How many IP address can handle the DHCP server of the RV0xx Series VPN router? can be configured for more than 250 ip addresses? it is posible to configure the router in order to have more than 250 ip address?
View 2 RepliesI have a RVS4000 router with DHCP enabled and in router mode.
The LAN is 192.168.2.x. The RVS4000 static IP address is 192.168.2.8
The router is not the RVS4000 and is at 192.168.2.1
The RVS4000 dhcp is assigning it's clients a default gateway of 192.168.2.8 instead of what I want 192.168.2.1. How can I get the RVS4000's DHCP server to assign another IP address other than its own as the default gateway to its DHCP clients?
I was trying to set a DHCP pool with 127.16.0.0/16 with RV220W, however, RV220W UI can't save it. It displays "IP Address Range -"Step to reproduce: (it is 100% reproducible)
1. login into RV220W admin web
2. Create a VLAN, id 201
3. Go to "Multiple VLAN subnets", select the VLAN, click edit
4. Enter following info:
IP Address: 172.16.0.1
Subnet Mask: 255.255.0.0
DHCP Mode: DHCP Server
Domain Name: Cisco
Starting IP Address: 172.16.2.100
Ending IP Address: 172.16.10.254
Primary DNS Server: 172.16.0.1
Leave rest of settings with default value.
DNS proxy is enabled
5. Press Save button. The UI shows text "IP Address Range -".
Expected result: RV220W shall save the setting and make use of 172.16.0.0 subnet in IP pool. By the way, the error message "IP Address Range -" seems incompleteI tried same setting on netgear FVS318N (very similar settings to RV220W), it accepts 172.16.0.0/16 as DHCP IP pool and works.RV220W has great feature set meets my needs. Its UI is slow and sometime dashboard freezes, which I can live with comparing to features. But DHCP server IP pool can't be class B is huge limitation to me.
I want to pass my client VPN request to MS Win Server 2003 - on FW I forwarded port for PPTP service to my server address, but on client side I get an error 619. On Cisco RV120W I have Site-to-Site VPN tunnel which works fine, PPTP server on Cisco is disabled. What should I do to pass VPN request to my LAN server to handle it?
View 4 Replies View Relatedi have Router 2800 series we are using leased line Connection 8 Pubilc IP.One IP Config in Router FE0/0 IP 101.102.148.91 and FE0/1 192.168.0.0 Local IP.I have 6 Web Server. How to Config other 7 IP address on Web server in the router 2800 series.
View 6 Replies View Relatedwe have some RV042 Routers with Firmware 1.3.12.x we would like to replace with the new V3 hardware.
We downloaded the migration utility 1.0.2.2, which crashes for at least one device.
The release notes for the utility are for version 1.0.2.8, where some crashes seems to be fixed, but where can we download this actual version?? I can only see the (older) 1.0.2.2..
I have a 3911 router with a 1242 AP. The problem that I have is that when the user is trying to connect, the user get the OS Ip address 169.254.168.154 and I see that when I do the "show dot11 association" command, but when I do sh ip dhcp binding on the router I see
172.19.9.141 0100.18de.74db.14 Jan 31 2011 11:14 AM Automatic
The router is seeing as if the router gave the ip address to the user, but the reality the user was assigne the OS ip address 169. I did "debug ip dhcp server events" and I got the following:
Jan 31 11:09:06.752 EST: DHCPD: Seeing if there is an internally specified pool class:Jan 31 11:09:06.756 EST: DHCPD: htype 1 chaddr 0100.18de.74db.14
Jan 31 11:09:06.756 EST: DHCPD: remote id 020a00000a58218400000000Jan 31
[Code].....
i did just had a rogue anti-virus infection i did a removal of it AV Security 2012
View 1 Replies View RelatedNormaly all incoming IP addresses can use NAT to gain access. I would like to make a rule that only one IP address can connect to my router and use that port or range of ports defined.
Is there a way to configure a SRP 527W on such a way?
