I'm opening a new topic related to my problem with the VPN connection, to avoid confusion, since there are many, in the old information, no longer required.
I would like to configure my ASA5510 L2PT/IpSec to accept connections from Windows clients. I happen to authenticate via AD credentials. When I try to connect is because the error 691. I enabled debugging on the machine the following:
I have a 5510 that i have configured for L2TP over IPSEC, not using AnyConnect. The first, and most prevelant being, VPN clients are unable to ping/access any of the hosts that are assigned a static NAT from the inside interface to the outside interface. I was able to circumvent this by adding another static NAT to the public interface for the incoming clients, but this caused intermittent connectivity issues with inside hosts. The second issue involves DNS. I have configured two DNS servers, both of which reside on the internal network and are in the split_tunnel ACL for VPN clients, but no clients are using this DNS. What is the workaround for using split tunneling AND internal DNS servers, if any?
i've had two different CCNA's look at this numerous times to no avail. A ping from a VPN client to any internal host works fine, unless it is one that is NAT'd. You can see in the config where i added the extra STATIC NAT to try and fix the issue. And this works perfectly across the tunnel but only intermittenly from the internal 10.1.4.x network. [code]
Co-worker just got a Blackberry Playbook tablet and, try as I might, we cannot get the darn thing to successfully set up a working IPSEC/L2TP vpn tunnel to our ASA 5510, which acts as a multi-purpose VPN concentrator. Any luck setting up L2TP/IPSEC VPN to ASA from Blackberry Playbook?
i configurated ipsec vpn at cisco asa 5510. all them are working very well. now i want to change ipsec remote vpn to L2tp over ipsec.i have router, asa and 3750 switch. all nat translation are done at router , ipsec vpn configurate at asa.
this is my ipsec configuration. this is working config. as you see i do static nat asa outside ip for vpn at router. now i want l2tp over ipsec. before i do it i have some question
1. must i do static nat port udp 1701 for l2tp over ipsec vpn? can i write access list at asa to open port 1701?
2. can i remove this static nat or i can not be change anything.is this nat is true for l2tp over ipsec vpn?
3.as you see user authentication from radius server at ipsec vpn. i also want this is same as l2tp over ipsec vpn..
4. i think that i must be add this addtional config. is this true? tunnel-group DefaultRAGroup ppp-attributesno authentication chapauthentication ms-chap-v2
is this config enougth for l2tp over ipsec vpn?? what is addtional config i need?
I'm trying to setup a L2TP VPN Connection on my ASA 5510 to connect with Android/Windows (Native Clients).I'm using the newest Releases:Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.3(5)
If i try to connect with a Windows 7 Client (NOT behind NAT) I get the Error 691.
I see that Phase 1/2 are working with debug: Dec 22 16:32:16 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 1 COMPLETED Dec 22 16:51:25 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 2 COMPLETED (msgid=00000001)
Then I see this "Error":
Dec 22 16:51:26 [IKEv1]: Group = DefaultRAGroup, IP = XXXXX, Session is being torn down. Reason: L2TP initiated
I don't understand why it doens't work....I tried many templates from the net but nothings works.
I have added an ASA 5510 to my network between the Internet and a Windows 2008R2 server running ForeFront TMG. Before the ASA was added, vpn clients using Microsoft Windows 7 vpn client using L2TP/IPsec connected to our vpn. After ASA was added, clients can no longer connect. I would like to know how to configure the ASA to forward the vpn requests to the ForeFront TMG server for authentication and access to internal network resources. Mail is forwarded appropriately through the ASA to internal mail server and Internet access for LAN users works just fine.
Topology:
ASA 5510 (outside interface is ISP IP address, inside interface is 192.168.1.1)................Forefront TMG (outside nic 192.168.1.2, inside nic is LAN gateway IP address).
I have altered the registry key of the client vpn pc's per Microsoft Technet URL
I'm trying to setup a L2TP over IPSEC vpn connection on a PIX 501 that will use key sharing. In addition, I have a PPTP connection setup which allows connectivity. Two things, the L2TP vpn client I am using does not connect and times out. The second is that the PPTP client I use does connect, but cannot ping any resources on the network.
The config on the PIX is below:
Building configuration... : Saved : PIX Version 6.3(3) interface ethernet0 auto interface ethernet1 100full nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password tdkuTUSh53d2MT6B encrypted [ Code] .....
I am trying to get a L2TP/IPSEC VPN going on one of my servers behind the DIR655 router I have used Port Forwarding and Virtual Server and neithere seem to allow these ports to be open in either situation a port scan shows the ports closed..My ISP (Comcast) does not block these ports?
