Cisco WAN :: 8.0 (3) Opening Up Some Ports For Sftp Client At Work
Mar 23, 2012I need opening up some ports for a sftp client at work. software version 8.0 (3) device manager version 6.1 (1)
View 4 Replies
ADVERTISEMENT
D-link Dir-655 :: Opening Ports - Getting Itunes Wifi Sync To Work?
Dec 27, 2011I'm trying to get the silly iTunes Wi-Fi sync to work , and I've been told to ensure that these ports are open:5297 TCP 5298 TCP/UDP and 5353 UDP in the hardware router. How do I do this with the DIR-655 (HW version A3, FW version 1.35NA)?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: SFTP Backup Does Not Work For ACS 5.3
Feb 21, 2012We have ACS 5.3, and trying to set up sftp backup on freesshd server. SSH connection works, but ACS cannot copy backup file to sftp server, we get following errors:
Acs.MGMT.ACSVIEW Backup failed: CARS_XM_SSH_CONNECT : -306 : SSH connect error
FTP backup works fine.
Cisco :: Opening Ports On Firewall?
Apr 24, 2012We have a DVR here at work that has a web interface on port 100. From our internal network we just use http:192.168.100.40:100. What is the best way to set that up on cisco 5510 firewall. I have cisco asdm and set a access rule: enabled=checked ; source=any ; destination= 192.168.100.40 ; service= tcp 100 ; action=permit. It shows a couple of hits when I go to [URL]
View 7 Replies View RelatedCisco WAN :: Opening Some Inbound Ports On PIX Version 6.3(5)
Oct 16, 2012I have been asked to open some ports in order for a CCTV company to connect to an internal CCTV server on our LAN.
We have a Pix running PIX Version 6.3(5) I am ok configuring an ASA for the above but not a Pix.
Cisco Firewall :: Opening Ports On 5505?
Jan 2, 2013I am trying to configure a new 5505 but I am having difficulties opening ports that allow traffic in from the outside. My setup is Comcast Business Modem (w/ single static IP) -> ASA (10.0.0.1) -> (dumb) Switch -> NAS (10.0.0.10). I am attemping to open port 5001 to the NAS. I am very new to IOS so I have mostly been working in ASDM. Not sure if I am overcomplicating this for myself or what but I am stuck.
My running config is -
ASA Version 8.2(5)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
[Code].....
Belkin F9K1002V2 Not Opening Ports
Apr 20, 2012What I'm trying to do is to get my Xbox connected to the internet through my router (wired connection), but I want to have my NAT open also. But when I put in a static IP into the Xbox manually and open the ports in my router, it makes it so my Xbox can't connect to Xbox Live at all. Although, if I just leave it to the automatic setting on my Xboxs network options, I can connect just fine. But, I end up having a strict NAT type, unless I restore to factory defaults in the networking options on the Xbox.
View 2 Replies View RelatedOpening Ports 80 / 5000 And 22 In Modem?
Jan 16, 2013how can I open my port 80, 5000, and 22 in my modem.
View 1 Replies View RelatedCisco Firewall :: Opening Outbound Ports On ASA5505
Oct 2, 2012I need to open some outbound ports in order for our CCTV company to receive alarms from our internal CCTV Machine.
The ip addresses of the company who access the CCTV are as follows:
213.130.134.56
81.130.198.97
The above are fixed IP addresses. The internal machine is on 192.168.204.170
The outbound ports that I need to open are the following:
TCP
21
23
80
5201
UDP
1025
2074
2075
I have access to the current config if needs be.
D-Link DIR-825 :: Portforwarding Leads To Ports But Not Opening?
Jan 25, 2013I've had this router for a few months after my last one died and I'm now completely unable to port forward. I follow all the steps to port forward but alas the port is still closed every single time. I've tried a few fixes in the past including disabling UPnP, using those auto port forwarding programs, and creating an exception for the port in my fire wall. Nothing has worked!
View 14 Replies View RelatedCisco Firewall :: 5510 - Opening Ports For Video Conferencing?
