I want to pass my client VPN request to MS Win Server 2003 - on FW I forwarded port for PPTP service to my server address, but on client side I get an error 619. On Cisco RV120W I have Site-to-Site VPN tunnel which works fine, PPTP server on Cisco is disabled. What should I do to pass VPN request to my LAN server to handle it?
View 4 RepliesHow many IP address can handle the DHCP server of the RV0xx Series VPN router? can be configured for more than 250 ip addresses? it is posible to configure the router in order to have more than 250 ip address?
View 2 Replies View RelatedThis is only a small portion of our network but my question is, can these 1841 routers handle a 45Meg connection? I thought these routers were designed for T1/E1 type speeds. I know I saw a router performance document somewhere that showed 1841's could handle 38.4MB of traffic and that is only with routing turned on. If anything else is enabled, like access lists, NetFlow or whatever, that number will decrease because of the capacity of the router. Am I correct in these statements? Any document or anything else that shows performance of these routers?
View 14 Replies View Relatedhow do I pass from domain server , my network in our compant have ISA server and they close some website like face book , how can I pass over ISA server and use my websites?
View 3 Replies View RelatedAccording to traces collected in mt ACS SE 4.2, it would seem that the underlying software does not support the RADIUS Status-Server request. Is this request type is supported in version 5.*?
View 2 Replies View RelatedFor the moment we run a Nortel VPN server at work and I have on my laptop the Nortel VPN client. While I could connect through when I had my Linksys E2000 connected up now I can't after I replaced it with the 5505. (running 8.4(1).) what I should do on my 5505 so I can allow the nortel client to connect out?
View 6 Replies View Relatedis this network able to handle wifi 200 clients?Load balancing QNO FQR7110[URL]Access point: TP-LINK 300Mbps Wireless N Range Extender (TL-WA830RE)[URL].My client is all students... and all of them will connect to the internet by using Wireless connection.So i estimate 12APs for them.. each access point will have around 17 clients...and the 6 APs will be connect to 1 HP 1910 Switch Series 8 ports switch...*Note: the switch is Smart managed switch, but im not going to setup it.. i will just plug and play..May i know it is suitable to use that model of device to setup the network with 200 clients?The load balancer and switch it is enough Processor and RAM?
View 2 Replies View RelatedI have a Cisco wag120n adsl modem. I am setup with a SIP provider, so all my incoming and outgoing calls use SIP.So my question is, how does my ADSL modem handle incoming SIP calls,e.g the SIP call comes in and reaches my adsl modem. Then, how does the modem find the actual port that has my ATA adaptor (analog phone) or CME router attached ? I know port forwarding would handle this, but I am not actually using any configured port forwarding rules.
View 1 Replies View RelatedWe are experiencing a lot of these RADIUS failed to respond messages on our WLC's leading to a lot of RADIUS server hopping within the WLC.We are using Cisco 5508's, 1142 AP's and a Microsoft NPS RADIUS backend. SSID is WPA2+802.1xThe first workaround to this problem was to disable aggressive failover on the WLC. But this is only a temporary fix, because in the end, there will be more than 3 consequetive clients, failing to authenticate to the WLAN network. As a result, the WLC will swap to the 2nd RADIUS server configured.When we dived into this a little bit more we saw the following messages being logged on the RADIUS backend at the time we saw the RADIUS messages on the WL:Event ID: 6274: Network Policy Server discarded the request for a user.
View 16 Replies View RelatedI have reinstalled windows 7 on my Toshiba laptop, I have my wireless set to automatically connect, I have excellent signal strength and have another pc connected to wireless router, but my laptop does not capture IP addresses. I tried renew command but got message unabl to contact your DHCP server, request timmed out.
View 1 Replies View RelatedWe have a Cisco ASA 5520
We are attempting to setup RRAS on Windows 2008R2 using L2TP. Server is on the inside of the network at 10.10.10.20 our ASA is 10.10.10.1 its outside interface is 68.0.0.0.3/28.
I set a static NAT rule to allow all traffic pointed at 68.0.0.4 to be directed to 10.10.10.20 and have ACLs allowing the following.
esp, ah, udp/500, udp/4500, udp/1701
Mac Clients have no issues with but windows clients seem to hang and never connect. I know the ASA configuration is somehow to blame, if I attempt to connect to LAN IP (10.10.10.20) from withn the same network every thing works fine (making sure all the Windows Issues are covered).We have 2 other IPSEC tunnels established to teh ASA from our COLO and a Satalite office, not sure if this makes it any harder.
I'm having some trouble with my P660RU-T1 configuration. I have recently set up a linux SFTP server at my home and am trying to access it via my public ip (eg 1.1.1.1), the problem is this public IP goes to the router which doesnt pass on the requests to the server.Last summer when i first messed around with this i had no problems with using the public ip to access the server, its only recently.
View 1 Replies View RelatedI've been having problems connecting my laptop to the internet through wireless. When I plug it in with a cable it works fine. I also know my wireless works fine because i have other things attached to it. When I try to connect it says limited or no connectivity, but the signal strength is excellent. I have tried to repair the problem but it then tells me it cannot renew my ip address. I've also tried the ipconfig /release then renew, and thats when it says about my DHCP.
View 1 Replies View RelatedI would like to set up a site to site VNP connection between 2 RV120W routers, preferably via IPsec.
The problem is that I would like/have to use a 4G modem router (model TINY) which connects to internet in front of the RV120W (on the local side)
I have no problem with that on the remote site that RV120 connects directly to internet via a public IP address on the WAN port.
Local network 192.168.1/24-----RV120W----192.168.100.1—Tiny---Public IP--------INTERNET
INTERNET--------PublicIP—RV120W—Remote local network 192.168.2/24
I've a RV120W with the last firmware version (june 2011), i want to create two vpn tunnel:
- Professional: lan routing all packet for the 192.168.0.0/24 to the first VPN tunnel
- Other: all other address IP destination to a second VPN tunnel
The first tunnel (professional) is ok but what rules can i use to configure the second ?
What is the default login/pass of cisco rv120w for ssh access ?
View 1 Replies View RelatedUpgraded to 1.0.2.6 and all of a sudden SIP devices working over the VPN no longer work. Downgrade to 1.0.1.3 and they work again. My guess is that some ports are blocked over the VPN in 1.0.2.6
I thought the general idea was that firmware ugrades fixed bugs rather than introducing them.
Suggestion for Cisco:- Zip the firmware image downloads, or else have an upgrade process that includes a CRC check, that way at least the poor punter will have an indication if they have been corrupted. I had a subtle memory problem that was corrupting some files. The firmware upload appeared to complete properly and you could log on OK but some of the menu choices resulted in a hang with the "Please wait... the page is being loaded" message. Careful checking of file sizes revealed that the file I was uploading into the router was a few hundred bytes different in size to the one on the website, must have been corrupted during the download. But the upload proceeded normally with no indication of any error. It's a pretty basic safeguard that should be in there as a matter of course with the router performing a CRC check and showing an error if it fails.
I had WRT54G2 and recently switched to an RV120W. I have an Internet accessible camera system connected to my router. Before, this worked fine... there is a dns service (DynDNS.com) that is configured as part of the camera setup. I would then just enter [URL] and I would connect to the cameras. I install the new router (RV120W) and I can no longer connect to the cameras. I do not recall any configuring that I had to perform on the old router.
why the RV120W isn't letting me get to the cameras?
Rx:, recently I have perchase 2 RV120W routers thinking that it must be very easy to setup the site to site vpn. i cannot get my remore office to link to my main office and vice verser.
Scenaro
- I'm using 2 RV120W routers for each site.
- Site A using a subnet of 192.168.10.0 mask 255.255.255.0
- Site B using a subnet of 192.168.11.0 mask 255.255.255.0
I have setup the VPN using the wizard and I got site to site tunnels connected and show as 1/1 Connected (1 user) in the status he IPsec connection status show
--Policy Name: VPNA
--Endpoint : public IP address from my ISP 203.117.222.221
--Packets Tx:145 Rx:0 and Kbytes shows Tx: 29.55 Rx:0
Q1 why I cannot use dynamic DNS naming in the policy setting ? eg: aaa.dyndns.org, I have to use the ip address instead eg: 203.117.222.221
Q2. I cannot connect from Site A to Site B , I can't even do a ping to 192.168.11.1 from Site A. even though it show the Site to site tunnel is coonected.
