Successfull in setting up an L2TP/IPsec tunnel through NAT-T against a Windows 2008/ R2 RRAS server? I am using an 881 router and the layout is someting like this:Client -> 881 -> NAT -> internet -> Windows 2008 RRAS.The tunnel goes form the 881 to the Windows server (not from the client...).
View 4 RepliesWe have ASA 5520 running 8.2(3) software and we're trying to make Remote Access VPN (l2tp/ipsec) working from Android. We succeeded in making IPSEC tunnel (ending "Phase 2 completed"), but we cannot make L2TP tunnel working.We're using RADIUS for L2TP authentication, but ASA doesn't even try to check credentials entered by use. The same set of credentials entered on Windows {XP, VISTA, 7, Mobile} works ok. Which debugging options should we turned on?
View 3 Replies View Relatedhow to create ip sec tunnel using these parameters. customer ip where tunnel has to be connected 1.1.1.1
ISAKMP Parameters: (Phase I)
Encryption: AES-256 or 3DES
Authentication Mode: Pre-shared key
[Code]......
I'm currently setting up two VPN 3000 Concentrators at two different sites to create a IPsec LAN-to-LAN Tunnel. I have gone through all the basic configuration guides on the CISCO site, but a LAN-to-LAN session is never created. I have enabled the logs on the Concentrator and it displays no errors at all - it appears the Concentrator is not even trying to establish a IPsec LAN-to-LAN Tunnel.After running through the standard setup provided by CISCO, is there anything I need to do to make the Concentrator try to create a Tunnel, or should this be automatic once all settings are in place?
View 2 Replies View Relatedwhat license do I need to create a IPSEC tunnel? I have an ASR 1001, running? [code]
View 2 Replies View RelatedI have a request from my customer asking to provide a model of cisco router that can support 100k or 50k L2TP tunnel session. I have searching around the cisco website but cannot find the right answer.
View 1 Replies View RelatedI'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies View RelatedI'm trying to setup a L2TP over IPSEC vpn connection on a PIX 501 that will use key sharing. In addition, I have a PPTP connection setup which allows connectivity. Two things, the L2TP vpn client I am using does not connect and times out. The second is that the PPTP client I use does connect, but cannot ping any resources on the network.
The config on the PIX is below:
Building configuration...
: Saved
:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password tdkuTUSh53d2MT6B encrypted
[ Code] .....
I am trying to get a L2TP/IPSEC VPN going on one of my servers behind the DIR655 router I have used Port Forwarding and Virtual Server and neithere seem to allow these ports to be open in either situation a port scan shows the ports closed..My ISP (Comcast) does not block these ports?
View 14 Replies View RelatedI had my PPTP VPN working great at my old place, now that I moved I also upgraded my speed which means I got a different 2Wire. This 2Wire can only do DMZ mode and can't bridge. ( I tried everything, including the mdc page, no go). This works fine apart from blocking GRE somehow. I'm using a Mikrotik RB450G as my PPTP server. Does L2TP or IPSEC use the GRE protocol?
View 1 Replies View RelatedI have a stable l2tp/ipsec config that I have been using for many years with the Windows XP native VPN client and the iPhone VPN client.This configuration does not seem to work with the native Windows 7 VPN client. What has changed between XP and 7 on the native VPN client front? I'm running IOS 12.4(15)T5.
View 1 Replies View RelatedI have a Cisco 7200 and need to establish L2TP over IPSEC session with a Draytek Fly200. Draytek must use L2TP over IPSEC to provide LAN-to-LAN connectivity. IPSEC phase 1 and 2 is ok, L2TP tunnel is also established, but on cloned virtual-access IPCP negotiation is not completed:
*Sep 16 09:50:36.911: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state to up
L2X_ADJ: Vi3:midchain adj reqd for ip 0.0.0.0, cid 0
*Sep 16 09:50:38.911: Vi3 IPCP: O CONFREQ [REQsent] id 2 len 10
*Sep 16 09:50:38.911: Vi3 IPCP: Address 192.168.176.2 (0x0306C0A8B002)
*Sep 16 09:50:38.911: Vi3 IPCP: Event[Timeout+] State[REQsent to REQsent]
I think my VPDN configuration from Cisco side is not correct, but I cannot find configuration examples for this kind of solution.