If not possible now, can I expect a software update ?
How come the 2600 series IOS has the show mac-address command but it does not display anything? you need to use show arp? is this for when you use one of those network modules that is a switch?
View 2 Replies View RelatedIs it problem with iPads or LAP1141n?WLC 4404 and many 1142 and 1141, so other devices laptops, iphones, androind phone works as well.But iPad authorized, but can't get an ip address from dhcp server (dhcp not local on wlc, on windows machine) with coverage lap1141, but it get ip with coverage lap1142, and when i got it i roaming to lap1141 and it stays, if i off/on iPads can't get it again from lap1141.
View 14 Replies View Relatedmy Laptop is about nine years old, HP Pavillion Pentium 4. I run Windows XP Home Edition Version 2002 SP3. I use a broadband card from Verizon that I just put in my USB (no router, etc) I'm getting a System Error Source DHCP Event ID 1002. When this happens, my computer, I believe, is going into sleep mode and I have to reboot the system. When I turn it back on and go back on the internet, all my websites that I was in are still there. The error says: The IP address lease 10.170.223.48 for the Network Card with Network address 2c3068c16ED1 has been denied by the DHCP Server 10.173.229.86 (The DHCP Server sent a DHCPNACK message)The DHCP Server Service did not extend the lease on your computer's IP address, so your computer temporarily lost its connection with the Network. I tried the ipconfig /release and ipconfig /renew. I tried going in services.msc and going under DHCP and keeping it automatic but stopping it. I called Verizon and I believe he refreshed my Network settings (I think I knew more about the topic than he did) He said it was my computer, whatever. I just tried the static IP but it didn't seem to take. I restarted and it jumped back to automatic. My last guess is it's something to do with the time frame of when it automatically obtains the address and when it expires. When I do the ipconfig /all it shows only a two hour time frame before it expires. Today I noticed that my computer shut down/sleepmode at the exact time the ipaddress was obtained. So, is there a way to increase this time between obtaining and expiring?
View 7 Replies View RelatedI'm a heavy PC Gamer, I play games such as World of Warcraft, Borderlands, Call of Duty, Steam Games, I also know my way around fixing internet issues, But this one just seems to have gotten me off guard, Recently, 1-2 days ago, I was browsing the internet like a normal day, and It was late, so I decided to go to sleep, Turned my computer off, Woke up the next morning, Turned it on, It then shows that I kept getting kicked off the LAN for some reason, It was like this[CODE]
View 2 Replies View RelatedI have a 1250 AP connected to an Switch Cisco 3750. We have a SSID(v lan 1 - native) which get an IP Address from our DHCP Server(located in a Windows 2003 server). I added a new SSID in VLAN 2 and I would like no to use the DHCP Server but to make the AP get an IP Address from the pool I created in the own AP (ip dhcp pool Guest) but every time I try to connect the new v lan, it doesn't get an ip address.
Follow the settings of the AP.
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[Code]...
My 5508 WLC which runs version 7.4 is configured as a DHCP server for the AP management and here's my problem: My AP can get to the address, and can ping the address of the WLC management，But my AP prompts the following log： [code]
In the switch dhcp we can use to do the WLC option43 specified address, but in this case how the address specified WLC, the AP can be registered up?
My Network is running Windows Server 2003 and with more than 150 Users. But last week, I notice that a program is changing my DHCP server IP Address scope.
View 2 Replies View RelatedI randomly lost Internet connection, and since have not been able to Renew an IP address! Other people in my household can connect just fine. I've tried numerous things to get my internet back, but continue to be unsuccessful in doing so.
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsMike>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : miker
Primary Dns Suffix . . . . . . . :
[code]....
2 brand new Vostro 270s straight out of the box both have the same problem. (Windows 7 PRO)
These are connected to a wired LAN, the NIC fails to find the dhcp server and get itself an ip address. The network cable & port work fine with any other PC. If I change the properties in the NIC to a static IP address it works fine.
