Cisco WAN :: WRV210 Not Work With SMB Series SG 100 16 Ports Switch
Jan 19, 2011
I connect a WRV210 router with Small Business 100 Series Unmanaged Switch SG 100-16 Switch. But the switch is not work with the router.In the port of switch (connect with router), no light. In router, the port is disable.Do I need cross-over ethernet cable connect with them?I tried connect WRV210 directly to computer, that is work. I tried connect WRV210 to other (no name) switch and connect this switch with Cisco Switch 100-16 switch than they are work. why?
View 1 Replies
ADVERTISEMENT
Sep 9, 2012
I have a SF 300-24 24-Port 10/100 Managed Switch and I am trying to set some VLANs. The image below shows how I want it to be setup:Since the remote site goes through the Internet, making port 20 an 802.1Q trunk over the two VLANs will give WAN connectivity to VPN/E-mail.I've tried all sort of settings [ see attachments] but can't get it work.
View 5 Replies
View Related
Feb 21, 2011
I have a big problem with my cisco wrv210. I want to use URL Filtering to block facebook.
Enable
ip range : 192.168.2.5-192.168.2.254
url string : Facebook, www.facebook.com , facebook.com notting work.
View 1 Replies
View Related
Mar 6, 2012
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies
View Related
Aug 7, 2011
How many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies
View Related
May 2, 2012
I have a Cisco 2600 series with 2 X Fast Ethernet ports and I would like to configure the cisco to perform the task if it is possible.The scenario is:
2 networks:
F0/0: 192.168.x.x
F0/1: 10.1.x.x
No communication between them except one way multicast from F0/1 to F0/0.
View 1 Replies
View Related
May 21, 2012
I have a Cisco Catalyst 2960 series switch. When I connect another switch or a VMWare Esx server on one of the ports, the port blinks for few seconds and then goes off. When I connect a desktop or laptop or a windows server the ports stay led and I can access resources on the network. However, when connect another switch or a vmware esx server, the port is disabled.
What config in the switch can I check to make sure the ports stay on regardless when I connect a desktop / laptop, switch or vmware server?
View 2 Replies
View Related
Apr 28, 2012
I am little confused about the location of FIB table and adjacency table in both cisco 6500 series and fixed ports switches .In case of 6500 series switches
"Central CEF mode:The CEF FIB and adjacency tables reside on the route processor,and the route processor performs the express forwarding. Use this CEF mode when line cards are not available for CEF switching, or when features are not compatible with distributed CEF."
If line cards do no support CEF, then FIB and adjacency tables are built and are located on route processor( control plane ). Data plane operations are implemented in software and route processor performs those operations.
Some Cisco switches actually use different hardware to control the different planes. For example, the Cisco Catalyst 6500 is a modular switch that uses the Multilayer Switch.Feature Card (MSFC) for control-plane operations, and the supervisor Policy Feature Card (PFC) for the data-plane operations.
Supervisor module has has MSFC and PFC. MSFC implements control plane operation where as PFC implements data plane operation.But the first paragraph says in Central cef mode, both data plane and control plane operations are implemented by route processor. [code]
Do these switches implement the Central mode cef in same way as mentioned above. i.e
"Central CEF mode:The CEF FIB and adjacency tables reside on the route processor and the route processor performs the express forwarding. Use this CEF mode whenline cards are not available for CEF switching, or when features are not compatible with distributed CEF."Or fixed ports switches such as 3750 implement data plane operation in hardware where FIB tabe and adjacency table are maintained on Data plane.
View 3 Replies
View Related
Jul 14, 2011
I have a customer who bought Cisco Aironet 3500 Series. Currently 4404 WISM Controllers are installed with 1142 Access-Points. The WLC-Version is 6.0.199.
Will the 3500 Series Access-Points work? (Of course without the spectrum intelligence feature)?
