i have Router 2800 series we are using leased line Connection 8 Pubilc IP.One IP Config in Router FE0/0 IP 101.102.148.91 and FE0/1 192.168.0.0 Local IP.I have 6 Web Server. How to Config other 7 IP address on Web server in the router 2800 series.
View 6 RepliesI have a 2801 running c2801-spservicesk9-mz.124-3g.bin According to the Cisco IOS MIB locator the image supports OLD-CISCO-SYSTEM-MIB I have tried .1.3.6.1.4.1.9.2.1.55 etc to set server IP address and the filename string but without any luck.e.g.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.2.1.55.a.b.c.d (where a.b.c.d is the server IP)
I have also tried the method similar to that for Cat 3550 switches where you create a table of entries to define the transfer paramaters then activate the transfer (I think the CISCO-CONFIG-COPY-MIB)
e.g.
[URL]
C:>snmpset -v 1 -c private <device name> ccCopyProtocol.<random number> integer 1 ! 1 = tftpccCopySourceFileType.<Random number> integer 1 ! 1 = networkFileccCopyDestFileType.<Random number> integer 3 ! 3 = startup & 4 = runningccCopyServerAddress.<Random number> ipaddress "<server ip address>"ccCopyFileName. <Random number> octetstring "<file name>"ccCopyEntryRowStatus.<Random number> integer 4 ! 4 = createAndGo, or 1 = Active
To write net have the source as running (4) and the dest as network (1)
ccCopySourceFileType.<Random number> integer 4
ccCopyDestFileType.<Random number> integer 1
Clean up at the end - destroy .14 with the value of 6.
example output : -
-- earlier output omitted --
Error in packet.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.4.111
Error in packet.
[code]...
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedHow many IP address can handle the DHCP server of the RV0xx Series VPN router? can be configured for more than 250 ip addresses? it is posible to configure the router in order to have more than 250 ip address?
View 2 Replies View RelatedThe public IP address of my 2800 router where all VPN clients terminate will change shortly. There are some technique to auto-change the client´s profile for clients to connect to the new IP address? I have seen that VPN 3000 concentrator is able to do this so i can´t get one of those right now
View 1 Replies View Relatedi have one cisco router 2811 now its not booting normally.
Router was working without any problems but due to power loss router restarted and goes into rommon mode
I tried to boot from flash and usbfalsh with different images but no use router is in still rommon mode.
here the output of my router:
program load complete, entry point: 0x8000f000, size: 0x3117470
Error : compressed image checksum is incorrect 0x8E095E7F
Expected a checksum of 0x8E0AE77F
*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x80014e20
[Code].....
I have Router 2800 series Global nating is configured on it.
ip nat inside source list 111 interface Dialer1 overload
!
access-list 111 deny ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
My object is that i want give internet access only for few users ip E.g IPs addresses from range 192.168.1.0-10 can acess intenet access other all are deny.How i do this with ACL .
Any problem/issue with using 28VDC to power the 2811 router. The spec calls for a 24VDC power.
View 1 Replies View RelatedI have a comcast business class cable modem and am trying to connect it to my cisco 2821 to route only certain types of traffic.
View 3 Replies View RelatedHad no problem getting into IOS via Terminal and changing the host name, username and password. Then I loaded the Cisco CP Express onto a system and got into the web config. Problem is....the default IP is 10.10.10.1 / 255.255.255.248 and I wanted to change it to 192.168.1.1 / 255.255.255.0 I did it in the web interface and it applied to the router, but after that I could never bring up the web interface again on 192.168.1.1. Checking IOS showed that the new 192.168.1.1 did indeed "take". I even added an access list for the 192.168.1.0 network.
View 8 Replies View RelatedI am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.
View 8 Replies View RelatedWe have recently implemented Windows Deployment Services on our local network, but everytime we do a multicast image deployment the network get flooded to point of total saturation.
We have Netgear switches and a Cisco 2800 series router. IGMP Snooping has been enabled on all Switches, however, we are unsure on how to implement multicasting on the router.