I had my PPTP VPN working great at my old place, now that I moved I also upgraded my speed which means I got a different 2Wire. This 2Wire can only do DMZ mode and can't bridge. ( I tried everything, including the mdc page, no go). This works fine apart from blocking GRE somehow. I'm using a Mikrotik RB450G as my PPTP server. Does L2TP or IPSEC use the GRE protocol?
I have a stable l2tp/ipsec config that I have been using for many years with the Windows XP native VPN client and the iPhone VPN client.This configuration does not seem to work with the native Windows 7 VPN client. What has changed between XP and 7 on the native VPN client front? I'm running IOS 12.4(15)T5.
I have a Cisco 7200 and need to establish L2TP over IPSEC session with a Draytek Fly200. Draytek must use L2TP over IPSEC to provide LAN-to-LAN connectivity. IPSEC phase 1 and 2 is ok, L2TP tunnel is also established, but on cloned virtual-access IPCP negotiation is not completed:
*Sep 16 09:50:36.911: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state to up L2X_ADJ: Vi3:midchain adj reqd for ip 0.0.0.0, cid 0 *Sep 16 09:50:38.911: Vi3 IPCP: O CONFREQ [REQsent] id 2 len 10 *Sep 16 09:50:38.911: Vi3 IPCP: Address 192.168.176.2 (0x0306C0A8B002) *Sep 16 09:50:38.911: Vi3 IPCP: Event[Timeout+] State[REQsent to REQsent]
I think my VPDN configuration from Cisco side is not correct, but I cannot find configuration examples for this kind of solution.
Successfull in setting up an L2TP/IPsec tunnel through NAT-T against a Windows 2008/ R2 RRAS server? I am using an 881 router and the layout is someting like this:Client -> 881 -> NAT -> internet -> Windows 2008 RRAS.The tunnel goes form the 881 to the Windows server (not from the client...).
i am now trying to configure a Cisco Small Business Pro SRP 521w router for a branch office, i am trying to get the router to connect to a L2TP VPN server inside my datacenter, but seems to me like L2TP VPN client function is not supported inside the SRP 521w router.
Can Cisco implement L2TP VPN client into the firmware for the SRP 521w router in the future ?
I'm having problem establish l2tp/ipsec vpn connection from Windows vista/7 vpn client to cisco 1921 ( ios 15.2 ) C1 --------> (internet cloud) ---------> (cisco 1921)----->LAN
Error that I'm retrieving is always the same: Error 789: "The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer"
But I'm able to establish l2tp/ipsec vpn connection to the same vpn server with my iPhone 4.
Below is isakmp debug log from lns router(cisco 1921) when I've tried to establish vpn with windows client. Anything useful from these logs to point me on the right direction to finally solve this problem with windows clients.
#debug crypto isakmp *Apr 8 10:56:47.018: ISAKMP (0): received packet from 186.51.43.137 dport 500 sport 987 Global (N) NEW SA *Apr 8 10:56:47.018: ISAKMP: Created a peer struct for 186.51.43.137, peer port 987 *Apr 8 10:56:47.018: ISAKMP: New peer created peer = 0x3296C24C peer_handle = 0x80000068 [Code]...
We have ASA 5520 running 8.2(3) software and we're trying to make Remote Access VPN (l2tp/ipsec) working from Android. We succeeded in making IPSEC tunnel (ending "Phase 2 completed"), but we cannot make L2TP tunnel working.We're using RADIUS for L2TP authentication, but ASA doesn't even try to check credentials entered by use. The same set of credentials entered on Windows {XP, VISTA, 7, Mobile} works ok. Which debugging options should we turned on?
Is it possible to configure Layer 2 Tunneling Protocol (L2TP) over IPsec on a cisco router like 1921 ISR? This link shows basically what i want to achieve but instead of an ASA, i would like to use just a router with sec..
I have configure L2TP vpn using ASDM and now i am not able to connect my Cisco ASA 5505. it's showing error message 3Jul 07 201118:57:38IP = *.*.*.*, Error processing payload: Payload ID: 1
I’m configuring a L2TP IPSEC VPN on a 5505 asa so that windows 7 clients can natively connect. It connects correctly during Phase 1 and 2, but I can’t ping anything or access resources on the internal network. This is my first time working with an ASA.