Nov 7, 2011We have just acquired a cisco profile 42 video conferencing equipment and am required to open ports for SIP and H232, any pointers on hw that can be acquired i have a cisco ASA 5510, Some one told me to open port 16384 but i need pointers on how to do it becuase I already set an access list to any.
the config
Internet -> ASA 5510 -> Switch -> Profile 42 and other devices
Cisco Firewall :: 5505 - Opening TCP Ports In ASDM Launcher
Jun 20, 2011 I am trying to open up 3 TCP ports in Cisco ASDM Launcher:
16000
16001
8098
And have a Cisco ASA 5505 Router. I need these ports open in order for a software that I have installed on the server to communicate with my local client computers for my business, The software is installed on Windows 2008 Server Standard Edition and was installed with MicrosoftSQL 2005. The software and Microsft SQL 2005 is pretty much installed and just requires this last step in order for the server to be connected to the local computers. In order to resolve this, I have gone to.
Cisco Firewall :: 5505 - Opening Ports On DHCP Outside ASA Interface
Feb 25, 2011I am used to setting up access-lists on outside interfaces with ip addresses that are static. I have recently been given a site that is using a dyndns.org client for name to ip address resolution on an outside interface that is dhcp assigned. I created an access-list to open up ports 41794 and 41795 to an engineering application but everytime I try to connect from the outside I get a syn timeout. The application works when inside the lan. Basically I want to allow outside connections from anywhere on the outside to go to ports 41794 and 41795. I am running a Cisco ASA 5505 on version 7.2(4) Below is my conifg. what I may have misconfigured?
: Saved:ASA Version 7.2(4)!names!interface Vlan1 nameif inside security-level 100 ip address 172.31.2.1 255.255.255.0!interface Vlan2 nameif outside security-level 0 ip address dhcp setroute!interface Ethernet0/0 switchport access vlan 2!interface
[Code].....
Linksys Wireless Router :: Ports On Ea4500 Not Opening
May 25, 2012I just purchased a cisco ea4500 I have set up port forwarding for http, https, rdp. however when I run zenmap and port check it fails says port in use. I have set it up in sigle port forwarding, rang and port trigging. I tried RDP and VPN to machine that is hard wired and it fails as well. My windows server is connected as well however RDP fails on there to
View 9 Replies View RelatedCisco Switching/Routing :: Simple Way Of Opening Ports On 1841 Router
May 12, 2012Any simple way of opening ports on a 1841 router.I have a working config for internet traffic. I am looking to boot up my Windows Server and Run IIS.
View 1 Replies View RelatedD-Link DIR-615 :: Opening Ports For Server Applications Like Ventrilo / Filezilla?
Mar 10, 2011I've installed XAMPP on one of my Vista computers, and intend to use it as a server. The internal IP address of the server is A.B.C.D. The internal IP address of the DIR-615 is A.B.C.E. whatsmyip.com says that external address of the server is F.G.H.I (and so is everything else inside my network). I have Filezilla listening on port 21. I've turned Windows Firewall completely off on the server, and my ISP (Time Warner / Road Runner) says that they never block any port.I tried going to the DIR-615 using Port Forwarding, and set ports 21 & 90 to forward to A.B.C.D, for both UDP & TCP, Allow All, Always. That didn't work.I tried going to the DIR-615 using Virtual Server. I set a virtual server on port 21 to A.B.C.D, for both UDP & TCP, Allow All, Always. It made me turn off Port Forwarding, and it wouldn't let me use both 21 & 90 on the same rule, so made two rules. That didn't work either.
I tried setting A.B.C.D as a DMZ host. That still didn't work.I can ftp connect into A.B.C.D from one of the other computers in the network. People outside the network can't connect to F.G.H.I. I can't connect to F.G.H.I. from inside the network. The same is true of Apache (but ports 80, 81 & 443), Ventrilo (but ports 3784 & 6100) and MySQL (but port 3306). I figure that FTP is the easiest to test, so I've been just trying to get that to work.In FileZilla Server Options, I am bound to *, I have no filters, and my passive mode is set to "Retrieve external IP"As far as I can tell, if I've ruled out anything inside my network (by connecting internally), and I've ruled out my ISP (they don't block), then it must be the router. I think I've done port forwarding according to [URL], and it seems like it should be easy, but I've been trying forever and I can never get it to work.
Belkin Routers :: F5D8233-4 V3 / Opening Ports 1701 And LT2P
Dec 4, 2012I have a Belkin F5D8233-4v3 N Wireless Router. To get the wireless Directv connection, directv told me I have to get 2 ports open on my router.1701 and LT2P.
View 1 Replies View RelatedLinksys Wireless Router :: WRT54G2 - Port Forwarding Not Opening Ports?
Nov 20, 2011I have a cable modem hooked up to a Linksys WRT54G2 wireless router, which is hardwired to the computer I use.
