I have a Cisco ASA 5505 Firewall. I am using windows VPN. I have configure IPSEC/L2TP Vpn. And now i hv some problem..
1) VPN is connected but I notices that VPN client connection gets in "HANG" mode after couple of minutes.
2) I am getting error when i try to connect my SQL Server (windows 2008) [code]
I’m configuring a L2TP IPSEC VPN on a 5505 asa so that windows 7 clients can natively connect. It connects correctly during Phase 1 and 2, but I can’t ping anything or access resources on the internal network. This is my first time working with an ASA.
Master# sh run
: Saved
:
ASA Version 8.2(2)
!
hostname Master
domain-name service.local
[code]....
I'm trying to setup a L2TP VPN Connection on my ASA 5510 to connect with Android/Windows (Native Clients).I'm using the newest Releases:Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.3(5)
My asa config just the interesting part:
crypto ipsec transform-set trans esp-3des esp-sha-hmac crypto ipsec transform-set trans mode transportcrypto ipsec security-association lifetime seconds 28800crypto ipsec security-association lifetime kilobytes 4608000crypto dynamic-map dyno 10 set transform-set transcrypto map vpn 20 ipsec-isakmp dynamic dynocrypto map vpn interface outsidecrypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400no crypto isakmp nat-traversal
[code]....
If i try to connect with a Windows 7 Client (NOT behind NAT) I get the Error 691.
I see that Phase 1/2 are working with debug:
Dec 22 16:32:16 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 1 COMPLETED
Dec 22 16:51:25 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 2 COMPLETED (msgid=00000001)
Then I see this "Error":
Dec 22 16:51:26 [IKEv1]: Group = DefaultRAGroup, IP = XXXXX, Session is being torn down. Reason: L2TP initiated
I don't understand why it doens't work....I tried many templates from the net but nothings works.
I have configure L2TP vpn using ASDM and now i am not able to connect my Cisco ASA 5505. it's showing error message 3Jul 07 201118:57:38IP = *.*.*.*, Error processing payload: Payload ID: 1
View 1 Replies View RelatedI'm trying to setup a L2TP over IPSEC vpn connection on a PIX 501 that will use key sharing. In addition, I have a PPTP connection setup which allows connectivity. Two things, the L2TP vpn client I am using does not connect and times out. The second is that the PPTP client I use does connect, but cannot ping any resources on the network.
The config on the PIX is below:
Building configuration...
: Saved
:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password tdkuTUSh53d2MT6B encrypted
[ Code] .....
I am trying to get a L2TP/IPSEC VPN going on one of my servers behind the DIR655 router I have used Port Forwarding and Virtual Server and neithere seem to allow these ports to be open in either situation a port scan shows the ports closed..My ISP (Comcast) does not block these ports?
View 14 Replies View RelatedI had my PPTP VPN working great at my old place, now that I moved I also upgraded my speed which means I got a different 2Wire. This 2Wire can only do DMZ mode and can't bridge. ( I tried everything, including the mdc page, no go). This works fine apart from blocking GRE somehow. I'm using a Mikrotik RB450G as my PPTP server. Does L2TP or IPSEC use the GRE protocol?
View 1 Replies View RelatedI have a stable l2tp/ipsec config that I have been using for many years with the Windows XP native VPN client and the iPhone VPN client.This configuration does not seem to work with the native Windows 7 VPN client. What has changed between XP and 7 on the native VPN client front? I'm running IOS 12.4(15)T5.
View 1 Replies View RelatedI have a Cisco 7200 and need to establish L2TP over IPSEC session with a Draytek Fly200. Draytek must use L2TP over IPSEC to provide LAN-to-LAN connectivity. IPSEC phase 1 and 2 is ok, L2TP tunnel is also established, but on cloned virtual-access IPCP negotiation is not completed:
*Sep 16 09:50:36.911: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state to up
L2X_ADJ: Vi3:midchain adj reqd for ip 0.0.0.0, cid 0
*Sep 16 09:50:38.911: Vi3 IPCP: O CONFREQ [REQsent] id 2 len 10
*Sep 16 09:50:38.911: Vi3 IPCP: Address 192.168.176.2 (0x0306C0A8B002)
*Sep 16 09:50:38.911: Vi3 IPCP: Event[Timeout+] State[REQsent to REQsent]
I think my VPDN configuration from Cisco side is not correct, but I cannot find configuration examples for this kind of solution.
