I had my PPTP VPN working great at my old place, now that I moved I also upgraded my speed which means I got a different 2Wire. This 2Wire can only do DMZ mode and can't bridge. ( I tried everything, including the mdc page, no go). This works fine apart from blocking GRE somehow. I'm using a Mikrotik RB450G as my PPTP server. Does L2TP or IPSEC use the GRE protocol?
View 1 RepliesIs it possible to configure Layer 2 Tunneling Protocol (L2TP) over IPsec on a cisco router like 1921 ISR? This link shows basically what i want to achieve but instead of an ASA, i would like to use just a router with sec..
[URL]
The router 861 Fast ethernet have support for wan protocol L2TP ?
Can I configure the router to use L2TP wan protocol to communicate the wan FE port to my ISP ?
If yes wath is the way ( CLI or Cisco E[press Professional Configurator ?)
What Is Maximal Speed For E4200 l2tp Protocol.
View 1 Replies View RelatedI am trying to get a L2TP/IPSEC VPN going on one of my servers behind the DIR655 router I have used Port Forwarding and Virtual Server and neithere seem to allow these ports to be open in either situation a port scan shows the ports closed..My ISP (Comcast) does not block these ports?
View 14 Replies View RelatedI'm trying to setup a L2TP over IPSEC vpn connection on a PIX 501 that will use key sharing. In addition, I have a PPTP connection setup which allows connectivity. Two things, the L2TP vpn client I am using does not connect and times out. The second is that the PPTP client I use does connect, but cannot ping any resources on the network.
The config on the PIX is below:
Building configuration...
: Saved
:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password tdkuTUSh53d2MT6B encrypted
[ Code] .....
I have a stable l2tp/ipsec config that I have been using for many years with the Windows XP native VPN client and the iPhone VPN client.This configuration does not seem to work with the native Windows 7 VPN client. What has changed between XP and 7 on the native VPN client front? I'm running IOS 12.4(15)T5.
View 1 Replies View RelatedI have a Cisco 7200 and need to establish L2TP over IPSEC session with a Draytek Fly200. Draytek must use L2TP over IPSEC to provide LAN-to-LAN connectivity. IPSEC phase 1 and 2 is ok, L2TP tunnel is also established, but on cloned virtual-access IPCP negotiation is not completed:
*Sep 16 09:50:36.911: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state to up
L2X_ADJ: Vi3:midchain adj reqd for ip 0.0.0.0, cid 0
*Sep 16 09:50:38.911: Vi3 IPCP: O CONFREQ [REQsent] id 2 len 10
*Sep 16 09:50:38.911: Vi3 IPCP: Address 192.168.176.2 (0x0306C0A8B002)
*Sep 16 09:50:38.911: Vi3 IPCP: Event[Timeout+] State[REQsent to REQsent]
I think my VPDN configuration from Cisco side is not correct, but I cannot find configuration examples for this kind of solution.
I have a 5510 that i have configured for L2TP over IPSEC, not using AnyConnect. The first, and most prevelant being, VPN clients are unable to ping/access any of the hosts that are assigned a static NAT from the inside interface to the outside interface. I was able to circumvent this by adding another static NAT to the public interface for the incoming clients, but this caused intermittent connectivity issues with inside hosts. The second issue involves DNS. I have configured two DNS servers, both of which reside on the internal network and are in the split_tunnel ACL for VPN clients, but no clients are using this DNS. What is the workaround for using split tunneling AND internal DNS servers, if any?
i've had two different CCNA's look at this numerous times to no avail. A ping from a VPN client to any internal host works fine, unless it is one that is NAT'd. You can see in the config where i added the extra STATIC NAT to try and fix the issue. And this works perfectly across the tunnel but only intermittenly from the internal 10.1.4.x network. [code]
Co-worker just got a Blackberry Playbook tablet and, try as I might, we cannot get the darn thing to successfully set up a working IPSEC/L2TP vpn tunnel to our ASA 5510, which acts as a multi-purpose VPN concentrator. Any luck setting up L2TP/IPSEC VPN to ASA from Blackberry Playbook?
