I need to choose router for my network. I don't have any special need, besides Internet connection and DHCP for some guest clients.There are around 30 IP phones (static IP), 30 PCs (static IP), and 10 wireless APs (users get dynamic IP). Maximum load is 5 phones, 5 PCs and 20 phones/laptops connected via wi-fi.
I guess I should go for Cisco 800 series. Would model 861 be good or I will need 881 or even 891?
how to setup 802.1x on the Cisco 500 Series Switches.I have done the whole implamentation in the past with Catalysts and ACS.But would like to see a guide for the 500 series.Do we need the Cisco ACS or can we use RADIUS on Windows?
View 1 Replies View RelatedI have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?
View 1 Replies View RelatedI have the following on my 6509:
Mod Port Model Serial # Versions
---- ---- ------------------ ----------- -------------------------------------
1 10 WS-SVC-WISM-1-K9 XXXXXXXXXXX Hw : 2.2
Fw : 12.2(14r)S5
Sw : 12.2(18)SXF16
Sw1: 8.6(0.306)R3V39
WS-SVC-WISM-1-K9-D XXXXXXXXXXXX Hw : 2.1
There are few documents that tell me different requirements for the WISM cards to configure VSS.
I have a cisco 1941 router. Stock standard vanilla hardware, no extras. Standard universal image. Data and Security not enabled.I would like to add a 4 gigabit port POE switch (EHWIC) module to the router..The 4 port POE switch module will be used to power and connect 2 x Areonet AP's for my home. I'm replacing a Apple Airport Extreeme and Express setup. I'll possibly later use the two remaining POE ports for security cameras.My question is, what extra hardware and or IOS version do I need for the POE swtich module to function on the 1941? [URL] I think this is the model I want EHWIC-4ESG-P #4 port 10/100/1000 Enhanced High-Speed WAN Interface Gigabit Ethernet switch with Power over Ethernet?
View 1 Replies View RelatedI want to chose the right UPS product for 7 x WS-C3750X-48PF-L in one stack. The Cisco data sheet says 1100W AC, however, I am only connecting 20 IP Phones, each phone will consume around 12.2 Watts.
So in this case, How many watts would I need for the whole 7 switches in the stack ?
in other words, only the first switch in the stack will be connected to 20 IP Phones, but the remaining switches in the stack will be Data Only thought the remaining switches in the stack are capable of delivering a full PoE.
the power consumption of the WS-C3750X-48PF-L with only data connected to it.
We are planning to replace a few line cards in the existing 6509-E chassis. The sup installed is a VS-S720-10G-3C but the line cards are legacy. As a result we are not able to enable the VSS functionality. We are looking to replace the existing line cards with the following:
1. 1 x WS-X6716-10G-3C
2. 1 x WS-X6724-SFP
3. 4 x WS-X6724-GE-TX
What are the requirements in terms of IOS and Roman.
The current IOS is: Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
And the ROM Version is: ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
Do I need an upgrade?
I am calculating Cisco 4500X power consumption requirements to select appropriate UPS systems. I have 4500X switch with dual power supplies.which value should I take for power consumption calculation, in data sheet it has two values: AC Power Max Rating: 750W System Power Consumption: 330W nominal/400W max
Which values should I take, to calculate UPS systems capacity? And also I am interesting when 4500x has two power supplies what is power consumption?
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI have peculiar challenge ahead of me and would like to get new perspectives.
The objective is to route specific VLAN traffic and the caveat is that I have multiple VLANs with the same network address.
For example:
VLAN100 10.10.10.0/28 VLAN101 10.10.11.0/28 VLAN102 10.10.12.0/28
VLAN103 10.10.12.0/28
VLAN104 10.10.11.0/28
I need traffic going from VLAN100 with a destination of 10.10.11.0 forwarded to VLAN101 and NOT VLAN104.
This task is currently being completed by a multi context firewall and we're trying to decommission the asset.