I have a 5510 that i have configured for L2TP over IPSEC, not using AnyConnect. The first, and most prevelant being, VPN clients are unable to ping/access any of the hosts that are assigned a static NAT from the inside interface to the outside interface. I was able to circumvent this by adding another static NAT to the public interface for the incoming clients, but this caused intermittent connectivity issues with inside hosts. The second issue involves DNS. I have configured two DNS servers, both of which reside on the internal network and are in the split_tunnel ACL for VPN clients, but no clients are using this DNS. What is the workaround for using split tunneling AND internal DNS servers, if any?
i've had two different CCNA's look at this numerous times to no avail. A ping from a VPN client to any internal host works fine, unless it is one that is NAT'd. You can see in the config where i added the extra STATIC NAT to try and fix the issue. And this works perfectly across the tunnel but only intermittenly from the internal 10.1.4.x network. [code]
Co-worker just got a Blackberry Playbook tablet and, try as I might, we cannot get the darn thing to successfully set up a working IPSEC/L2TP vpn tunnel to our ASA 5510, which acts as a multi-purpose VPN concentrator. Any luck setting up L2TP/IPSEC VPN to ASA from Blackberry Playbook?
View 0 Replies View RelatedI'm opening a new topic related to my problem with the VPN connection, to avoid confusion, since there are many, in the old information, no longer required.
I would like to configure my ASA5510 L2PT/IpSec to accept connections from Windows clients. I happen to authenticate via AD credentials. When I try to connect is because the error 691. I enabled debugging on the machine the following:
debug crypto isakmp 3
debug crypto ipsec 3
debug ldap 255
Successfull in setting up an L2TP/IPsec tunnel through NAT-T against a Windows 2008/ R2 RRAS server? I am using an 881 router and the layout is someting like this:Client -> 881 -> NAT -> internet -> Windows 2008 RRAS.The tunnel goes form the 881 to the Windows server (not from the client...).
View 4 Replies View Relatedi have configure l2tp/ipsec vpn on cisco ASA 5520 and also configure windows 7 client but its getting error
Error in ASA debug log
debug crypto isakmp 7
Mar 26 07:44:28 [IKEv1]: IP = 59.161.130.13, IKE_DECODE RECEIVED Message
[Code]......
i am now trying to configure a Cisco Small Business Pro SRP 521w router for a branch office, i am trying to get the router to connect to a L2TP VPN server inside my datacenter, but seems to me like L2TP VPN client function is not supported inside the SRP 521w router.
Can Cisco implement L2TP VPN client into the firmware for the SRP 521w router in the future ?
i configurated ipsec vpn at cisco asa 5510. all them are working very well. now i want to change ipsec remote vpn to L2tp over ipsec.i have router, asa and 3750 switch. all nat translation are done at router , ipsec vpn configurate at asa.
this is my ipsec configuration. this is working config. as you see i do static nat asa outside ip for vpn at router. now i want l2tp over ipsec. before i do it i have some question
1. must i do static nat port udp 1701 for l2tp over ipsec vpn? can i write access list at asa to open port 1701?
2. can i remove this static nat or i can not be change anything.is this nat is true for l2tp over ipsec vpn?
3.as you see user authentication from radius server at ipsec vpn. i also want this is same as l2tp over ipsec vpn..
4. i think that i must be add this addtional config. is this true? tunnel-group DefaultRAGroup ppp-attributesno authentication chapauthentication ms-chap-v2
is this config enougth for l2tp over ipsec vpn?? what is addtional config i need?
