Cisco Switching/Routing :: Setup RDP To A Server On 800 Series Router

Dec 27, 2012

I would like to setup RDP on my cisco router so I can access my server from outside my network. I also have a router from my ISP that has DHCP for my external IP address and DHCP for my internal as well.

View 3 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Setup Port Forwarding On 800 Series Router?

Jan 14, 2013

I just setup my homelab today, after having Cat5e installed so I can run my servers and network equiptment over wired network as well as setting up a wireless system.  I got everything setup and its going great I can access everything from my office now including a E4200 Linksys router that I setup to do RiP (was only choice pretty much, or NAT), and my 891 Cisco Router which is my internet connection.
 
I use to have the linksys setup to do port forwarding but now I need to figure out how to do it on the cisco 891 router via command line.
 
Below is my current configuration.  I need to be able to access my server which is behind my router by Remote Desktop.  I also have a web server, and the kids also play minecraft, and have a server setup so I need to be able to forward their port as well.
 
[URL]
 
Ths is from the link above, would I just do like that but then put in my IPs and is that my Private IP I use this or my public facing.   Also he has "interface Dialer1 6881" again after the port in the second and third row.  I dont really understand what they have there.  I understand basic access list and such though I am extremely rusty. 

!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.0.0.2 6881 interface Dialer1 6881

[Code].....

View 14 Replies View Related

Cisco Switching/Routing :: Does The 22xx Series FEX Support Static Or Dynamic LAGs Between Itself And A Server

Nov 18, 2012

Does the 22xx Series FEX support static or dynamic LAGs between itself and a server?Imagine a server with dual 10G NICs, and I need to connect them to the SAME 22xx FEX....can I set up a LAG between the two 10G NIC ports and two 22xx FEX Host ports? Does it depend on how the FEX is connected to the parent 55xx?

View 0 Replies View Related

Cisco Wireless :: WLC 2500 Series Setup With Windows Server 2008 R2

May 15, 2011

I am planning to implement wireless network in my work place. Plan is to have two networks one for guests and one for employee. I am trying to find a guide for 2500 WLC but couldn't find one.I've been reading couple of articles about setting up radius server and CA. I want to know what the best way to approach this.In my environment I got a CA server windows server 2003 and current DC's are windows server 2008 R2.I got 2500 WLC with POE switch and 4 aironet AS 1142.

View 16 Replies View Related

Cisco Wireless :: WLC 2500 Series Setup With Windows Server 2008 R2

Jun 27, 2012

I am planning to implement wireless network in my work place. Plan is to have two networks one for guests and one for employee. I am trying to find a guide for 2500 WLC but couldn't find one.
 
I've been reading couple of articles about setting up radius server and CA. I want to know what the best way to approach this.
 
In my environment I got a CA server windows server 2003 and current DC's are windows server 2008 R2.
 
I got 2500 WLC with POE switch and 4 aironet AS 1142.

View 4 Replies View Related

Cisco Switching/Routing :: 800 Series Router Configuration

Jun 13, 2012

about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.

View 5 Replies View Related

Cisco Switching/Routing :: Setting Up NAT On 800 Series Router

Aug 23, 2012

I have a Cisco 800 series router that I need to set NAT up on. There will be four computers connecting to the internet through it. I already have the IP address coming from my cable modem I just do not know the command to get it to translate to my internal dhcp pool I have setup.

View 1 Replies View Related

Cisco Switching/Routing :: NATing On 2800 Router Series

May 22, 2013

I have Router 2800 series Global nating is configured on it.

ip nat inside source list 111 interface Dialer1 overload
!
access-list 111 deny   ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
 
My object is that i want give internet access only for few users ip E.g   IPs addresses from range 192.168.1.0-10 can acess intenet access other all are deny.How i do this with ACL .

View 2 Replies View Related

Cisco Switching/Routing :: Setting Up NAT And Possibly PAT On 800 Series Router

Aug 23, 2012

I have a Cisco 800 series router that I need to set NAT up on. There will be four computers connecting to the internet through it. I already have the IP address coming from my cable modem I just do not know the command to get it to translate to my internal dhcp pool I have setup. I have also been doing some research, seeing as I only have one public IP address coming from my ISP will I have to use PAT as well?

View 1 Replies View Related

Cisco Switching/Routing :: Can't Configure SPAN On 800 Series Router

May 1, 2013

I have a Cisco 881 router running 15.1(4)M4. I am trying to configure SPAN on it to mirror my outside interface (source) to one of my LAN interfaces (dest).
 
!--- WAN interface
interface FastEthernet4
description Comcast WAN$ETH-WAN$

[Code]......
 
As you can see from the above output there is a problem with the command on this interface. When I try to set Fa0 as my source it works fine:
 
rtr(config)#mon session 1 source int fastEthernet 0
rtr(config)#
 
Is this because fa4 is layer 3 and fa0 is a switchport? If so, is there another way to set fa4 as the source?