The Q&A says the following: Are there any concerns with supporting the new Cisco Aironet 3500 Series Access Points with the older Cisco 2000, 2100, 4100, or 4400 Series Wireless LAN Controllers?
View 2 Replies
View Related
Oct 11, 2006
I need to know if LAG channel groups can be used to increase capacity of media converted links? (i.e. wireless links).For example.. aggregating two 1300 series wireless bridges via 2 switches.
View 1 Replies
View Related
Jan 8, 2013
We have been using a dhcp and tftp server to automatically configure branch WAN routers such as 1751's and 1841's for years but, have recently purchased a 1921 and 1941 as possible next generation replacements. The problem is when the 1900 series power up instead of getting a dhcp address directions to the tftp server it boots up and asks for the user name to be immediately changed or you will be "locked out". Any workaround to this so that I can again go back to download my common configuration? Or any other way of automatically configuring the newer version ios? Doing extra steps for 500 WAN branch routers is time consuming. Doing configurations without automation for that many is moving in the wrong direction.
View 1 Replies
View Related
Feb 8, 2013
i've tried plugging in various devices (computer & solar panel management device) into the ethernet ports to no avail. i just updated the firmware, reset the router, and still no luck. all of the lights work when i reset and the wifi works fine. do i need to do something in the settings to turn on the hard connection?
View 3 Replies
View Related
Mar 23, 2012
I need opening up some ports for a sftp client at work. software version 8.0 (3) device manager version 6.1 (1)
View 4 Replies
View Related
Jan 2, 2012
Purchased desktop from micropro in 2002. We finally upgraded to cable internet in 2011, Wife purchased Think Pad laptop also in 2011 (wireless enabled). Purchased Belkin wireless router and want to network these 2 computers.1. My desktop has been demoted to the garage. I have wiped it clean (i hope) by doing a reinstall of XP Pro. Now some of the USP ports won't work. How do I network these two machines?
View 1 Replies
View Related
Feb 1, 2011
I have the Linksys WRT54G Wireless Router, when i hook my at&t modem to the modem port on the router the wireless portion of the router works, when i plug any pc into the Ethernet ports it doesnt work!If i plug the modem into the Ethernet port and plug other pcs into the other existing Ethernet ports it works by Ethernet but not wireless.
View 1 Replies
View Related
Dec 27, 2011
I'm trying to get the silly iTunes Wi-Fi sync to work , and I've been told to ensure that these ports are open:5297 TCP 5298 TCP/UDP and 5353 UDP in the hardware router. How do I do this with the DIR-655 (HW version A3, FW version 1.35NA)?
View 1 Replies
View Related
Dec 29, 2011
I just set up a new Cisco 300 Series Switch to replace an old switch on our network. We have probably 6 switches around our facility, all of them working fine (except for this one).
We have Windows SBS 2008. If I plug a PC directly into the switch that is NOT configured for SBS (in other words, it hasn't joined the domain) I have no problems accessing the internet. However if I connect PCs configured for SBS that have joined the domain to the switch, they can only access our intranet and not connect out to the internet.
The switch is currently configured for a static IP address and the client PCs are all dynamic.
View 13 Replies
View Related
Dec 1, 2011
We inherited a lot of the equipment from another team of network administrators and every now and then, we run into a switch with some old code or configuration that was left behind and missed by us. Today, I discovered that CPP was enabled on 3 of our access-layer switches in one of the buildings we support.
View 3 Replies
View Related
Apr 2, 2012
what is the reason that cisco 1130 series ap cannot be seen by switch it connected to, by CDP protocol
View 2 Replies
View Related
Dec 17, 2011
I am looking for The latest IOS Available for cisco 3560 Series Switch, User guide for the same And All Supported features specification Guide.
View 7 Replies
View Related
Apr 2, 2012
Why it could be that switch cannot see Cisco ap 1130 series by cdp .
View 1 Replies
View Related
Oct 18, 2012
I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies
View Related
Jun 30, 2011
i can't find languages file for series 200 switch...where are?
View 1 Replies
View Related
Apr 23, 2013
Am new to Nexus switching, i have a Nexus box that i need to link with IBM servers with 10GB Network Cards.
how to set up fiber channel on this machine
View 4 Replies
View Related
May 10, 2012
I am about to buy 2x Series 500 switches but before that I have a design to be sure :I want to create a redondant network so it is the reason why I want to stack 2x Series 500 switches.Each server on my network (ESX and Windows 2008) are connected with two NIC (one port on the first switch , one port on the second switch), with trunk mode + etherchannel for LACP.
First question : I saw that the limitation is up to 8 etherchanel groups, can I have a mix of multiple servers on the same etherchannel group or should I create one etherchanel group for one server with only the two NIC inside?
Second question:I want to use the series 500 to do intervlan routing and want to be sure that if the the ports are in trunk mode with some vlan set on the card itself that the default gateway for the vlan will be propagated on the two switches (in stack mode) and will not cause any issues when both switchs works fine and if one switch crashes?
View 3 Replies
View Related
Mar 3, 2013
Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?
View 1 Replies
View Related
Feb 24, 2013
Region : Mexico
Model : TD-W8968
Hardware Version : V1
Firmware Version : the last version of this web page, i forgot number
ISP : TELMEX (infinitum)
i have some problems to configure the port forwarding in my router, don't it work ! but the port number 80 it works with my sub-domain in the internet. after i change this port to 8080 still dont work the port forwarding. the FTP server its ok.
[code]......
View 3 Replies
View Related
Oct 14, 2012
I have a routed interface on a Cisco 6500 Series switch. I am trying to find a way to adjust the tcp mss.To date I have not yet been able to find a way to accomplish this. Is this just not supported?
View 3 Replies
View Related
May 13, 2012
We are using cisco ME 3400 E series switch. Which port we can use as CFM port ? We configured CFM in gig port.Is all the ports will act as CFM port or any separate CLI command is there for enable ?
View 0 Replies
View Related
Oct 22, 2011
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
View 6 Replies
View Related
Feb 3, 2013
I have mounted a cisco 2950G series switch in the network. we are working on Multicasting so I have LAN connectivity from one location ot other.
Situation:- 1- we do not have to do anything at remote location. its already done with final configuration and working fine because we other location witch are connected with this same HP switch at remote site and working fine but problem is only with one location where I have changed switch(cisco2960). when i connect cable from MUx to the switch cisco switch (Local) on particular port its does not response (LED continuously glowing amber color and does not go to green color) and communication does not start.for fixing this issue I have done so many things, vlan, duplex, speed- done everything but response.
situation 2:-when I changed this cisco device and use any other vendor's switch whether its manageable not manageable its get start proper communication. so I am unable to figure out whats the issue with. is there new or latest switch are not compatible with other vendor.
View 1 Replies
View Related
Jun 5, 2011
Updated formware of a partners ESW224 to the current GA code.I tried to add a ACL to a ESW switch. The switch was connected to a SA520.
I setup a guest network on a AP541 and propogated that guest VAP VLAN down through a ESW224 and down to a SA520.
On the SA520 I disabled IP routing between VLANs. All worked OK.
Guest and corporate clients could get differeing IP addresses deopending on which VAP they connect to.
But the wireless guests could still ping the management interface of the SA520. This is a security violation for the partner.Tried to setup a ACL on a ESW224 to deny traffic from getting to the normal corporate vlan or 192.168.75.0.
But received a popup on the ESW when i tried to create a ACL. It suggested there is a lack HW resources.
I disabled ESW advanced QOS.Tried to add a ACL , but still have a error message saying lack of HW resources.Why do I get a message saying lack of HW resources ?
View 2 Replies
View Related
Sep 29, 2011
When will Campus Manager support the 2960S switch series?
View 2 Replies
View Related