Any good vpn config for a router to allow vpn connections from Android phones using L2TP-IPSEC? Router is an 1841 running most current IOS ver 15.1.
View 1 Replies View RelatedI'm having problem establish l2tp/ipsec vpn connection from Windows vista/7 vpn client to cisco 1921 ( ios 15.2 )
C1 --------> (internet cloud) ---------> (cisco 1921)----->LAN
Error that I'm retrieving is always the same: Error 789: "The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer"
But I'm able to establish l2tp/ipsec vpn connection to the same vpn server with my iPhone 4.
Below is isakmp debug log from lns router(cisco 1921) when I've tried to establish vpn with windows client. Anything useful from these logs to point me on the right direction to finally solve this problem with windows clients.
#debug crypto isakmp
*Apr 8 10:56:47.018: ISAKMP (0): received packet from 186.51.43.137 dport 500 sport 987 Global (N) NEW SA
*Apr 8 10:56:47.018: ISAKMP: Created a peer struct for 186.51.43.137, peer port 987
*Apr 8 10:56:47.018: ISAKMP: New peer created peer = 0x3296C24C peer_handle = 0x80000068
[Code]...
We have ASA 5520 running 8.2(3) software and we're trying to make Remote Access VPN (l2tp/ipsec) working from Android. We succeeded in making IPSEC tunnel (ending "Phase 2 completed"), but we cannot make L2TP tunnel working.We're using RADIUS for L2TP authentication, but ASA doesn't even try to check credentials entered by use. The same set of credentials entered on Windows {XP, VISTA, 7, Mobile} works ok. Which debugging options should we turned on?
View 3 Replies View RelatedIs it possible to configure Layer 2 Tunneling Protocol (L2TP) over IPsec on a cisco router like 1921 ISR? This link shows basically what i want to achieve but instead of an ASA, i would like to use just a router with sec..
[URL]
I have added an ASA 5510 to my network between the Internet and a Windows 2008R2 server running ForeFront TMG. Before the ASA was added, vpn clients using Microsoft Windows 7 vpn client using L2TP/IPsec connected to our vpn. After ASA was added, clients can no longer connect. I would like to know how to configure the ASA to forward the vpn requests to the ForeFront TMG server for authentication and access to internal network resources. Mail is forwarded appropriately through the ASA to internal mail server and Internet access for LAN users works just fine.
Topology:
ASA 5510 (outside interface is ISP IP address, inside interface is 192.168.1.1)................Forefront TMG (outside nic 192.168.1.2, inside nic is LAN gateway IP address).
I have altered the registry key of the client vpn pc's per Microsoft Technet URL
I am trying to configure an IPSEC vpn on an ASA5505 I setup an SSL vpn and it works fine, I can browse to the https: address log in and connnect to servers However when I try to setup the ipsec client access vpn it will not connect and I am getting the errors below I used the wizard for the initial configuration Looks like the inital IKE is being blocked or dropped?
%ASA-7-710005: UDP request discarded from my external IP/35781 to external:ASA-external/500
%ASA-7-710005: UDP request discarded from my external IP/35781 to external:ASA-external/137
A customer has a 5505. According to the datasheet the limit of IPSEC sessions is 25 and the limit of anyconnect sessions is 25. Does that mean I can have 25 IPSEC tunnels and 25 Anyconnect tunnels at the same time? The customer needs at least 50 concurrent tunnels on his ASA. Am I understanding it correctly?
I was thinking the customer could pay for the anyconnect essentials license and connect his anyconnect clients to the ASA. Is that a good option to get the 50 concurrent clients connected?
We currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
View 13 Replies View RelatedWe currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
View 1 Replies View RelatedI currently have a problem where I have to constantly reboot my ASA whenever my cable modem reboots. The ISP (Pen Tele Data) is setup so that my ASA has to obtain its' static IP using dhcp (ip address dhcp setroute) on the outside interface. Now, I also have another location with a cable connection (Comcast) that does NOT experience the same problem. However, the difference is this ISP allows me to assign my static IP directly on my outside interface. What can I do so that I don't have to reboot my first ASA everytime modem reboots.