View 4 Replies View Related

Cisco Switching/Routing :: 2600 Series Router Cannot Remember PW

Mar 28, 2012

I have a 2600 Router series and I cannot remember the Password.  I have tried following web pages that state to use control Break on the boot up but its not working.can reset that pw and write erase my configuration file?Here is my boot up.  I have tried hitting control break at the very beginning over and over and then again when at the cold boot it has not worked....
 
System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)Copyright (c) 2002 by cisco Systems, Inc.C2600 platform with 131072 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x1c9468cSelf decompressing the image : ######################################################################################################################################################################################################################################################################################################################################################################################################################################################################## [OK]
Smart Init is enabledsmart init is sizing iomem  ID            MEMORY_REQ                 TYPE00036A          0X000B3B80 C2610XM Single Fast Ethernet                0X00098670

[code]....

View 4 Replies View Related

Cisco Switching/Routing :: 3900 Series Router Licensing?

Feb 6, 2013

Can the 3900 series router be ordered or upgraded to a license with advances enterprise services?  I have a few of these routers and I'm looking to get the license upgraded if possible.

View 1 Replies View Related

Cisco Switching/Routing :: Router Boots Into Router With 2500 Series

Jul 27, 2009

I m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?

View 6 Replies View Related

Cisco Switching/Routing :: Module To Add Gig Interfaces To 2800 Series Router

Aug 16, 2012

I am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.

View 8 Replies View Related

Cisco Switching/Routing :: 1900 Series Router Not Giving Out IP Addresses

Oct 15, 2012

I've got a problem with DHCP running on a cisco 1900 series router, 1921 to be precise. The Data VLAN works perfectly, i configured a ip helper address and its working. Problem tough is VLAN 20. This is the voice vlan. As u can see in the config below, this has been configured using VRRP and VRF for failover purposes. I did more of these configurations, and they all worked fine, just not with this particular router!
 
As u will notice i deleted all the not needed to know information or i X'ed it!
 
Jan-Aart
version 15.1
service timestamps debug datetime msec

[Code]......

View 3 Replies View Related

Cisco Switching/Routing :: Recover Username And Password For 870 Series Router?

Jan 20, 2009

how do i recover username and password for 870 series router

View 5 Replies View Related

Cisco Switching/Routing :: Router 800 Series Interface Cellular0 Keeps Bouncing Up / Down

Aug 6, 2012

I was able to setup my router c819 with Verizon 3G but there is one minor thing that on the console it keeps saying:
 
Aug  7 21:04:30.067: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
Aug  7 21:04:35.111: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
Aug  7 21:06:18.423: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
 
The interface Cellluar0 is connected to Verizon 3G network and I'm able to ping and get to the internet just fine. I did few research and some people said it was access list. My ACL is below but I can't find anything wrong with it.
 
!
!
interface Cellular0
ip address negotiated

[Code].....

View 4 Replies View Related

Cisco Switching/Routing :: 887 - How To Restrict Devices Connected To 800 Series Router

Jan 30, 2013

I have a Cisco 887M router which I wish to restrict the devices allowed to be connected/allocated an IP address to two, and *only* two.
 
I can't, for the life of me, find out how to allow these two devices to connect to ANY port - I can configure a MAC restriction on a single port, but I don't know how to make it so that I can allow JUST these two devices to connect to any port in the 4 port switch/VLAN (VLAN 1 is used because the mongrel who set this up was lazy). I know the MAC addresses I want to allow
 
How I can do this? I *can* restrict any given port to the two MAC addresses - but if I try to add the MAC addresses to another port, they get removed from the initial one. I need to be able to have them connect to ANY port and work, but allow NOTHING else to work.
 
For those wondering, this is to counter a user who is utilising company resources for purposes not approved - and costing us quite a bit of money in the process.

View 10 Replies View Related

Cisco WAN :: Setup 3G For Router 819 Series

Jul 2, 2012

I have a router 819 with 3G built-in. Are there any manual for how to setup the interface celluar 0 for this router out there? I have Verizon as my 3G provider.

View 4 Replies View Related

Cisco Switching/Routing :: 1941 Series Router Stopped Responding After Restart

Aug 12, 2012

I am setting up a Cisco 1941 series router for our department in Denmark. As we quickly relised we had to reset the router to it's defult settings. As we comunicated with the router thorugh HyperTerminal, the router asked me to restart. After we did so the router only sends encrypted messages wich is unreadable. We neither get any respons in the terminal when we try to write commands back to the router.We have tried to use different terminal programs as well as the USB port on the router.

View 4 Replies View Related

Cisco Switching/Routing :: Copy Startup Configuration From 877W To Another 870 Series Router?

Jan 4, 2012

I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?