The whole network is flat - no VLANs over than the default VLAN1. We only want multicasting to work within our local network and does not need to go out the other side of the router as that is the connection to the internet.
How to get the Cisco router configured properly to enable multicasting to not flood the network. It seems that even if we were to image 4 PCs using multicast this is enough to completely get the network flooded.
Also, am I right in thinking that IGMP needs to be enabled on all of the Switches?
I just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??
View 2 Replies View RelatedWe've just discovered it seems the 2800 series aren't getting IOS 15.2?
We're running a 2851 for our CME and specifically want some features in CME 8.8...
End of Sale has been announced, but as it stands you can still purchase this router new today.
I have Cisco 2800 series router. When I am trying to write memory getting error message " Error opening flash:config-backup-1 (No more root directory entries available)" When there is simultaneous access to a router's NVRAM, we might encounter these errors. In order to clear the line the other user(s) is (are) connected on and free the NVRAM, issue the clear line command. But still getting the same error message.
View 1 Replies View RelatedWe have an MPLS network to a half dozen remote sites. At our main location we have a 2800 series router. In the routers config are the following lines for QOS. When I go to the routers on the other end of the MPLS, none of them are configured with these same policies. Would these not be in the running config of the 1800 series routers, or is this not setup correct and this should be removed?
View 13 Replies View RelatedEach time I enter show run on my router 2821, it takes ages to display and I have a cpu peak from the ssh process ( I am connected through SSH)
RTR-2821-01#sh proc cpu sorted
CPU utilization for five seconds: 96%/21%; one minute: 34%; five minutes: 22%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
55 26948 814 33105 74.96% 16.92% 5.87% 323 SSH Process
I'm trying to turn off SSH version 1 & 2 to pass PCI compliance. Problem is, I cannot touch the VPN link between the two offices. I'm afraid the PKI certificate used for the VPN will be deleted if i zeroize the RSA key which seems to be the only way to stop the router responding on port 22.
Here is the stuff from the running config related to the crypto map:
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
[ code].....
I'm only CCNA so I'm not even sure if the certificate or RSA key is being used for the VPN link, but I can't tell from the running config that zeroizing it would be a good idea and not break the VPN. I'm open to other ways of disabling SSH, as we are able to just connect using a console cable. But it looks like denying port 22 with an access-list doesn't even stop the router from responding to the port.
My Cisco seems to be stuck when it boots up, with the following:
Upgrade ROMMON initalized
And it goes on with self comperessing image then an OK but then it starts loading again all over.
Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers
View 8 Replies View RelatedIs there a way to set static routes per VLAN?Example VLAN 100 sends all traffic to 192.168.1.1 and VLAN 200 sends all traffic to 10.1.1.1. (2800 Series RTR)I have 5 networks that have their own gateway to the Internet via satellite link. Those networks run over the same infrastructure on separate VLANs. They frequently send traffic to each other, which gets sent over a slow SAT link. I introduced a router to the network and would like to set all my hosts default gateway to the local routers sub-interface then have a static route that send all traffic that is not on one of my 5 networks back to that VLANs respective SAT modem to get routed out over the Internet.
View 4 Replies View RelatedIn a site we currently have 1 BT provided ADSL link which is currently terminated using their device which I believe is some kind of 2wire device, which is extremely slow due to distance from the Exchange (4Mbps)...We have a growing number of users here and want to install a second ADSL line from BT to give them increased performance.
We have a Cisco 2800 sat not doing much so I was wondering if I could use this to load balance the link? I know BT do not support MPPP so therefore the maximum any user can get will be the speed of a single link (4Mbps)...But basically how can this be done..
Can I leave the two BT routers in place and place the Cisco 2800 behind them, or do I need to purchase two ADSL modules for the 2800 and terminate the connection there?Also once done, what do I need to do regarding actually setting up the load balancing? I have seen this:
[URL]
But am unsure as to how relevant it is? I am not sure I understand what the ACL's are being used for? I just want all users on the LAN to load balance out...