View 6 Replies View RelatedThere is so much mis-information on the Internet and Cisco's own support site has bits and pieces everywhere (I've found at least 5 support pages in Cisco that address this subject), none work or are directly targeted at what I would consider is a major use case for this product. I can see from the many posts everywhere that getting L2TP/IPSEC to work is a major problem, requiring many configuration steps that all have to be perfect and there seems to be some trick to get it to work that most people struggle with. Most of the advice out there is impertinent and highly technical but doesn't work.
I would like to know if there is any consolidated instructions that WORK to create a VPN server on the 5505 using the ASDM and also how to set your Windows 7 (or 2008) client to work with it.
Like I've said, I've spent hours and hours on this and have yet to get anything to work. I have a brand new 5505 connected directly to DSL (static IP) that I ran the wizard on and followed the best advice I could find (by the way there's TONS of information on getting XP to work but afaik, this does NOT work for windows 7). Now that I've tried various things without success, I believe I've gotten it so fouled up I need to reset to factory defaults and start over.
I also have another brand new 5505 connected to a different DSL line. Behind that firewall, I have both windows 7 clients and windows 2008 server. I've tried lots of different things to get these to work including the registry hacks (which, if indeed is required, I seriously can't believe that Cisco hasn't given us a tool for).
I have tried to use the ASDM to do all my programming as I find the CLI to be extremely error prone and virtually incomprehensible.So, what the world needs is one place that gives all the instructions on what to do, step-by-step that really work for this simple use case of windows connecting to the ASA.
I am now going to configure IPSec VPN connection for Cisco ASA 5505 (Version 8.4)
View 3 Replies View RelatedCisco ASA 5505 ver 8.4. Most things work but now I want to setup a vpn connection..I have done this 2 ways, first by using the "VPN Wizard" in ASDM and then 5 hours later removing everything and configuring from cli. And it just doesn't work, client (WinXP & Win7) gets "error 792" and sometimes "error 789" (both indicating problem with phase 1, I'm pretty sure of that) Googling on those gives a few suggestions none works. All I get in the log on Cisco is the "Error processing payload: Payload ID: 1" Google on that only comes up with a few pages telling me this message is caused by an error. (Yeah, I could never have guessed...) For the cli config, I followed this tutorial carefully (3 times actually...) url...I'm using PSK for IPSec, entered same on Cisco and client - checked several times, this is not a password/PSK issue. Ports opened on Cisco: 500, 1701, 4500 (For a try I opened all ports, no change.) And here's the "show run". [code]
View 2 Replies View RelatedI want to be able to gather some time metrics based on source IP, and destination port. Is it possiable to track how much time a user spends using a service based on it's port number. I have figured out how to capture all the data, and I can then look at timestamps, but I would like a better way if possible. Can this be done at the firewall, or do I need a different appliance?
View 1 Replies View RelatedI have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
All these remote networks are at the Main Site Clavister Firewall.
I have a Windows 2003 server running a L2TP VPN server on it. I'm putting theASA5505 in replacement of an open source firewall.
My question is that, I can't seem to forward the ports correctly for L2TP to the internal address of the 2k3 VPN server. It seems to me that the ASA is trying to negotiate the VPN connection rather than forward it internally.
Cisco ASA5505
WAN 216.136.1.2
LAN 10.1.1.1/24
Windows server - 10.1.1.14
I've added the NAT and ACL and still nothing.
I set up an IPSec VPN with NAT-T between two cisco router 871. In particular one router acts as a SERVER and the other one as a CLIENT. All the traffic coming from the hosts connected to the CLIENT-router is sent over the VPN (no split tunnel). Everything works perfectly. The only problem is the amount of time the VPN takes to establish the first connection between the two routers. In particular it takes about two minutes. tell me if this amount of time can be reduced (with a partcular configuration instruction)? Or this is the minimum amount of time required for the first connection establishment?
View 1 Replies View Related