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies View RelatedConfiguring an application using routing mode on cisco ace clients ---asa--3750--cisco ace--- servers behind vip,visa card transaction servers.i am able to setup a vip on ace using routing mode on ACE,as the servers need to see the client ip ,so we are not performing SNAT,this part is working fine,when a request comes from the client ,it goes to the vip and to one of the backend servers ,and the request will be forwaded back to the ace ,as the default gateway on the servers is pointing to the server vlan on ace.but if the transaction from the servers need to go to the visa card transaction servers ,how can we achieve this ,and after fetching the data from visa servers,does the reply will be fwd to the ACE or ASAs directly.
View 1 Replies View RelatedI've goggled and searched here, and I can't seem to find what I'm looking for. I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.
View 2 Replies View Relatedhow to configure Qos on Cisco ME 3600X Series switches. As I tried Mls Qos and it wont have these commands.
View 1 Replies View Relatedabout to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.
View 5 Replies View RelatedI have a Cisco 800 series router that I need to set NAT up on. There will be four computers connecting to the internet through it. I already have the IP address coming from my cable modem I just do not know the command to get it to translate to my internal dhcp pool I have setup.
View 1 Replies View Related: %DATACORRUPTION-1-DATAINCONSISTENCY: unterminated string in buffer of length 129, counted: 129 -Traceback= 4027CB2C 402B1E88 4052884C 40528A48 40528D08 40529188 40529358 403247E8 403247D4
Cisco Internetwork Operating System Software
IOS (tm) C5RSM Software (C5RSM-ISV-M), Version 12.2(46), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Thu 26-Apr-07 19:41 by pwade
Image text-base: 0x40010948, data-base: 0x410F41D0
[code]....
I'm trying to turn off SSH version 1 & 2 to pass PCI compliance. Problem is, I cannot touch the VPN link between the two offices. I'm afraid the PKI certificate used for the VPN will be deleted if i zeroize the RSA key which seems to be the only way to stop the router responding on port 22.
Here is the stuff from the running config related to the crypto map:
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
[ code].....
I'm only CCNA so I'm not even sure if the certificate or RSA key is being used for the VPN link, but I can't tell from the running config that zeroizing it would be a good idea and not break the VPN. I'm open to other ways of disabling SSH, as we are able to just connect using a console cable. But it looks like denying port 22 with an access-list doesn't even stop the router from responding to the port.
If a Supervisor 6-E will support NetFlow on a Catalyst 4507R-E?If not, what are my options for NetFlow on a 4507R-E?
View 7 Replies View RelatedI can see the console on the router. (Using the USB console connected to a Macintosh.) I was configuring the router though this console connection, and I created a new user (priv level 15) and removed the default 'cisco' user. So I'm stuck at the username/password login prompt now.
I decided to do the password recovery procedure (via the cisco doc I found etc), but I cannot break into ROMMON during the boot process. I'm not sure if that's because my Mac isn't sending the break, or what.
The pw recovery doc says you can "remove flash" if you can't break into the boot sequence. However, I cannot find any instructions on how to remove the flash. I've opened the router, and I see one very small daughter card on the main board that I think is the flash, but I'm not about to start arbitrarly prying parts off.
My Cisco seems to be stuck when it boots up, with the following:
Upgrade ROMMON initalized
And it goes on with self comperessing image then an OK but then it starts loading again all over.
I have a routed interface on a Cisco 6500 Series switch. I am trying to find a way to adjust the tcp mss.To date I have not yet been able to find a way to accomplish this. Is this just not supported?
View 3 Replies View RelatedWe are using cisco ME 3400 E series switch. Which port we can use as CFM port ? We configured CFM in gig port.Is all the ports will act as CFM port or any separate CLI command is there for enable ?
View 0 Replies View Relatedwe are using cisco 6509 series switches as core switches. and Cisco 4510,4507 series switches as edge switches. all the vlans are created at core switches and propogating to edge switches through VTP. we are using OSPF as routing protocol at core switch for internal routing. till now we are using 4510,4507 switches as layer 2 switches. Since, 4510 & 4507 switches are hign end swithces i want use them as layer 3 switches instead of layer 2.if i change these switches from layer 2 to layer 3 does it make any impact on our network or better to keep them as layer 2 switches.if i change these switches to layer 3 is there any advantage i will have.
