate directly to each other. The current switch is a Cisco ESW-520-48P and we are looking at purchasing an SG-300-20P for the new business moving in. Heres how we envisage setting it up:
ESW-520 will host Company A's network. Workstations, servers etcSG-300 will have two VLANS. VLAN1 will host all Company B's network. Workstations, servers etc. VLAN2 will host the shared resources such as printers. The internet gateway is a UNIX based system with 3 NICS. 2 NICS are taken up by ADSL connections while the other NIC is the LAN, which would connect to VLAN2 on the SG-300. We would like to define which ADSL connection to route through depending on which subnet traffic is originating. The ESW-520 will need access to the shared resources and internet gateway on VLAN2 on the SG-300.
View 4 Replies
View Related
Mar 27, 2013
I have a stack of 6 switches and I want to add another over the gbit connector using fiber. I already connected but I can acces the network from the new switch. I don't have any issues on my Stack all resources are available Do I need to do some special setup or connection to enable this? Can be stacked like the others? I already usen the 2 stacking port can i Add another switch?
View 3 Replies
View Related
Jul 14, 2012
I recently upgraded to 1.0.3 fw on my x3000 in the hope of getting rid of the issue with my upload speed. However, now it is denying me connection to the outside world about once a day. It is getting an ip, even if I am renewing the IP address.I am using it on my Fullrate broadband 20/2 connection, and I can at most get 1mbit UL, but with the old router, I could get 2.1mbit. I bought this one because the other one sucked (the standard from my ISP).I have set the router up as the old one was, however, it is still slow, and now it also needs reset every day.
View 7 Replies
View Related
Aug 21, 2011
How to erase or remove configuration file from ESW 500 Series Switches?
View 2 Replies
View Related
Dec 24, 2011
I have a WRT610N V1 wireless router. The wireless has always been a little quirky and stopped working for short periods of time. It now won't connect at all. My computer sees the signals for both 2.4 and 5 MHz networks but can't connect to them. It was working fine until yesterday but now I can't get it to work. I also have a couple of guests, neither of whom can connect to the wirelesss networks. The router works fine for wired connections (I also have the guest computers connected through a WD Powerline box) and the MAC filter is disabled. It's set for OpenDNS and so used two fixed DNS addresses. I tried resetting and powering down the router.
View 2 Replies
View Related
Oct 17, 2012
how to setup 802.1x on the Cisco 500 Series Switches.I have done the whole implamentation in the past with Catalysts and ACS.But would like to see a guide for the 500 series.Do we need the Cisco ACS or can we use RADIUS on Windows?
View 1 Replies
View Related
Dec 14, 2011
Looking for Information about Latest IOS Available for switch Series 3560, Guide the latest IOS sopprted Features Specification And Also Guide the Switch Minimum Hardware capacity Require to upgrade with the latest IOS.
View 2 Replies
View Related
Aug 22, 2011
we are trying to do an automatic backup of our switches config trough snmp.my script can easily backup cisco 2950-2960-3550-3560 using snmp.but I dont know the mib to use to backup the cisco small business serie 300 switches.
View 6 Replies
View Related
Apr 24, 2013
what the intention behind adding SSH to the SG200 series switches was. Is it to allow SCP copies to and from the switch for configuration and firmware updates OR is it to allow CLI access to the switches.
I have tried to SSH to the switch using PuTTY from Windows and native SSH from Linux/Unix clients, but nothing happens.
Is there some other area of configuration to enable communcation via SSH?
View 5 Replies
View Related
May 28, 2013
Am I correct in thinking that 200 series swiches now support SNMP using v1.3?
View 1 Replies
View Related
Dec 29, 2011
I just set up a new Cisco 300 Series Switch to replace an old switch on our network. We have probably 6 switches around our facility, all of them working fine (except for this one).
We have Windows SBS 2008. If I plug a PC directly into the switch that is NOT configured for SBS (in other words, it hasn't joined the domain) I have no problems accessing the internet. However if I connect PCs configured for SBS that have joined the domain to the switch, they can only access our intranet and not connect out to the internet.
The switch is currently configured for a static IP address and the client PCs are all dynamic.
View 13 Replies
View Related
Dec 1, 2011
We inherited a lot of the equipment from another team of network administrators and every now and then, we run into a switch with some old code or configuration that was left behind and missed by us. Today, I discovered that CPP was enabled on 3 of our access-layer switches in one of the buildings we support.
View 3 Replies
View Related
Apr 2, 2012
what is the reason that cisco 1130 series ap cannot be seen by switch it connected to, by CDP protocol
View 2 Replies
View Related
Dec 17, 2011
I am looking for The latest IOS Available for cisco 3560 Series Switch, User guide for the same And All Supported features specification Guide.
View 7 Replies
View Related
Apr 2, 2012
Why it could be that switch cannot see Cisco ap 1130 series by cdp .
View 1 Replies
View Related
Mar 6, 2013
How config dynamic alp inspection for 300 or 500 series ? I find in admin guide it's no simple to do.
View 8 Replies
View Related
Jul 25, 2011
I have a CiscoWorks LMS 2.6 and i would like to know if the new Switches Catalyst 2960-S Series are supported with this LMS version?
View 1 Replies
View Related
Mar 29, 2011
I have a problem I have Cisco 2960 series switches with ip address 10.10.10.2 255.255.255.0 works but can not connect to the Internet
View 1 Replies
View Related
Oct 18, 2012
I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies
View Related
Jan 19, 2011
I connect a WRV210 router with Small Business 100 Series Unmanaged Switch SG 100-16 Switch. But the switch is not work with the router.In the port of switch (connect with router), no light. In router, the port is disable.Do I need cross-over ethernet cable connect with them?I tried connect WRV210 directly to computer, that is work. I tried connect WRV210 to other (no name) switch and connect this switch with Cisco Switch 100-16 switch than they are work. why?
View 1 Replies
View Related
Apr 23, 2013
Am new to Nexus switching, i have a Nexus box that i need to link with IBM servers with 10GB Network Cards.
how to set up fiber channel on this machine
View 4 Replies
View Related
Mar 3, 2013
Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?
View 1 Replies
View Related