View 0 Replies View RelatedI'm opening a new topic related to my problem with the VPN connection, to avoid confusion, since there are many, in the old information, no longer required.
I would like to configure my ASA5510 L2PT/IpSec to accept connections from Windows clients. I happen to authenticate via AD credentials. When I try to connect is because the error 691. I enabled debugging on the machine the following:
debug crypto isakmp 3
debug crypto ipsec 3
debug ldap 255
Successfull in setting up an L2TP/IPsec tunnel through NAT-T against a Windows 2008/ R2 RRAS server? I am using an 881 router and the layout is someting like this:Client -> 881 -> NAT -> internet -> Windows 2008 RRAS.The tunnel goes form the 881 to the Windows server (not from the client...).
View 4 Replies View Relatedi have configure l2tp/ipsec vpn on cisco ASA 5520 and also configure windows 7 client but its getting error
Error in ASA debug log
debug crypto isakmp 7
Mar 26 07:44:28 [IKEv1]: IP = 59.161.130.13, IKE_DECODE RECEIVED Message
[Code]......
i am now trying to configure a Cisco Small Business Pro SRP 521w router for a branch office, i am trying to get the router to connect to a L2TP VPN server inside my datacenter, but seems to me like L2TP VPN client function is not supported inside the SRP 521w router.
Can Cisco implement L2TP VPN client into the firmware for the SRP 521w router in the future ?
i configurated ipsec vpn at cisco asa 5510. all them are working very well. now i want to change ipsec remote vpn to L2tp over ipsec.i have router, asa and 3750 switch. all nat translation are done at router , ipsec vpn configurate at asa.
this is my ipsec configuration. this is working config. as you see i do static nat asa outside ip for vpn at router. now i want l2tp over ipsec. before i do it i have some question
1. must i do static nat port udp 1701 for l2tp over ipsec vpn? can i write access list at asa to open port 1701?
2. can i remove this static nat or i can not be change anything.is this nat is true for l2tp over ipsec vpn?
3.as you see user authentication from radius server at ipsec vpn. i also want this is same as l2tp over ipsec vpn..
4. i think that i must be add this addtional config. is this true? tunnel-group DefaultRAGroup ppp-attributesno authentication chapauthentication ms-chap-v2
is this config enougth for l2tp over ipsec vpn?? what is addtional config i need?
Any good vpn config for a router to allow vpn connections from Android phones using L2TP-IPSEC? Router is an 1841 running most current IOS ver 15.1.
View 1 Replies View RelatedI'm having problem establish l2tp/ipsec vpn connection from Windows vista/7 vpn client to cisco 1921 ( ios 15.2 )
C1 --------> (internet cloud) ---------> (cisco 1921)----->LAN
Error that I'm retrieving is always the same: Error 789: "The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer"
But I'm able to establish l2tp/ipsec vpn connection to the same vpn server with my iPhone 4.
Below is isakmp debug log from lns router(cisco 1921) when I've tried to establish vpn with windows client. Anything useful from these logs to point me on the right direction to finally solve this problem with windows clients.
#debug crypto isakmp
*Apr 8 10:56:47.018: ISAKMP (0): received packet from 186.51.43.137 dport 500 sport 987 Global (N) NEW SA
*Apr 8 10:56:47.018: ISAKMP: Created a peer struct for 186.51.43.137, peer port 987
*Apr 8 10:56:47.018: ISAKMP: New peer created peer = 0x3296C24C peer_handle = 0x80000068
[Code]...
We have ASA 5520 running 8.2(3) software and we're trying to make Remote Access VPN (l2tp/ipsec) working from Android. We succeeded in making IPSEC tunnel (ending "Phase 2 completed"), but we cannot make L2TP tunnel working.We're using RADIUS for L2TP authentication, but ASA doesn't even try to check credentials entered by use. The same set of credentials entered on Windows {XP, VISTA, 7, Mobile} works ok. Which debugging options should we turned on?
View 3 Replies View RelatedI have a Cisco ASA 5505 Firewall. I am using windows VPN. I have configure IPSEC/L2TP Vpn. And now i hv some problem..
1) VPN is connected but I notices that VPN client connection gets in "HANG" mode after couple of minutes.