I have a 5510 that i have configured for L2TP over IPSEC, not using AnyConnect. The first, and most prevelant being, VPN clients are unable to ping/access any of the hosts that are assigned a static NAT from the inside interface to the outside interface. I was able to circumvent this by adding another static NAT to the public interface for the incoming clients, but this caused intermittent connectivity issues with inside hosts. The second issue involves DNS. I have configured two DNS servers, both of which reside on the internal network and are in the split_tunnel ACL for VPN clients, but no clients are using this DNS. What is the workaround for using split tunneling AND internal DNS servers, if any?
i've had two different CCNA's look at this numerous times to no avail. A ping from a VPN client to any internal host works fine, unless it is one that is NAT'd. You can see in the config where i added the extra STATIC NAT to try and fix the issue. And this works perfectly across the tunnel but only intermittenly from the internal 10.1.4.x network. [code]
Co-worker just got a Blackberry Playbook tablet and, try as I might, we cannot get the darn thing to successfully set up a working IPSEC/L2TP vpn tunnel to our ASA 5510, which acts as a multi-purpose VPN concentrator. Any luck setting up L2TP/IPSEC VPN to ASA from Blackberry Playbook?
View 0 Replies View RelatedI'm opening a new topic related to my problem with the VPN connection, to avoid confusion, since there are many, in the old information, no longer required.
I would like to configure my ASA5510 L2PT/IpSec to accept connections from Windows clients. I happen to authenticate via AD credentials. When I try to connect is because the error 691. I enabled debugging on the machine the following:
debug crypto isakmp 3
debug crypto ipsec 3
debug ldap 255
i have configure l2tp/ipsec vpn on cisco ASA 5520 and also configure windows 7 client but its getting error
Error in ASA debug log
debug crypto isakmp 7
Mar 26 07:44:28 [IKEv1]: IP = 59.161.130.13, IKE_DECODE RECEIVED Message
[Code]......
i am now trying to configure a Cisco Small Business Pro SRP 521w router for a branch office, i am trying to get the router to connect to a L2TP VPN server inside my datacenter, but seems to me like L2TP VPN client function is not supported inside the SRP 521w router.
Can Cisco implement L2TP VPN client into the firmware for the SRP 521w router in the future ?
i configurated ipsec vpn at cisco asa 5510. all them are working very well. now i want to change ipsec remote vpn to L2tp over ipsec.i have router, asa and 3750 switch. all nat translation are done at router , ipsec vpn configurate at asa.
this is my ipsec configuration. this is working config. as you see i do static nat asa outside ip for vpn at router. now i want l2tp over ipsec. before i do it i have some question
1. must i do static nat port udp 1701 for l2tp over ipsec vpn? can i write access list at asa to open port 1701?
2. can i remove this static nat or i can not be change anything.is this nat is true for l2tp over ipsec vpn?
3.as you see user authentication from radius server at ipsec vpn. i also want this is same as l2tp over ipsec vpn..
4. i think that i must be add this addtional config. is this true? tunnel-group DefaultRAGroup ppp-attributesno authentication chapauthentication ms-chap-v2
is this config enougth for l2tp over ipsec vpn?? what is addtional config i need?
Any good vpn config for a router to allow vpn connections from Android phones using L2TP-IPSEC? Router is an 1841 running most current IOS ver 15.1.
View 1 Replies View RelatedI'm having problem establish l2tp/ipsec vpn connection from Windows vista/7 vpn client to cisco 1921 ( ios 15.2 )
C1 --------> (internet cloud) ---------> (cisco 1921)----->LAN
Error that I'm retrieving is always the same: Error 789: "The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer"
But I'm able to establish l2tp/ipsec vpn connection to the same vpn server with my iPhone 4.
Below is isakmp debug log from lns router(cisco 1921) when I've tried to establish vpn with windows client. Anything useful from these logs to point me on the right direction to finally solve this problem with windows clients.
#debug crypto isakmp
*Apr 8 10:56:47.018: ISAKMP (0): received packet from 186.51.43.137 dport 500 sport 987 Global (N) NEW SA
*Apr 8 10:56:47.018: ISAKMP: Created a peer struct for 186.51.43.137, peer port 987
*Apr 8 10:56:47.018: ISAKMP: New peer created peer = 0x3296C24C peer_handle = 0x80000068
[Code]...
I woulke like to know is it possible to create a VTI tunnel from my 877 router to my ASA, rather than creating a cryptomap on the router ?