View 4 Replies View Related

Cisco Switching/Routing :: Get Fiber Optic Modules For 2821 Series Router

Mar 20, 2012

How to get fiber optic modules for Cisco 2821 series router. I can not find anything apart a SFP module which contains only one SFP port.

View 9 Replies View Related

Cisco Switching/Routing :: 1900 Series Router Needs Reboot Every Time Connection Is Lost

Jan 1, 2013

i have a cisco 1900 series router from the isp and we connect it the our router the rv042 small biz, and we have here a cisco catalyst 2950 switch with just default configuration connected to the hosts.
 
my problem is from time to time that the connection is lost there is no connection with the router and the only solution is to turn off and on the cisco 1900 router and the connection will be back.
 
do we need to configure the routers and switches? what do you need to configure?

View 2 Replies View Related

Cisco Switching/Routing :: 2800 Series Router - Multicasting Windows Deployment Services

Mar 25, 2012

We have recently implemented Windows Deployment Services on our local network, but everytime we do a multicast image deployment the network get flooded to point of total saturation.
 
We have Netgear switches and a Cisco 2800 series router. IGMP Snooping has been enabled on all Switches, however, we are unsure on how to implement multicasting on the router.
 
The whole network is flat - no VLANs over than the default VLAN1. We only want multicasting to work within our local network and does not need to go out the other side of the router as that is the connection to the internet.

How to get the Cisco router configured properly to enable multicasting to not flood the network. It seems that even if we were to image 4 PCs using multicast this is enough to completely get the network flooded.
 
Also, am I right in thinking that IGMP needs to be enabled on all of the Switches?

View 5 Replies View Related

Cisco Switching/Routing :: 2800 Series Router - Removing And Installing Compact Flash Memory Cards

Nov 15, 2011

I just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??

View 2 Replies View Related

Cisco Switching/Routing :: 891 Router NAT Setup

Nov 15, 2011

I've got working PAT, but absolutely not sure how to perform additional task.

ip cef   
no ip bootp server
no ipv6 cef
interface FastEthernet8
ip address 192.168.1.141 255.255.255.0
duplex auto
speed auto
[Code] ........

View 22 Replies View Related

Cisco WAN :: How To Config Other 7 IP Address On Web Server In Router 2800 Series

Jan 10, 2011

i have Router 2800 series we are using  leased line Connection 8 Pubilc IP.One IP Config in Router FE0/0 IP  101.102.148.91 and FE0/1 192.168.0.0 Local IP.I have 6 Web Server. How to Config other 7 IP address on Web server in the router 2800 series.

View 6 Replies View Related

Cisco Switching/Routing :: How To Setup 2600 Router For SDM

Jul 8, 2012

I have a 2600 router and im trying to set it up for SDM. The crypto command is not there. What do i do?

show version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(15b), RELEASE SOFTWARE (fc1   )
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 25-Aug-05 13:38 by ssearch
Image text-base: 0x80008098, data-base: 0x81A255C4

[code]....

View 3 Replies View Related

Cisco Switching/Routing :: IP Routing On 6500 Series Versus 3750?

Jan 24, 2013

For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?

View 1 Replies View Related

Cisco Switching/Routing :: L3 Routing With Catalyst 4900 Series?

Mar 19, 2013

I have peculiar challenge ahead of me and would like to get new perspectives.
 
The objective is to route specific VLAN traffic and the caveat is that I have multiple VLANs with the same network address.
 
For example:
 
VLAN100 10.10.10.0/28 VLAN101 10.10.11.0/28 VLAN102 10.10.12.0/28
VLAN103 10.10.12.0/28
VLAN104 10.10.11.0/28
 
I need traffic going from VLAN100 with a destination of 10.10.11.0 forwarded to VLAN101 and NOT VLAN104.
 
This task is currently being completed by a multi context firewall and we're trying to decommission the asset.

View 5 Replies View Related

Cisco Switching/Routing :: IP Routing On 6500 Series Vs 3750?

Oct 30, 2011

For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?

View 2 Replies View Related

Cisco Switching/Routing :: To Setup NVI On 1941 Router - Configuration

Dec 9, 2012

Here is my current config, how to enable and setup NVI on a cisco 1941 router.i think it would fix my issue but i'm unclear on how to implement it to test.
 
i would like to be able to access an internal server from an outside address.

View 4 Replies View Related

Cisco Switching/Routing :: Setup VLAN Between 3845 Router

Jan 30, 2012

I have a Cisco 3845 Integrated Service Router and I have installed a Service Module. I want to use the integrated Gigabit ports as switch ports and put ports in the Service Module and Gigabit port in a VLAN.
 
Is this possible? can it be done by setting internal Gigabit link as trunk and how? Below is the somewhat the setup i am looking for
 
Service module
fa0/1 |
fa0/2 | Vlan X
fa0/3 |                       
[Code]....

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved