Cisco Firewall :: 5520 L2TP Pass Through To Windows Server
Oct 2, 2012
We have a Cisco ASA 5520
We are attempting to setup RRAS on Windows 2008R2 using L2TP. Server is on the inside of the network at 10.10.10.20 our ASA is 10.10.10.1 its outside interface is 68.0.0.0.3/28.
I set a static NAT rule to allow all traffic pointed at 68.0.0.4 to be directed to 10.10.10.20 and have ACLs allowing the following.
esp, ah, udp/500, udp/4500, udp/1701
Mac Clients have no issues with but windows clients seem to hang and never connect. I know the ASA configuration is somehow to blame, if I attempt to connect to LAN IP (10.10.10.20) from withn the same network every thing works fine (making sure all the Windows Issues are covered).We have 2 other IPSEC tunnels established to teh ASA from our COLO and a Satalite office, not sure if this makes it any harder.
View 2 Replies
ADVERTISEMENT
Mar 25, 2011
i have configure l2tp/ipsec vpn on cisco ASA 5520 and also configure windows 7 client but its getting error
Error in ASA debug log
debug crypto isakmp 7
Mar 26 07:44:28 [IKEv1]: IP = 59.161.130.13, IKE_DECODE RECEIVED Message
[Code]......
View 2 Replies
View Related
Jun 13, 2013
Is it possible to pass 802.3 packets over a L2TP?If so, how would the tunnel differ from a normal L2TP?
View 1 Replies
View Related
Mar 20, 2013
How can I see the quantity of traffic that is passing through into an IPSec VPN in a ASA 5520.
View 3 Replies
View Related
Dec 14, 2011
we have two routers CISCO881-K9 and we have established l2tpv3 pesuduwire between two routers: attached the configuration file for both routers.
Although the l2tp established but we are unable to pass the DHCP or other traffic through l2tp tunnel from router A to router- B. [code]
View 1 Replies
View Related
Jun 20, 2011
I have installed asa 5520 , software ver is 8.4,I have SSM-20 installed in asa 5520. How to pass traffic through this ssm-20 ,how to create sensors,how to update signatures of this IPS module ,is there any procedure to automatically update the signatures .
View 1 Replies
View Related
Jun 26, 2010
I am using ASA5520 with webvpn for file sharing. But recently we just upgraded the OS that accommodate file shared folder from win2003 R2 32bit to windows server 2008 R2 64bit. Now I have a problem with accessing file share by ASA webvpn, it appears error contacting host, we have tested the file shared of webvpn on the other OS windows 2003 and windows 2008, they are working on these OS except win2008 R2. Current the ASA OS version is 8.0(2). And the windows firewall has been disabed.
View 3 Replies
View Related
Sep 22, 2011
Recently i had suffering with wireless connection problem, currently my wireless router connected to WAN directly, after that go into firewall and then go thru switch to end user PC, for LAN user there is no issue, but for wireless connected PC it is prompted with limited connectivity problem(DHCP is disable on router), after check with ipconfig /all. it seem likely due to wireless PC cannot get the IP from DHCP server. i am using DLink615 router. i had checked firewall setting there is firewall policy that connected all router ip into company LAN, but i don't think there is DHCP VPN setting up. is there anyway i can go thru firewall and get IP from DHCP server because if i set up DHCP on router, it cannot pass thru and access to LAN.
View 9 Replies
View Related
May 22, 2013
I have ASA 5520 installed. I want to use ntp server for firewall clock setting. I found one open-access ntp server (stratum 2) in Los Angeles:
[URL] 209.151.225.100
Can I use the following command to set ntp server?
ntp server 209.151.225.100 source outside.
View 3 Replies
View Related
Aug 6, 2011
Just setup a site to site vpn between 2 ASA 5520 Firewalls in two locations but vpn doesn't work even though i see phase 2 completed on the logs. I can't ping across the LANs.
View 2 Replies
View Related
Apr 17, 2012
I've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).
Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.
View 1 Replies
View Related
Apr 11, 2013
I am trying to get a L2TP/IPSEC VPN going on one of my servers behind the DIR655 router I have used Port Forwarding and Virtual Server and neithere seem to allow these ports to be open in either situation a port scan shows the ports closed..My ISP (Comcast) does not block these ports?
View 14 Replies
View Related
Dec 13, 2012
How can I access my webserver (on my private LAN) from the internet? INTERNET------------(53.X.X.1 )ASA(192.X.X.X)DMZ-----------(192.X.X.80)HTTP SERVER. I can ping my public address on the ASA outside interface 53.X.X.1 form the internet, but I'm not sure how to do this. I tried to NAT, but I'm failing.
View 3 Replies
View Related
Nov 26, 2011
I have a stable l2tp/ipsec config that I have been using for many years with the Windows XP native VPN client and the iPhone VPN client.This configuration does not seem to work with the native Windows 7 VPN client. What has changed between XP and 7 on the native VPN client front? I'm running IOS 12.4(15)T5.
View 1 Replies
View Related
Jun 28, 2012
I Have web server (linux) sits in the DMZ (asa 5520) segment and this server should be accessible form the internet,
1)how to make this server https based access over SSL
2)how to protect this server form network and security standpoint?
View 6 Replies
View Related
Mar 28, 2011
currently my firewall is Microsoft ISA Server 2006 and im using it very nicely but based on some security treats im changing my firewall from isa to ASA 5520 but im facing a problem that my i had installed on software name Soft Perfect Bandwdith Manager and i was limiting each users based on their MAC address to prevent using of full bandwidth in my internet so thats why i had a very relialble internet useage in my network.
after many search and searching i didnt find a good software or hardware that should support with Cisco ASA Apliances to support bandwidth management for endpoint users and etc and this is very troubel i dont want all users to use full badnwidth in my company becouse i have only 2MB internet badnwith taken via VSAT connection
View 3 Replies
View Related
Jul 18, 2012
I have the following setup
|| Socks Server || >> Switch1 >> ||Cisco 5520 ASA || -->> | Switch 2| -->> Clients
I have a SSH SOCKS tunnel set up on the socks server which is a Linux box. When I connect my machine to the switch 2, I am NOT able to receive and mail by setting up a mail client and it seems SOCKS traffic does not reach the socks server. I can however run a telnet command on port 1080 (socks port) which connects which shows that the port was going through and open. However there was no SOCKS traffic. When I connected the machine to Switch 1, SOCKS traffic worked as expected and I was able to receive mail.
This suggests to me that the ASA has some inherent rule that does not allow SOCKS traffic. IS this true and if so how can I bypass this?
View 4 Replies
View Related
Apr 7, 2013
I'm having problem establish l2tp/ipsec vpn connection from Windows vista/7 vpn client to cisco 1921 ( ios 15.2 )
C1 --------> (internet cloud) ---------> (cisco 1921)----->LAN
Error that I'm retrieving is always the same: Error 789: "The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer"
But I'm able to establish l2tp/ipsec vpn connection to the same vpn server with my iPhone 4.
Below is isakmp debug log from lns router(cisco 1921) when I've tried to establish vpn with windows client. Anything useful from these logs to point me on the right direction to finally solve this problem with windows clients.
#debug crypto isakmp
*Apr 8 10:56:47.018: ISAKMP (0): received packet from 186.51.43.137 dport 500 sport 987 Global (N) NEW SA
*Apr 8 10:56:47.018: ISAKMP: Created a peer struct for 186.51.43.137, peer port 987
*Apr 8 10:56:47.018: ISAKMP: New peer created peer = 0x3296C24C peer_handle = 0x80000068
[Code]...
View 4 Replies
View Related
Aug 23, 2011
I am using ASA 5520 with 8.2.4 IOS. I'm new to ASA/Firewall. I need to do access webserver from outside network.From Laptop (192.168.2.51), If I connect to url... it should open page from 10.10.10.50.I also need to ssh to webserver from laptop. If I ssh to 192.168.2.50 from laptop, it should connect to 10. 10. 10.50. [code]I can't get to webserver from outside network, so now, I connected laptop to directly ASA 5520 outside port with crossover cable.ASA Inside port connects to L3 switch. Webserver also connects to L3 switch. But still doesn't work.
View 9 Replies
View Related
Mar 3, 2012
I have added an ASA 5510 to my network between the Internet and a Windows 2008R2 server running ForeFront TMG. Before the ASA was added, vpn clients using Microsoft Windows 7 vpn client using L2TP/IPsec connected to our vpn. After ASA was added, clients can no longer connect. I would like to know how to configure the ASA to forward the vpn requests to the ForeFront TMG server for authentication and access to internal network resources. Mail is forwarded appropriately through the ASA to internal mail server and Internet access for LAN users works just fine.
Topology:
ASA 5510 (outside interface is ISP IP address, inside interface is 192.168.1.1)................Forefront TMG (outside nic 192.168.1.2, inside nic is LAN gateway IP address).
I have altered the registry key of the client vpn pc's per Microsoft Technet URL
View 1 Replies
View Related
Dec 16, 2010
I'm trying to set up Windows Server UAG for Direct Access in a Testlab. The UAG Server has two network nics. One in my Testdomain (internal) and the other one in a DMZ of our Cisco ASA (external).Our ASA dmz has subnet 192.168.3.x but UAG Direct Access needs public ip adresses.Is there documentation how to configure an ASA 5520 Firewall so i can use my Windows UAG Server with Direct Access?
View 7 Replies
View Related
Mar 28, 2013
I have WRT54GL v1.1 with last firmware. How to specify L2TP server by domain name? I see only fields for IP.
View 4 Replies
View Related
Jul 24, 2011
how do I pass from domain server , my network in our compant have ISA server and they close some website like face book , how can I pass over ISA server and use my websites?
View 3 Replies
View Related
Dec 8, 2012
I have an ASA 5520 with a DMZ with private addresses that I SNAT to my outside network. From inside the DMZ I can reach servers by both the internal private IP and the public IP, except if the IP is from the server trying to connect. So, say I have server1 and server2. I can connect from server1 to server 2 with both public and private, but can't connect from server1 to server1' using the public IP. ASA logs show that packets are being denied due to land attack. DNS doctoring is not an option for me.
View 1 Replies
View Related
Jul 7, 2012
i have user connected to office using Cisco vpn client , Cisco asa 5520 acts as vpn gateway, frequently the users got disconnected from the server while the VPN still established and not disconnected!
what is the cause of the issue , where the fault is located ? how to start the troubleshooting to figure out the issue?
View 1 Replies
View Related
Apr 17, 2011
For the moment we run a Nortel VPN server at work and I have on my laptop the Nortel VPN client. While I could connect through when I had my Linksys E2000 connected up now I can't after I replaced it with the 5505. (running 8.4(1).) what I should do on my 5505 so I can allow the nortel client to connect out?
View 6 Replies
View Related
Mar 3, 2013
I have a 5520 in production at a customer's site between an outside 802.11 network and an inside server. The server can get to outside hosts OK, and the traffic is being NATed properly, and sockets initiated by the server on the inside can pass data both ways, but I need to allow outside hosts the ability to send 'announcement' UDP packets to the inside server. I thought this might be an outside-NAT-required issue to get the traffic routed, but I need the inside server to see the actual outside host source IP in the UDP packet, so I basically set the outside host up similar to the inside host, just without the NAT table on the firewall -- it's subnet is outside the destination (inside server) subnet, and its gateway is the outside interface of the ASA, the same way the inside server is able to get to hosts outside. The firewall should just route the packet with a destination of the inside subnet once it sees that it hits a 'permit' ACL.
I have the appropriate ACL's set up, and when I do 'show access-list' I see policy hits for the 'permit' statements where the outside host is generating the announcement and it's hitting the ACL. I even duplicated the ACL into list 101 and 102, and applied 101 for inbound traffic on the outside int, and applied 102 for outbound traffic on the inside int, and I'm seeing policy hits on both permit statements outside and inside, so it looks like the traffic is being passed on to the inside interface and permitted, but the server isn't seeing the packets.
I can ping the outside interface from the outside, but cannot ping the inside interface or any inside hosts from the outside, even though I have 'permit icmp any any' enabled on the ACL on both ints. When I remove the firewall and put the outside clients on the same subnet, the server sees the packets just fine.
I set up the same scenario in my lab with an ASA 5505, with the same results. Below is the running config from the 5505 in the lab. The production firewall is running a slightly older version of ASA, so I made the configuration as basic as possible on the 5505 to match the config in the field:
: Saved
:
ASA Version 8.3(1)
!
hostname ciscoasa
enable password Guh9Xxhb9mcC8lV1 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan2
description Outside WAN Interface
nameif outside
security-level 0
ip address 192.168.10.1 255.255.255.0
!
interface Vlan3
description Inside LAN Interface
nameif inside(code)
View 6 Replies
View Related
Mar 6, 2012
I want to pass my client VPN request to MS Win Server 2003 - on FW I forwarded port for PPTP service to my server address, but on client side I get an error 619. On Cisco RV120W I have Site-to-Site VPN tunnel which works fine, PPTP server on Cisco is disabled. What should I do to pass VPN request to my LAN server to handle it?
View 4 Replies
View Related
May 24, 2012
I'm having some trouble with my P660RU-T1 configuration. I have recently set up a linux SFTP server at my home and am trying to access it via my public ip (eg 1.1.1.1), the problem is this public IP goes to the router which doesnt pass on the requests to the server.Last summer when i first messed around with this i had no problems with using the public ip to access the server, its only recently.
View 1 Replies
View Related
Jul 6, 2011
I have configure L2TP vpn using ASDM and now i am not able to connect my Cisco ASA 5505. it's showing error message 3Jul 07 201118:57:38IP = *.*.*.*, Error processing payload: Payload ID: 1
View 1 Replies
View Related
May 25, 2011
I have a Windows 2003 server running a L2TP VPN server on it. I'm putting theASA5505 in replacement of an open source firewall.
My question is that, I can't seem to forward the ports correctly for L2TP to the internal address of the 2k3 VPN server. It seems to me that the ASA is trying to negotiate the VPN connection rather than forward it internally.
Cisco ASA5505
WAN 216.136.1.2
LAN 10.1.1.1/24
Windows server - 10.1.1.14
I've added the NAT and ACL and still nothing.
View 2 Replies
View Related
Jul 17, 2011
I have a Cisco ASA 5505 Firewall. I am using windows VPN. I have configure IPSEC/L2TP Vpn. And now i hv some problem..
1) VPN is connected but I notices that VPN client connection gets in "HANG" mode after couple of minutes.
2) I am getting error when i try to connect my SQL Server (windows 2008) [code]
View 2 Replies
View Related
Dec 21, 2010
I'm trying to setup a L2TP VPN Connection on my ASA 5510 to connect with Android/Windows (Native Clients).I'm using the newest Releases:Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.3(5)
My asa config just the interesting part:
crypto ipsec transform-set trans esp-3des esp-sha-hmac crypto ipsec transform-set trans mode transportcrypto ipsec security-association lifetime seconds 28800crypto ipsec security-association lifetime kilobytes 4608000crypto dynamic-map dyno 10 set transform-set transcrypto map vpn 20 ipsec-isakmp dynamic dynocrypto map vpn interface outsidecrypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400no crypto isakmp nat-traversal
[code]....
If i try to connect with a Windows 7 Client (NOT behind NAT) I get the Error 691.
I see that Phase 1/2 are working with debug:
Dec 22 16:32:16 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 1 COMPLETED
Dec 22 16:51:25 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 2 COMPLETED (msgid=00000001)
Then I see this "Error":
Dec 22 16:51:26 [IKEv1]: Group = DefaultRAGroup, IP = XXXXX, Session is being torn down. Reason: L2TP initiated
I don't understand why it doens't work....I tried many templates from the net but nothings works.
View 5 Replies
View Related