Master# sh run : Saved : ASA Version 8.2(2) ! hostname Master domain-name service.local
We have an ASA 5540 successfully using SSL VPN Client Tunnels with no issues, and have been attempting to build the ability for IPSec Clients to connect as well. I have the authentication working, yet cannot complete the establishment of the tunnel for the client. The client receives an error of "Secure VPn Connection terminated by Peer, Reason 433: (Reason not specified by Peer)". In the log on the client, I see the following when the connection drops:
(this is after successful connection, split tunnel setups, then this set of items appears in the log) 377 09:29:08.071 02/28/13 Sev=Info/4 IKE/0x63000014 RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from <outside IP of ASA> 378 09:29:08.071 02/28/13 Sev=Info/5 IKE/0x63000045 RESPONDER-LIFETIME notify has value of 86400 seconds
[code]...
I see the message where it terminates and where is says 'Account Start Failure' but I can't figure out what that is indicating..
I try to connect to RV220W with windows 7 client but I fail : error 789. I compare again and again pre shared key, but it doesn't change anything. How to connect to RV220W with IPsec client ?
i have started managing a asa 5510 firewall which is already having 10 ipsec tunnels , the problem i am facing is they are configured as "ipsec vpn map"
i have attached sample config, i am finding it difficult to understand the parameters used in each tunnel as the configration seems bit complex to me, how it works .
We're in the process of setting up an ASA 5510 as our main VPN appliance.
The Outside interface of the 5510 faces our DMZ, the Inside interface sits on our main network. The 5510 uses radius for authentication going to a server on the same subnet for the authentication. That works fine. VPN client can connect to the 5510 and successfully authenticate. Routes are pass through to the VPN client, no problem. PC with VPN client can access internet (which is by design, it should use it's own internet connection), but cannot ping/access/trace over the tunnel at all.
My hunch is that this is a nat issue - but I am confused as to how the NAT should be configured - I've tried several configurations with no luck.
The VPN client is set to pull an ip address from the pool - 192.168.56.10 - 100. The 5510 is sitting on a separate subnet (50.x/22). This seems to work on the Cisco 1700 that it will be replacing just fine. I mirrored routes and ACLs as well onto the new 5510. No luck. Client connects, authenticates, pulls an IP address and routes, but can't see anything on the inside of the 5510.
I have an ASA 5510 running 8.4(2) which has a site to site IPSec VPN to a 3rd party who run some form of Checkpoint. The VPN establishes and allows access to a server in our DMZ on all ports that we have tested (so far HTTP, SSL, RDP, FTP) except for SQL which doesn't even seem to reach the server. I've got Wireshark running on the DMZ server and if the 3rd party initiates a TCP conversation from their server on any of the working ports to the server I see all of the expected packets arrive with the correct IPs etc (no NAT takes place across the VPN) but when an ODBC client attempts to query the SQL server on our DMZ box the packets do not arrive at the server. What I can see is the RX byte count on the VPN increasing each time the query is run but definitely no SQL arriving at the server.
Also if I revert the ASA back to the old PIX it has replaced with the same VPN config but on version 7.x then it works just fine.
I have been given the following details by a company for us to connec to their IPsec VPN.
IP Address 200.9.21.214 VPN Device Description Cisco ASA VPN Device Version 5510 Encryption Domain 10.152.24.10 Authentication Method Pre Shared Key Encryption Scheme IKE
[code]....
I was going to use VPNC with linux but the company said they do not use remote access. So I tried a draytek vigor 3300v, that as well did not work. Had very bad logging so i couldn't troubleshoot.In the end I have decided to buy the cheapest cisco device that will allow me to connect to this.
I have an ASA 5510 running ver 8.0(2) that has (4) Ipsec tunnels going from it to various other locations. I am having an issue with data transfer speed on only one of the Tunnels. This tunnel is between the 5510 and the 5555, on that link I am getting a dat transfer rate of a little over 120k a second, whereas if I pull the same set of files from another location I am seeing a transfer rate of 5m per second.
I have verified that it is not a capacity issue on the Internet bandwidth on both locations, and I can pull the same data from the same location to various other locations via Ipsec tunnels, I am only having an issue with a specific tunnel going from the 5510 to the 5555.
Since it is not affecting other tunnels on the 5510 nor is it affecting tunnels on the 5555 going to other locations, I am leaning toward a routing issue within the ISP? I will say the ISP is taking me a long way around to stay in the same Metropolitan area.
i've an Cisco ASA 5510 with Security Appliance Software Version 8.0(2), in this ASA i've many L2L tunnels to this ASA, anda sometims new tunnels can't connect, the older tunnels still ok and working, yesterday this situation occured again and i've tried to clear all ipsec tunnels and try to reconnect again no one cames up again. At the time of this situation memory usage was about 78% and CPU is was around 5%. I've made a reload without changes and the situation returns to the normality.
At the time of the fail i've collect the outpu from debug crypto isakmp 255, the outpu was in the annexed file.