I go into the router's menu by going through the standard 192.168.1.1 in the browser, and then go to Applications and Gaming. The port I am trying to open is port 25565 for both TCP and UDP. In the Start and End ports I put 25565, and for the end of the IP Address, I put the last digits of my IPv4 address (10). I used a couple of port checker tools, and it is reporting as still being closed.
D-Link DIR-655 :: Ethernet Ports Don't Seem To Work
Feb 8, 2013i've tried plugging in various devices (computer & solar panel management device) into the ethernet ports to no avail. i just updated the firmware, reset the router, and still no luck. all of the lights work when i reset and the wifi works fine. do i need to do something in the settings to turn on the hard connection?
View 3 Replies View RelatedCisco :: ACLs To Limit Ports With Client - Based VPN Tunnel
Jun 16, 2011I have a customer I've built a webvpn tunnel for.Users on this tunnel need to have http access to a server at 10.1.1.12 and nothing else.That's fine, but in order for name resolution to work properly they need to be able to send DNS requests to 10.1.1.9.I'm working with two different access lists, my non access list (nat 0) and my split tunnel access list. I can't specify ports in the nat 0 access list, but I did try writing my split tunnel access list as follows:
-access-list split permit ip host 10.1.1.12 172.16.4.0 255.255.255.0
-access-list split permit udp host 10.1.1.9 eq 53 172.16.4.0 255.255.255.0
When I do that users can access the 10.1.1.9 dns server, but they can hit it on anything (ping, 3389, etc.).I'm trying to figure out how I can limit them so they will only be able to pull dns but nothing else.They have the Any connect Essentials license, so unfortunately a clientless VPN is not an option. Is there some other access list I can interpose that will limit things the way I want?
Cisco WAN :: WRV210 Not Work With SMB Series SG 100 16 Ports Switch
Jan 19, 2011I connect a WRV210 router with Small Business 100 Series Unmanaged Switch SG 100-16 Switch. But the switch is not work with the router.In the port of switch (connect with router), no light. In router, the port is disable.Do I need cross-over ethernet cable connect with them?I tried connect WRV210 directly to computer, that is work. I tried connect WRV210 to other (no name) switch and connect this switch with Cisco Switch 100-16 switch than they are work. why?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Using SFTP Option In ACS 5.3?
Mar 25, 2012Any problem while using SFTP option in ACS5.3.I am trying ot use host-key sync command but giving below error.
ACS/admin(config-Repository)# host-key sync
% Error: First character must be a letter
% Error: Invalid ip address or hostnameSOK-S12-ACS-1/admin(config-Repository)# host-key sync% Error: First character must be a letter% Error: Invalid ip address or hostname
As per documentation this command needs to be added directly.
SFTP Connection Failing?
Dec 4, 2012I set up a connection from a laptop (Windows 7) that goes through a LAN proxy server to a secure ftp server (Windows Server 2003).The sftp server is assigned a public ip address.I opened the firewall at the destination and allowed port 22 traffic to the sftp server. Well, the connection is failing.I know for a fact the connection from the client laptop is making it to the sftp server.If I issue this command on the client laptop:
telnet sftpserver 22
The DOS screen clears and tells me the type of SSH server I'm connecting to. While this connection is still active, I logged into the destination sftp server and did a netstat command. I can see the address of the proxy server in the "Foreign Address" column of the netstat results. I also can see the proxy server address when I look at the Application Log on the sftp server, so I know the connection is making it to the sftp server.
I beleive the problem is the control port (return traffic) from the server back to the client. Something is being blocked or is misconfigured. I always thought the router negotiated the control port, and that the control port didn't need to be put into any firewalls.
Need Recommendation For SFTP / SSH Application
Dec 13, 2012There are many software available for this but the issues is how they all function. Example: One software Synchronized FTP allows you to set a local/remote folder and sync files between them. What was never disclosed is that you need Windows Task Scheduler to run the synchronization, and you do not see a progress indicator. I also tried TurboFTP but it felt like landing a space shuttle.
View 8 Replies View RelatedRun BAT File Remotely Through Sftp In GUI?
Aug 25, 2012how to actually run a .bat on a remote computer through ssh/sftp in a GUI. My problem is that I havent been using command lines for 15 years, I litterally have never used a command line besides using stuff like ipconfig in command prompt.I have a ssh server on my home server using FreeSSH'd and The only ssh program i can find with a gui is winscp. Though theres no option to connect through ssh everyone says it does and theres even options for it.
