Cisco Switching/Routing :: 2950G Series Not Communicate With HP Switch?
Feb 3, 2013
I have mounted a cisco 2950G series switch in the network. we are working on Multicasting so I have LAN connectivity from one location ot other.
Situation:- 1- we do not have to do anything at remote location. its already done with final configuration and working fine because we other location witch are connected with this same HP switch at remote site and working fine but problem is only with one location where I have changed switch(cisco2960). when i connect cable from MUx to the switch cisco switch (Local) on particular port its does not response (LED continuously glowing amber color and does not go to green color) and communication does not start.for fixing this issue I have done so many things, vlan, duplex, speed- done everything but response.
situation 2:-when I changed this cisco device and use any other vendor's switch whether its manageable not manageable its get start proper communication. so I am unable to figure out whats the issue with. is there new or latest switch are not compatible with other vendor.
View 1 Replies
ADVERTISEMENT
Jul 20, 2011
getting radius to work on a 2950G switch with an older IOS of 12.1(22)EA1. I have radius setup on a windows 2k8 box and all of my other switches 2960's and above have no issues. I am unable to input the nas-identifier of 32 into the config using - radius-server 32 attribute 32 include-in-access-req format %h as well as the aaa session-id common commands. Doing a debug radius says that the radius server is not defined.
View 5 Replies
View Related
Sep 11, 2012
Cisco 3750, I'm trying to reset the password but cannot communicate with my switch
View 1 Replies
View Related
Jan 3, 2013
Got 2 pcs. of C2950G-24-EI which are both running 12.1(9)EA1. Now I was thinking to upgrade them to the latest available (12.1.22-EA14), but before I do this task I'd like to know if there's a way to check in advance if those images will run. Any way to check about available memory or memory needs?
View 8 Replies
View Related
Mar 28, 2012
I have a Catalyst 2950G when I activate the switchport port-security, but I want to empty the black list of mac address because every time I connect a device, the port is automatically désacative, here is the port configuration:
!
interface FastEthernet0 / 2
switchport access vlan 17
switchport mode access
switchport voice vlan 51
[code]....
I tried the following commands to clear the blacklist mac address of that port, but the problem is still relevant:
# Clear mac-address-table dynamic int fa0 / 2
# clear port-security all int fastethernet 0/2
# clear errdisable interface fa0 / 2 vlan
View 17 Replies
View Related
Oct 14, 2012
I have a routed interface on a Cisco 6500 Series switch. I am trying to find a way to adjust the tcp mss.To date I have not yet been able to find a way to accomplish this. Is this just not supported?
View 3 Replies
View Related
May 13, 2012
We are using cisco ME 3400 E series switch. Which port we can use as CFM port ? We configured CFM in gig port.Is all the ports will act as CFM port or any separate CLI command is there for enable ?
View 0 Replies
View Related
Apr 1, 2013
We are facing cold start issue on 4500 series switch. The switch is restarting automatically almost weekly twice or thrice.As per show tech. output , there is "cold start log".Please find the attached logs for your reference.After time change , auto restart happening & am not found any log for power failure also.
View 6 Replies
View Related
Sep 17, 2012
When i connect two cisco 2960 series switchs via stright trough cable causes delay in transmission sw1 has vlans and having trunk port connected to router all vlans are able to access internet sw2 is connected to vlan5 on switch1 sw2 has factory default configuration computers on sw2 can access internet but I have low bandwith problem on sw2 there is transmission delay problem?
View 1 Replies
View Related
Apr 19, 2009
How to change ip address in cisco 2960 series switch?
View 4 Replies
View Related
Oct 14, 2012
We have a 4500 series switch that is running around 39% cpu utilization but seems to be dragging a bit. I did a show platform health and GalChassisVp-review has a target of 3% but an actual of 17%. All other actual values were at or below target values. I then went to show platform cpu packet statistics and in the "Packets received by Packet Queue" all queue packet values at 5 sec, 1 min, 5 min and 1 hour avg were either 0 or 1 with the exception of Esmp - that averaged 351/377/317 and 313 respectively. I then checked show platform hardware acl input entries static and the entry type InputEsmpToCPU had a whopping 10121370 hit count. All other entry types were well under that number.
View 2 Replies
View Related
Mar 5, 2013
Suddenly my 2960 D series switch went offline and i founf the switch was not powering. I can't figure out the issue.
View 3 Replies
View Related
Feb 14, 2012
does Cisco 2600 series switch support 802.1x and DHCP snooping?
View 6 Replies
View Related
May 16, 2013
We are working with a contractor to upgrade our network, and I heard from them that the 5596/5548 might not need the Layer 3 module for our inter-VLAN routhing. They have yet to give me an answer.
We do have a few static routes on our current layer-3, core switch too.
View 3 Replies
View Related
Apr 23, 2013
I want to limit the bandwidth of my Catalyst 3750 series switch, I read the cisco documentation and I applied the commands but I didn't get the wanted results.
For the outbound traffic it's ok, but for the inbound traffic I used policing but I get an unstable traffic. I used, an access list and a class-map to classify the traffic and then a policy-map.(I followed the steps mentioned in this site: [URL]
View 4 Replies
View Related
Nov 4, 2012
we are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950
S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end
3750
SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
View 1 Replies
View Related
Feb 5, 2012
I have a new Cisco 2960 S series switch with a basic configuration that needs to be uplinked or daisy chained to a Cisco 3750 switch. I am not getting any connectivity to the network with either a straight through or crossover cable. the port remains in amber but a 'show interface' indicates that the interface is up. I can manage the switch with a PC patched into any port on the switch with a static IP address. Must be something very simple that I am missing. Outlined below is the configuration.