View 3 Replies View RelatedI have Router 2800 series Global nating is configured on it.
ip nat inside source list 111 interface Dialer1 overload
!
access-list 111 deny ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
My object is that i want give internet access only for few users ip E.g IPs addresses from range 192.168.1.0-10 can acess intenet access other all are deny.How i do this with ACL .
I would like to setup RDP on my cisco router so I can access my server from outside my network. I also have a router from my ISP that has DHCP for my external IP address and DHCP for my internal as well.
View 3 Replies View RelatedIn an attempt to restore a Cisco IOS I deleted the file C2960-lanbasek9-mz.122-53.SE2.bin my swich
Before deleting the same was as follows:Directory of flash :/
3-rwx 12824 Mar 28 1993 21:00:37 -03:00 vlan.dat4-rwx 3096 Mar 7 2012 08:43:37 -02:00 multiple-fs5-rwx 2289 Mar 7 2012 08:43:37 -02:00 private-config.text6-rwx 7482 Mar 7 2012 08:43:37 -02:00 config.text9 drwx 192 Mar 23 2012 16:18:54 -03:00 C2960-lanbasek9-mz.122-53.SE2
32514048 bytes total (20204544 bytes free)Switch-01 #
Right now this switch as follows:
switch: dir flash:Directory of flash:/
2 drwx 64 <date> crashinfo_ext 3 -rwx 4120 <date> multiple-fs 5 -rwx 12824 <date> vlan.dat 6 -rwx 4018 <date>
[Code].....
I have a Cisco 800 series router that I need to set NAT up on. There will be four computers connecting to the internet through it. I already have the IP address coming from my cable modem I just do not know the command to get it to translate to my internal dhcp pool I have setup. I have also been doing some research, seeing as I only have one public IP address coming from my ISP will I have to use PAT as well?
View 1 Replies View RelatedI have a Cisco 881 router running 15.1(4)M4. I am trying to configure SPAN on it to mirror my outside interface (source) to one of my LAN interfaces (dest).
!--- WAN interface
interface FastEthernet4
description Comcast WAN$ETH-WAN$
[Code]......
As you can see from the above output there is a problem with the command on this interface. When I try to set Fa0 as my source it works fine:
rtr(config)#mon session 1 source int fastEthernet 0
rtr(config)#
Is this because fa4 is layer 3 and fa0 is a switchport? If so, is there another way to set fa4 as the source?
I have mounted a cisco 2950G series switch in the network. we are working on Multicasting so I have LAN connectivity from one location ot other.
Situation:- 1- we do not have to do anything at remote location. its already done with final configuration and working fine because we other location witch are connected with this same HP switch at remote site and working fine but problem is only with one location where I have changed switch(cisco2960). when i connect cable from MUx to the switch cisco switch (Local) on particular port its does not response (LED continuously glowing amber color and does not go to green color) and communication does not start.for fixing this issue I have done so many things, vlan, duplex, speed- done everything but response.
situation 2:-when I changed this cisco device and use any other vendor's switch whether its manageable not manageable its get start proper communication. so I am unable to figure out whats the issue with. is there new or latest switch are not compatible with other vendor.
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies View RelatedWhat is the installation time for the Network Processor engine is:
NPE-G2=7200 series NPE-G2 engine with 3 GE/FE/E ports ,Do you reckon it can be done in two hours?
I have a 2600 Router series and I cannot remember the Password. I have tried following web pages that state to use control Break on the boot up but its not working.can reset that pw and write erase my configuration file?Here is my boot up. I have tried hitting control break at the very beginning over and over and then again when at the cold boot it has not worked....
System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)Copyright (c) 2002 by cisco Systems, Inc.C2600 platform with 131072 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x1c9468cSelf decompressing the image : ######################################################################################################################################################################################################################################################################################################################################################################################################################################################################## [OK]
Smart Init is enabledsmart init is sizing iomem ID MEMORY_REQ TYPE00036A 0X000B3B80 C2610XM Single Fast Ethernet 0X00098670
[code]....