2) I am getting error when i try to connect my SQL Server (windows 2008) [code]
I'm trying to setup a L2TP VPN Connection on my ASA 5510 to connect with Android/Windows (Native Clients).I'm using the newest Releases:Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.3(5)
My asa config just the interesting part:
crypto ipsec transform-set trans esp-3des esp-sha-hmac crypto ipsec transform-set trans mode transportcrypto ipsec security-association lifetime seconds 28800crypto ipsec security-association lifetime kilobytes 4608000crypto dynamic-map dyno 10 set transform-set transcrypto map vpn 20 ipsec-isakmp dynamic dynocrypto map vpn interface outsidecrypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400no crypto isakmp nat-traversal
[code]....
If i try to connect with a Windows 7 Client (NOT behind NAT) I get the Error 691.
I see that Phase 1/2 are working with debug:
Dec 22 16:32:16 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 1 COMPLETED
Dec 22 16:51:25 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 2 COMPLETED (msgid=00000001)
Then I see this "Error":
Dec 22 16:51:26 [IKEv1]: Group = DefaultRAGroup, IP = XXXXX, Session is being torn down. Reason: L2TP initiated
I don't understand why it doens't work....I tried many templates from the net but nothings works.
I have added an ASA 5510 to my network between the Internet and a Windows 2008R2 server running ForeFront TMG. Before the ASA was added, vpn clients using Microsoft Windows 7 vpn client using L2TP/IPsec connected to our vpn. After ASA was added, clients can no longer connect. I would like to know how to configure the ASA to forward the vpn requests to the ForeFront TMG server for authentication and access to internal network resources. Mail is forwarded appropriately through the ASA to internal mail server and Internet access for LAN users works just fine.
Topology:
ASA 5510 (outside interface is ISP IP address, inside interface is 192.168.1.1)................Forefront TMG (outside nic 192.168.1.2, inside nic is LAN gateway IP address).
I have altered the registry key of the client vpn pc's per Microsoft Technet URL
I’m configuring a L2TP IPSEC VPN on a 5505 asa so that windows 7 clients can natively connect. It connects correctly during Phase 1 and 2, but I can’t ping anything or access resources on the internal network. This is my first time working with an ASA.
Master# sh run
: Saved
:
ASA Version 8.2(2)
!
hostname Master
domain-name service.local
[code]....
I have a strange issue where im able to get an ipsec tunnel from tha cisco 1841 to a linksys/cisco RV016 for about a minute and ping/encrypt packets across the lin for about a minute before it goes down. I tried various configuration and it all results in the tunnel coming up for a minute then going down. I'm not sure if im hitting a bug and on which decide of if im doing something wrong.
RV016 firmware 2.0.18
cisco 1841: C1841-ADVENTERPRISEK9-M), Version 12.4(24)T
my config
no crypto isakmp default policy
!
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
[code]....
We have tried a variety of options in an attempt to use Load Balancing (Protocol Binding) with an RV082 that has a site to site IPsec tunnel with another RV082. Both are v3.
Here is the issue. We have dual ISPs, one has great bandwidth, but we incur overages. The other has mediocre bandwidth, but has unlimited usage.
GROUP1 - We want most PCs to use the "unlimited" ISP for general surfing, email, etc. (Bound all ports for range of internal IPs to ANY dest to WAN1)
GROUP2 - We want to use the "faster" ISP for our VPN tunnel (mostly RDP and SIP traffic). (Bound all ports for range of internal IPs to ANY dest to WAN2)
So far everything works. The router will route traffic appropriately and GROUP 1 uses WAN1 and GROUP 2 uses WAN2.
Unfortunately, sometimes GROUP1 users need access to resources over the VPN (WAN2).
There is something not right with the routing. For example GROUP1 can ping and receive responses from devices on the other side of the tunnel, but GROUP1 can't access intranet sites on the other side of the tunnel. They also can't RDP to PCs on the other side of the tunnel.
Why does the router correctly route ICMP, but not RDP?
We've tried adding additional protocol binding rules for specific ports(80, 3389, etc) and ip ranges (both local and remote) to see if we could force GROUP1 traffic destined via VPN through WAN2, but it doesn't work.