View 1 Replies View Relatedwe have two routers CISCO881-K9 and we have established l2tpv3 pesuduwire between two routers: attached the configuration file for both routers.
Although the l2tp established but we are unable to pass the DHCP or other traffic through l2tp tunnel from router A to router- B. [code]
I have a Cisco ASA 5505 Firewall. I am using windows VPN. I have configure IPSEC/L2TP Vpn. And now i hv some problem..
1) VPN is connected but I notices that VPN client connection gets in "HANG" mode after couple of minutes.
2) I am getting error when i try to connect my SQL Server (windows 2008) [code]
Is it possible to configure Layer 2 Tunneling Protocol (L2TP) over IPsec on a cisco router like 1921 ISR? This link shows basically what i want to achieve but instead of an ASA, i would like to use just a router with sec..
[URL]
I'm trying to setup a L2TP VPN Connection on my ASA 5510 to connect with Android/Windows (Native Clients).I'm using the newest Releases:Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.3(5)
My asa config just the interesting part:
crypto ipsec transform-set trans esp-3des esp-sha-hmac crypto ipsec transform-set trans mode transportcrypto ipsec security-association lifetime seconds 28800crypto ipsec security-association lifetime kilobytes 4608000crypto dynamic-map dyno 10 set transform-set transcrypto map vpn 20 ipsec-isakmp dynamic dynocrypto map vpn interface outsidecrypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400no crypto isakmp nat-traversal
[code]....
If i try to connect with a Windows 7 Client (NOT behind NAT) I get the Error 691.
I see that Phase 1/2 are working with debug:
Dec 22 16:32:16 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 1 COMPLETED
Dec 22 16:51:25 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 2 COMPLETED (msgid=00000001)
Then I see this "Error":
Dec 22 16:51:26 [IKEv1]: Group = DefaultRAGroup, IP = XXXXX, Session is being torn down. Reason: L2TP initiated
I don't understand why it doens't work....I tried many templates from the net but nothings works.
I need support regarding IPSEC - VPN in 1841 Router? I had purchsed 1841 Router and i dont know how to check, whether supported for VPN or not?
View 4 Replies View RelatedI have added an ASA 5510 to my network between the Internet and a Windows 2008R2 server running ForeFront TMG. Before the ASA was added, vpn clients using Microsoft Windows 7 vpn client using L2TP/IPsec connected to our vpn. After ASA was added, clients can no longer connect. I would like to know how to configure the ASA to forward the vpn requests to the ForeFront TMG server for authentication and access to internal network resources. Mail is forwarded appropriately through the ASA to internal mail server and Internet access for LAN users works just fine.
Topology:
ASA 5510 (outside interface is ISP IP address, inside interface is 192.168.1.1)................Forefront TMG (outside nic 192.168.1.2, inside nic is LAN gateway IP address).
I have altered the registry key of the client vpn pc's per Microsoft Technet URL
I am getting the following errow message while trying to create a VPN tunnel between an ASA5520 and a 2921 router. [code]
View 9 Replies View RelatedWe are using SRP527 routers with PPPoE ADSL connections. From the SRP527 we create an IPSec tunnel to our core routers (Cisco ASR). We are wanting to change the IPSec tunnels to L2TP, and I need to know if this can be done from the SRP527. I cannot find any L2TP configuration options in the setup options.Can the SRP527W act as an L2TP tunnel initiator over the ADSL PPPoE interface?
View 1 Replies View RelatedI’m configuring a L2TP IPSEC VPN on a 5505 asa so that windows 7 clients can natively connect. It connects correctly during Phase 1 and 2, but I can’t ping anything or access resources on the internal network. This is my first time working with an ASA.
Master# sh run
: Saved
:
ASA Version 8.2(2)
!
hostname Master
domain-name service.local
[code]....
I am trying to create a VPN tunnel between two RVS4000 Routers through a WAN. I get the following error when trying to do so.
"remote Security Group" and "Local Security Group" can't be in the same network.
I need to create multiple ip-sec vpn tunnels on A Cisco 837 ADSL Router. I am able to create one tunnel but the second connection is asking for the outside interface which is atm and already taken by the first tunnel. How can i create more tunnels?
Secondly, after creating the first tunnel i am able to access the remote lan network but when i tried tracert "remote lan ip of a pc" from my pc i got "request timed out" after passing my 837 but succeeded to reach the target. Does tracert needs something to be opened in the router?
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....