Also I am unsure of this statement:You potentially need to add policy-based routing for specific traffic to ensure that it always uses one ISP connection. Examples of traffic that require this behavior include IPSec VPN clients, VoIP handsets, and any other traffic that use only one of the ISP-connection options to prefer the same IP address, higher speed, or lower latency on the connection.I do not understand why a established session such as a VPN client, would ever traverse the second ISP connection anyway?
I'm stuck with some NAT issues. I've got an 800-series router wich connects to the internet via a PPP connection (dialer0). On the inside the router has 192.168.0.253/24 as IP address, the outside is negotiated with the ISP
My mailserver has the ip address of 192.168.0.1 but with default gateway of 192.168.0.254 (primary internet connection). If I use plain NAT (ip nat inside source static tcp 192.168.0.1 25 interface Dialer0 80) the packets arriving on the mailserver do have a public IP address as source address.
Would it be possible to rewrite those packets (source address) so they have 192.168.0.253 as source address. This way the mailserver won't send the replies to it's default gateway but back to the cisco router.
I would like to setup RDP on my cisco router so I can access my server from outside my network. I also have a router from my ISP that has DHCP for my external IP address and DHCP for my internal as well.
View 3 Replies View RelatedI have a 2821 ciso router and i want to setup a vpn for my windows domain users , they must to reach the domain from outside. There is posibile to intregrate Active directory auth with pptp running on 2821 router? kind of dialin via radius server(IAS running on windows server 2003).
View 3 Replies View RelatedI've got an old 2800 server which I'm troubleshooting some nic issues. It has Intel pro 1000 mt nic in it. There are no new dell drivers available but there are some much newer drivers on the intel site. Since this is a live server I want to check to see if any issues upgrading nic drivers downloaded from intel on a dell server.
View 1 Replies View RelatedI have a Dell PowerEdge 2800 (Just reinstalled windows Server 2003) I have tried the two (non lan) network driver setups that dell has on its site and I get "the update package is not compatible with your system configuration".
I am trying to access the internet on my box, how to accomplish this or fix the problem I'm getting while loading driver setup?
I have a Cisco 831 router (c831-k9o3y6-mz.124-5c.bin) that cannot backup the config to a local tftp server. I have seen this behavior on a few different Cisco devices over the years and have never found a solution. The connection is made to the tftp server (in this case tftpd but similar behavior on any tftp server) and a blank file is created on the target machine file system, but the data is never transferred.
The router shows %Error opening tftp://192.168.0.2/router-confg (Timed out) [Failed]
The tftpd log shows 5 repeated attempts at the file write.
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:40.922]
Write request for file <router-confg>. Mode octet [25/05 11:56:40.922]
Using local port 61607 [25/05 11:56:40.922]
<router-confg>: rcvd 0 blk, 0 bytes in 3 s. 0 blk resent [25/05 11:56:43.922]
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:43.923]
[Code]...
This is also stopping me upgrading the image on the router as I cannot transfer in the other direction either.
I seem to be having a problem with DNS name resolution after configuring my router (Cisco 3725 running IOS image: c3725-adventerprisek9-mz.124-25.bin) for handling DHCP requests.
Before I made the change, everything was working correctly; I could ping Google.com from a computer inside my LAN and would get response from one of Google's public IP's like normal.
I had a separate DHCP/DNS server running Windows Server 2008 handling the DHCP request and DNS queries.
When I made the change, I turned off the DHCP/DNS server and issued the following DHCP commands to my router:
Code...
It's been a while since I've done a lot with a PIX config so what is the best way to allow access for 2 IP addresses that need to RDP into a server here inside our network. They also wanted to have ports redirected, 3391 to 3389 and 3397 to 3389.
View 12 Replies View RelatedSome Routers support DHCP spoofing (zyxel / speedtouch).With DHCP spoofing (or half bridge) you can directly spoof you'r public IP address to the firewall. Firewall gets public IP address directly from modem. Benefit of this (no waste of an extra IP address). Modem has no IP address. It has to be possible with an 8xx series router I heard, but I cannot find how.I guess it can be done with a bridgegroup with the dialer and VLAN 1 in it (no ip addresses given).I tried but without any result.
View 2 Replies View Relatedhow can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies View RelatedI have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View Related