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
It works great, tunnel is UP.
[Code]....
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
[Code]....
Now, I need to be able to reach the server (192.168.1.100) from a PC on LAN #2 with IP 192.168.2.50. So, I've created au static route on Office Router #2 (192.168.2.1) because of course it doesn't know how to reach private subnet 192.168.1.x. My static route looks like this :
192.168.1.0 / 24 (Destination network) --- 192.168.2.254 (Gateway)
...but it doesn't work, no ping. When I do a tracert to server IP (192.168.1.100) from PC on LAN #2 (192.168.2.50), the result is :
1st jump ---> 192.168.2.1
2nd jump --> 192.168.2.254
...and it doesn't go further.
Recently i had suffering with wireless connection problem, currently my wireless router connected to WAN directly, after that go into firewall and then go thru switch to end user PC, for LAN user there is no issue, but for wireless connected PC it is prompted with limited connectivity problem(DHCP is disable on router), after check with ipconfig /all. it seem likely due to wireless PC cannot get the IP from DHCP server. i am using DLink615 router. i had checked firewall setting there is firewall policy that connected all router ip into company LAN, but i don't think there is DHCP VPN setting up. is there anyway i can go thru firewall and get IP from DHCP server because if i set up DHCP on router, it cannot pass thru and access to LAN.
View 9 Replies View RelatedI configured my RV120W (Firmware:1.0.2.6) to count the traffic on my network. I set the monthly limit to 99999 and did not change anything else.So after a few hours, the traffic counter shows 2048 MB for outgoing traffic. This is impossible, because the DSL-connection is too limited in upload to cause this huge outgoing traffic in 6-8 hours. When I reset the counter at night, the next morning the device shows 2048MB again (even if there was no traffic at all, just some clients syncing time with NTP). I did already reset the device to factory defaults and reconfigured everything from scratch.
View 0 Replies View RelatedI have a problem with firewall rules. If I set some rules for open communication and some for closed, so I cannot reorder from the end to begin.
Last rules are at the end of all. So I can only reorder in one pages.(I have about 33 rules = 3 pages of rules)
I was wondering if I could setup my router CIsco RV120W to be able to connect to a VPN serice for my internet connection. Looking to give my small home netwok more sercurity. Is it possible with the Cisco firmware to be able to setup a connection to VPN serice. Do I have the compabilites with this router?
View 1 Replies View RelatedThe PPTP client from Windows 7 is not working with this router; therefore I would like to try the quickvpn.Is there any paper from Cisco explaining how to setup the RV120W for quickvpn ?
View 1 Replies View RelatedI need to configure a rv120w in order to make it work at the same time for data and digital tv. The fact is that the set top box for the idtv needs an IP address that will be delivered directly from the ISP. So I need to setup one LAN port that will be bridged to the WLAN connection (the stb will be connected to that lan port), and another port that will be connected to the LAN swicth so that the rest of the network has internet access. I can't see anywhere a way to create such a bridge. Quite disappointing as it's possible to do so on open source platforms such as openWRT..
View 3 Replies View RelatedI am getting the message '400 bad request' whenever I try to backup the configuration or export a certificate under Certificate Management.
View 1 Replies View RelatedWhen I try to export an SSL Certificate for a Client I get a htps . CSR file instead of the .PEM file. So, I can't update the client computer with the correct certificate.
Firmware: 1.0.2.6
I have just received an RV120W. Default setup (out of box), but when I http://192.168.1.1 and login, the next page comes up as : Internet Explorer cannot display the webpage ? Internet Explorer is version 9.
I have allowed both http and https at 192.168.1.1 in Internet Explorer security settings/Trusted Sites ?
Is there a console connection to this box ?
Is it possible to have 2 IP addresses on wan and setup specific routing rules for each IP ? Or do I need to use another router for that and if which one ?
View 4 Replies View RelatedWhere can I download the new firmware 1.0.3.10 for RV120W?
[URL]
I have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?