I have tried every Realtek driver I can find, both from DELL and Realtek, no difference.
I have wiped one of the machines and re-installed a fresh copy of Win 7, then the chipset drivers (from the DELL supplied CD) - no difference.
It took a while of troubleshooting since I've never ran into this problem with my wireless router before. But finally I figured out that my router will not assign the proper DNS server addresses when assigning through DHCP. I upgraded from 2.10.02 and still the same issue.
View 1 Replies View RelatedI have 2 units Cisco WLC 5508 running software version 7.0.220 with 70 over units Cisco AP 1262N and 1242AG. Some of wireless clients having problem to get the correct IP address from the DHCP server. There are 2 units of Microsoft DHCP. Both DHCP server ip have been configured on the Interface at the WLC. The core switch also being configured with ip helper. I've attached the debug output of one of the wireless client during the problem.
View 12 Replies View Relateda new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?
portfast an dother parameters are intact.
We have 2 nexus 7010 switches configured with HSRP in the network. For all the vlans core1 is Master and Core2 is standby. In the current setup we have external dhcp server and dhcp relay is configured for all the vlans on Master and standby switch. The setup is running the IOS 5.2
Activity Done: During the Maintainacne activity, we isolated core1 switch in the network by disabling the vpc/keepalive and all the uplinks from access switch. The core2 switch was master for all the vlans.
Issue observed: It has been observed that new users were not getting ip address from the dhcp server. The ethereal capture showed that dhcp server was not getting the dhcp requests from the core2 switch. We disabled the dhcp feature in core2 and enabled again with dhcp relay again configured on vlan interfaces .even after doing this no change was observed in behaviour. Finally we got core1 back in network by enabling all the links.
Observation: The moment VPC link came up between the core switches, users started getting ip's from dhcp. Then we started enabling all the uplinks on core1.Core1 again become master for all the vlans and users continued getting ip’s. Network running fine.
Further Testing
1. For one of the vlan, core 2 switch has been made primary and for new users checked the dhcp functionality and it was working fine. The aim was to identify if anything wrong on core 2 related to dhcp relay
2.Again we changed the priority for this vlan and made core1 master for the same. This time we disabled this vlan on core1 and tried new user with core 2 became master and dhcp functionality worked fine for new user. Actually in this case we have simulated the same behaviour when we observed the issue with only difference of VPC was not available during the issue time as core 1 was isolated form network
Inputs needed.
Is there any known behaviour for dhcp functionality when VPC is unavailable? If we see the test scenario2 (wherein core1 was master for the vlan and we disable this vlan on core 1 and core 2 was able to relay dhcp requests for new users in this vlan.) it was actually same as scenario we observed during issue time..
I just tried replacing a cheap domestic router/switch with an RVS4000 V2 on our work network. This has a WAN connection to a cable modem for internet access via a dynamic IP address.
When I first connected the RVS4000 it got a WAN ip address via DHCP of 192.168.100.11. This is the type of IP address we get when there is an upstream problem with our ISPs cable network, and sure enough we had no internet access. The RVS4000 was set to use DHCP on the WAN interface. So I logged a support call with our ISP but they said there were no problems at their end.
I then swapped the RVS4000 out for the original router. This worked fine and got a WAN DHCP address of 77.xxx.yyy.zzz as it should. Swapped back to the RVS4000 and back to the same problem of getting a 192.168... address.
So, I downloaded the latest firmware from Cisco, which was V2.0.3.2 and flashed the RVS4000.
I then tried again connecting the RVS4000 to the cable modem but this time it would not get any WAN DHCP address at all. On the Status/Gateway page of the web interface it said that the WAN interface was down. However, on the front panel there was a yellow light indicating a live connection on the internet port.
How do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies View RelatedCan a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies View RelatedDoes the 2960 switches with LAN-Lite support DHCP Server Port-Based Address Allocation?