Refresh_SW1#sh ver
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3,
RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
View 8 Replies
View Related
Apr 7, 2012
My problem is that I have a Cisco 300 series small business switch with multiple VLANS each one with an IP address and two or three ports assigned to each VLAN. I have an E3200 wireless router that I want to use to use to share internet on the switch. All of the VLANs are reachable from the other VLANs and I've put a static route on the E3200 so that I can reach the VLANs from a machine connected only to the router. But I can't reach machines on the otherside of the router or get to the internet from the switch.
View 3 Replies
View Related
Jan 28, 2013
Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
View 9 Replies
View Related
Sep 24, 2012
We have acquired few AIR-BR1410A-A-K9 AP's that are for US only. I am in Pakistan. For our market, Cisco proposed AIR-BR1410A-E-K9. This is fine as it is listed on their website as well.However, since we also have the "A" model and now the "E" model, can we place an A model on one end and an E model on the other and make them communicate with each other?
View 3 Replies
View Related
Feb 12, 2013
I was asked to configure a new ASR 1002 today and after successfully puttintg the config on the router (via TFTP) the router will no longer communicate with anything. There is nothing in the config to cause this (it was actually pulled off a working production ASR 1002) and I am unable to ping a local loop back IP while consoled into the router?? I removed the config, reloaded the router and configured a new loop back - same issue cannot ping the loop back or anything else connected to this router.
View 7 Replies
View Related
Oct 22, 2011
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
View 6 Replies
View Related
Nov 13, 2011
Will ACL110 allow IP phones communicate with VoIP server. Do I need to add line to allow multicast traffic? [code]
View 0 Replies
View Related
Apr 6, 2012
I have a Nexus 5548 installed (layer 2 device only) with several 10G ports supporting IBM P770 systems and a TSM (Tivoli Storage Manager) system on a single VLAN. All of the Nexus 5548 ports are configured for jumbo frames. I was ask to install a new server on the same VLAN as the others but as 1G port without jumbo frames to allow communications with the TSM server. I'm assuming that the 1G port for this new server without jumbo frames configured on the Nexus 5548 will not be unable to communicate with the TSM server that is on the same VLAN with it's Nexus 5548 10G port configure using jumbo frames.
View 5 Replies
View Related
Feb 9, 2012
A brand new network switch how i check this network switch on may pc how to communicate this switch very 1st time with pc
View 3 Replies
View Related
Oct 27, 2012
How is it possible to configure 2 VLANs to communicate with each other on the same switch? I have managed to create 2 VLANS and they both work (and can access the internet), but they can't communicate with each other.VLAN1 has an IP range starting 10.4.160 and VLAN2 has an IP range starting 10.6.192.Is it VLAN routing that I'm looking for? My switch is Netgear GSM7328FS.
View 1 Replies
View Related
Jan 24, 2013
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies
View Related
Mar 19, 2013
I have peculiar challenge ahead of me and would like to get new perspectives.
The objective is to route specific VLAN traffic and the caveat is that I have multiple VLANs with the same network address.
For example:
VLAN100 10.10.10.0/28 VLAN101 10.10.11.0/28 VLAN102 10.10.12.0/28
VLAN103 10.10.12.0/28
VLAN104 10.10.11.0/28
I need traffic going from VLAN100 with a destination of 10.10.11.0 forwarded to VLAN101 and NOT VLAN104.
This task is currently being completed by a multi context firewall and we're trying to decommission the asset.
View 5 Replies
View Related
Oct 30, 2011
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies
View Related
Sep 16, 2012
i have one sonicwall NSA 240. it is directly connected to ISP and other interface connected with cisco Layer 2 switch. my que. is that. how to access that sitch remotely ??
sonicwall 1st interface connected with ISP (pubilc IP) and 2nd interface connected with cisco switch with private IP bocz there NAT configuration. i m able to access sonicwall and i m getting ping up to sonicwall bt i cann't able to ping cisco switch.. i think some i need a some missing in sonicwall configution like telnet or VPN
View 1 Replies
View Related
Jun 17, 2012
It is my understanding that the FWSM for the 6500 series switches uses a 6 port Etherchannel on the backplane to communicate with the 6500 series switch.Can you shutdown vlan1 on the switch and still communicate with the FWSM? I was under the impression that you could not (although I am looking at a config with it shutdown)
View 1 Replies
View Related
Jun 1, 2013
Configuring an application using routing mode on cisco ace clients ---asa--3750--cisco ace--- servers behind vip,visa card transaction servers.i am able to setup a vip on ace using routing mode on ACE,as the servers need to see the client ip ,so we are not performing SNAT,this part is working fine,when a request comes from the client ,it goes to the vip and to one of the backend servers ,and the request will be forwaded back to the ace ,as the default gateway on the servers is pointing to the server vlan on ace.but if the transaction from the servers need to go to the visa card transaction servers ,how can we achieve this ,and after fetching the data from visa servers,does the reply will be fwd to the ACE or ASAs directly.
View 1 Replies
View Related
May 14, 2013
I need to choose router for my network. I don't have any special need, besides Internet connection and DHCP for some guest clients.There are around 30 IP phones (static IP), 30 PCs (static IP), and 10 wireless APs (users get dynamic IP). Maximum load is 5 phones, 5 PCs and 20 phones/laptops connected via wi-fi.
I guess I should go for Cisco 800 series. Would model 861 be good or I will need 881 or even 891?
View 3 Replies
View Related