Shouldn't VPN tunnels created and configured in the RVs not adhere to protocol binding? It just seems logical to me, but maybe I am missing something.
I would like to allow my remote users to access all resources behind the ASA and my remote branches. Here is my setup. ASA5510 as hub at data-center.
Internal network 172.21.x.x Directly connected
DMZ 172.22.1.x.x Directly Connected
Branch1 10.47.x.x L2L VPN
Branch2 10.47.y.x L2L VPN
Remote users 172.21.y.x L2TP Windows Client
I can access my internal resources connected to the ASA but not the DMZ or branch offices. Do I need routing and reverse route injection?
I tried any type of combination and just couldn't make it works. Only PPTP works well. Whether Apple iOS IPSec VPN is supported or not?
View 11 Replies View RelatedI have two virtual machines (of Oracle VirtualBox). On one of them,I installed Windows Server 2003 and on the other I installed Windows XP (SP3). I made two VPN connections between them one is PPTP-based and another is L2TP-based. Now I want to transfer a file from the server side to the client side (Windows XP) once using the PPTP-based VPN connection, and again using the L2TP-based VPN connection. And by using the network monitor (protocol analyzer), I have to determine which protocol is more secure than the other.how to know which one is more secure using the network monitor?
View 1 Replies View RelatedIs it possible to pass 802.3 packets over a L2TP?If so, how would the tunnel differ from a normal L2TP?
View 1 Replies View RelatedThere is so much mis-information on the Internet and Cisco's own support site has bits and pieces everywhere (I've found at least 5 support pages in Cisco that address this subject), none work or are directly targeted at what I would consider is a major use case for this product. I can see from the many posts everywhere that getting L2TP/IPSEC to work is a major problem, requiring many configuration steps that all have to be perfect and there seems to be some trick to get it to work that most people struggle with. Most of the advice out there is impertinent and highly technical but doesn't work.
I would like to know if there is any consolidated instructions that WORK to create a VPN server on the 5505 using the ASDM and also how to set your Windows 7 (or 2008) client to work with it.
Like I've said, I've spent hours and hours on this and have yet to get anything to work. I have a brand new 5505 connected directly to DSL (static IP) that I ran the wizard on and followed the best advice I could find (by the way there's TONS of information on getting XP to work but afaik, this does NOT work for windows 7). Now that I've tried various things without success, I believe I've gotten it so fouled up I need to reset to factory defaults and start over.
I also have another brand new 5505 connected to a different DSL line. Behind that firewall, I have both windows 7 clients and windows 2008 server. I've tried lots of different things to get these to work including the registry hacks (which, if indeed is required, I seriously can't believe that Cisco hasn't given us a tool for).
I have tried to use the ASDM to do all my programming as I find the CLI to be extremely error prone and virtually incomprehensible.So, what the world needs is one place that gives all the instructions on what to do, step-by-step that really work for this simple use case of windows connecting to the ASA.
A office use Windows Server 2008 R2 (routing and remote access) for user VPN connection.At other location B office, I want to setup a router (RV120W Wireless-N VPN Firewall) for L2TP VPN connect to A office.B office use ADSL dial connection, and set a Dynamic DNS for the router. how to configuration the L2TP VPN.
View 1 Replies View RelatedI have an 1921 that I use for L2TPv3 tunnel connection with 2 sides. I need to add others 2 sides and I thought to add an EHWIC-4ESG on my router. Can I configure different xconnections with this module? I would like to configure my router as below: [code]
View 1 Replies View Relatedi did in past a lot of L2TP connection between two end point. in this case ans with 2911 series with ios 15 and DATA license Activated. the l2tp session does not establishe between a this 2911 and 7209. Attached is topology file and bellow the configuration of both router.
PE 2911
l2tp-class l2-dyn
authentication
password 123456
[Code]....
I have configure L2TP vpn using ASDM and now i am not able to connect my Cisco ASA 5505. it's showing error message 3Jul 07 201118:57:38IP = *.*.*.*, Error processing payload: Payload ID: 1
View 1 Replies View Related