View 1 Replies View Related2 days ago, my laptop was connected to my router and working fine. But it then randomly disconnected and haven't been able to connect back since. I am using an ethernet cable to access the internet, and have tried many ways to try and resolve the issue but nothing is working.
I have a Dell L501x (Win 7 64-bit) with the Intel Centrino 1000 BGN wifi card. I have restarted the router and modem and disconnected all devices and tried reconnecting, but to no avail. I have tried updating the drivers, system restoring and using safe mode (with network) but nothing works. The modem and router are working fine as other devices connect and access the internet, it is just my laptop that cannot.
I am sure it is not a hardware issue as the card detects all the surrounding networks. The troubleshooter only says "An administrator profile failed to obtain an IP address from the DHCP server.
I've set up a DHCP reservation on a Netgear wpn824v3 router, using its "Attached Devices" list to specify the MAC address of a computer on the network to use IP 192.168.5.200. After using "ipconfig /release" then "ipconfig /renew" on the client PC, though, the client PC keeps going back to the address it got automatically, i.e., 192.168.5.3.How can I force the client to use 192.168.5.200?
View 1 Replies View RelatedI've purchased a router SRP547W and I would disable DHCP server. On the control panel I can't see anything about disabling this function. I don't need dhcp server on router and I don't need dhcp relay. My firmware version is 1.2.4_003.
View 4 Replies View RelatedSo far we add any router in the existing network simply by disabling DHCP server, and adding LAN ip for that. We don't add WAN detail at all in the additional routers. And plug one cable from main network to the LAN port of the additional routers.So we basically use that additional routers only as a access point for WIFI.But what I wonder is if it's possible for me to use the additional routers with the same feature as of the main routers i.e. Enabling DHCP server so that it too can give its own DHCP ip address.
View 2 Replies View RelatedThe operation steps on router (WRVS4400N):
1.Set the IP mode as Dual-stack IP and then save
2.Disable the IPV4 DHCP server
3.Use other deivces to connect the router.
The connected devices have the same IP address(2005:123:456:789::1),I am confused,why is it?
i have a cascading network in my house of 2 linksys routers, I left the DHCP server activated on both of them and it seems to work fine, whats the point of turning it off?
View 2 Replies View RelatedMy network topology is as follows:
Internet <-> Residential Gateway (RG) from ISP (OEM: Pace) [192.168.1.254/255.255.255.0] <-> RV180 [192.168.1.253/255.255.255.0] <-> SG500 switch [192.168.1.250/255.255.255.0] <-> rest of network.
I know this is a cascading LAN-to-LAN arrangement. The cable from the RG to the RV180 is from a LAN port on the RG to a LAN (not WAN) port on the RV180.
I eventually want to segment my network into a few VLANs from the RV180 down. I am aware most people would recommend DHCP on the "primary" router, but the RG is non-VLAN aware, so I figure I need to handle the DHCP off the RV180. At the same time, I have also opted not to do a LAN-to-WAN cascade because I want to retain the ability to configure the RG from the rest of the network and not have to cart a computer over to the RG to do it.
On the RG, I've disabled DHCP, and placed 192.168.1.253 in the DMZ.
On the RV180, I've enabled DHCP and put it in Router mode.
The issue is that I do not have any Internet connectivity. If I allow the computers in the network to receive IP addresses over DHCP, the default gateway that is communicated is 192.168.1.253, which is the RV180. If I configure static IPv4 information on my computers to point to 192.168.1.254, I am able to connect outside, as you would expect.
How can I get the RV180 to pass out DHCP IP addresses, but point to 192.168.1.254 as the default gateway? I thought the solution might be to create a default route (or something). I went to the static routes tab but it wouldn't let me enter 0.0.0.0 as a destination IP to route through 192.168.1.254.
Further down the line, is it possible for both the RG and the RV180 to connect directly to the SG500, along with the other nodes in my network? That way the RV180 only serves to maintain the VLANs and pass out IP addresses via DHCP, instead of having it be the choke through which everything goes through on the way out?