Though when i try to run the bat file i get this error"Current sftp -3 session does not support command you request" then something about a seperate shell session. if i click ok it goes down to starting the session then just sits there and says host is not communication for more than 15 seconds still waiting and only option is to abort.
Cisco VPN :: ASA 5510 - Does Client Work With ACS
Oct 30, 2011I woudl like to ask all of you that i have ASA 5510 and i want to do VPN client authetication with LDAP, after verify username and password with AD and it use policy with ACS?
View 3 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.x - Unable To Backup By SFTP
Apr 5, 2011I am not able to backup ACS 5.x server by means of SFTP protocol. We use ACS 5-2-0-26-2. My configuration of repository is:
repository SFTP
url sftp://x.x.x.x/home/user
user user password hash 455ad
command 'backup acs01 repository SFTP' does not work and I receive the following error message on ACS server:
%SSH connect error
On my sftp server I can find the following error messages:
Apr 6 06:57:46 CR01 sshd[8561]: Accepted password for user from 10.20.86.72 port 47924 ssh2Apr 6 06:57:46 CR01 sshd[8563]: Received disconnect from 10.20.86.72: 11: disconnected by user
How to successfully performed backup by means of SFTP protocol? Do I need any other configuration settings except repository? Do I need to store my SSHD RSA key to ACS? I am able to copy files using SFTP from other computers, so it seems that SFTP server is set correctly.
Cisco VPN :: Does VPN3005 Work With AnyConnect SSL Client
Sep 27, 2012Does VPN concentrator "VPN3005" work with AnyConnect SSL VPN client?
View 3 Replies View RelatedCisco VPN :: 7800N / Connecting From Client To Work VPN?
Dec 8, 2012I recently picked up a Billion 7800N home router to replace my old netgear which was dropping signal alot.I seem to have develpoed a problem accessing my work network through the VPN client. I am able to connect the Cisco VPN client to the network ok but I don't have any access to the server and exchange email. I have tested the client settings on my old Netgear and it is working fine. This points me to the direction of the router....I don't have any packet filtering on and I have set up profile from my fixed internal home ip to the work ip to allow any protocol and any port.I have also port forwarded 500, 4500 and 10000UDP to my internal ip address.
View 4 Replies View RelatedWireless :: Format Hard-drive And Reinstall XP Pro / USB Ports Don't Work?
Jan 2, 2012Purchased desktop from micropro in 2002. We finally upgraded to cable internet in 2011, Wife purchased Think Pad laptop also in 2011 (wireless enabled). Purchased Belkin wireless router and want to network these 2 computers.1. My desktop has been demoted to the garage. I have wiped it clean (i hope) by doing a reinstall of XP Pro. Now some of the USP ports won't work. How do I network these two machines?
View 1 Replies View RelatedLinksys WRT54G When Plug Any PC Into Ethernet Ports It Doesn't Work
Feb 1, 2011I have the Linksys WRT54G Wireless Router, when i hook my at&t modem to the modem port on the router the wireless portion of the router works, when i plug any pc into the Ethernet ports it doesnt work!If i plug the modem into the Ethernet port and plug other pcs into the other existing Ethernet ports it works by Ethernet but not wireless.
View 1 Replies View RelatedSharing :: SFTP File Transfer Is Slow?
Apr 7, 2011i am running windows server 2008 with the hyper V role installed.i have installed windows 7 Professional as a guest OS. assigned 2 GB of Ram to the machine. the point behind the VM is to virtualize my FTP server and incase a format is required i have the VM file on my 2nd partition, host OS on another. i use Cerberus FTP Server on the Win7 OS. i configured the server to accept SFTP and TLS connections. on the host OS i installed Fire FTP and File Zilla, both Clients will at max download a 4 MB file at 64 KB/Sec .. i have seen both jump to about 80 KB but was only a split second and never held.. however if i login without SFTP and transfer over standard protocol, i download at 1 MB/sec. which is my normal speeds. would this be only to the encryption process?, in the Cerberus Server there are options to adjust download speeds, i have left it default, and altered it to allow its max configuration. My ISP is not limiting any connections that shouldnt be.
View 1 Replies View RelatedCisco Routers :: WRVS4400N - Server Certificate To Get VPN Client To Work?
Dec 12, 2011WRVS4400N Where is the Server Certificate located to get the VPN Client to work?
View 2 Replies View Related