I'm trying to set up Windows Server UAG for Direct Access in a Testlab. The UAG Server has two network nics. One in my Testdomain (internal) and the other one in a DMZ of our Cisco ASA (external).Our ASA dmz has subnet 192.168.3.x but UAG Direct Access needs public ip adresses.Is there documentation how to configure an ASA 5520 Firewall so i can use my Windows UAG Server with Direct Access?
View 7 RepliesWe have ASA 5550, I have a portal server in the dmz which is natted statically to a public ip address for port 443. The application works fine from outside world. The server is also nated with a dynamic nat from inside to dmz and when I hit on the dmz ip from my inside it works fine.
The requirement for us is that the users sitting behind the inside (i.e. LAN) should access the server on the public ip address and not thru the dmz.
we have a L2L-VPN-Tunnel beetween our Headquarter (ASA5520 with Network 10.100.1.0) and a branch office (Cisco1841 with network 10.100.10.0 ). This works fine for years, but now we wish to change the configuration so that ALL traffic from the branch office goes over the vpn-tunnel. My question: How I have to change the crypto acl to reach this. Below the relevant parts of the branch route.
View 6 Replies View RelatedWe have a Cisco ASA 5520
We are attempting to setup RRAS on Windows 2008R2 using L2TP. Server is on the inside of the network at 10.10.10.20 our ASA is 10.10.10.1 its outside interface is 68.0.0.0.3/28.
I set a static NAT rule to allow all traffic pointed at 68.0.0.4 to be directed to 10.10.10.20 and have ACLs allowing the following.
esp, ah, udp/500, udp/4500, udp/1701
Mac Clients have no issues with but windows clients seem to hang and never connect. I know the ASA configuration is somehow to blame, if I attempt to connect to LAN IP (10.10.10.20) from withn the same network every thing works fine (making sure all the Windows Issues are covered).We have 2 other IPSEC tunnels established to teh ASA from our COLO and a Satalite office, not sure if this makes it any harder.
I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms.
I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms.I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN).
Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't work.I tested it in the safe mode with networking, same problem there.
It slows down our client-server based programs, what's causing it. All I could google up was that disabling Interrupt Moderation would work, it didn't though.Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.
I have an ASA 5520 in my company which does all our NAT and Firewall access control. Currently there is a rule in place to allow an incoming connection on port 2222 from a specific ip address to allow access to a web app our developers created. This is a test before the web app is released live. Now the web app can communicate with the specific address and port but the incoming connection on port 2222 isn't getting through. Everything looks great in the firewall but how can I log any hits this ACL takes to identify any potential problems?
View 2 Replies View RelatedWith an ASA 5505, i would l like to guide a sub network to an ISP and another sub network to the other ISP.i have 2 differents ISP.My major problem is the metric. I tried with access-list command to force the way out, but it seems that "metric" is stronger than "access-list".I don't know how to manage such LAB. is that possible with ASA 5505 appliance?
View 9 Replies View RelatedI am using ASA5520 with webvpn for file sharing. But recently we just upgraded the OS that accommodate file shared folder from win2003 R2 32bit to windows server 2008 R2 64bit. Now I have a problem with accessing file share by ASA webvpn, it appears error contacting host, we have tested the file shared of webvpn on the other OS windows 2003 and windows 2008, they are working on these OS except win2008 R2. Current the ASA OS version is 8.0(2). And the windows firewall has been disabed.
View 3 Replies View RelatedI have this that comes up when i go on the networking
View 2 Replies View RelatedHow can I access my webserver (on my private LAN) from the internet? INTERNET------------(53.X.X.1 )ASA(192.X.X.X)DMZ-----------(192.X.X.80)HTTP SERVER. I can ping my public address on the ASA outside interface 53.X.X.1 form the internet, but I'm not sure how to do this. I tried to NAT, but I'm failing.
View 3 Replies View RelatedI have a cisco asa 5520 ios 8.2. This is my configuration [code] But i can not access from DMZ to INSIDE.
View 3 Replies View RelatedI just configure an ASA 5520, here is the config (the ip address of outside network if going to change from private direccion by reason security).
The problem that I have is the users can access to the web site through the public´s ip address but they do not can access through by name. We review all the config on the server DNS and with the command NSLOOKUP we can see that work fine. The client think that the asa is blocked the connnection.
[code]....
A bit of a straight forward question, is it possible to connect a 5505 to a 5510 direct via a crossover or do you need a switch inbetween capable of trunking?
View 1 Replies View RelatedI have the following scenario.
INET
(205.50.50.1)
|
|
(205.50.50.2)
[CISCO ASA 5540]
(10.10.10.1)
|
|
+ ---------------------------------------------+
(10.10.10.2) (10.10.10.3)
[BARRACUDA] [Exchange SRV]
Mail Domain: mail.domain.com (205.50.50.50)
Ok so the mail flows to the Barracuda using a static 1:1 NAT configuration and then gets delivered from the Barracuda to the Exchange server. I want to implement active sync (Direct Push) for Windows mobile devices. They need to communicate with mail.domain.com over port 443. The problem is I want mail to continue to flow to the Barracuda, but direct Direct Push traffic to the Exchange server.I cnow I can't implement two 1:1 NAT mappings from the same external hostname to 2 different servers.
I've just got my DCS-2121 up and working. But i can't figureout how to access the direct URL for the camera?And is there a URL for still images aswell?I got an iPad and an iPhone, but i can't access the camera because it use Java.I had another DCS-900 where i could access IMAGE.jpg and Video.cgi. Is there anything like those for the DCS-2121?
View 7 Replies View RelatedWe have an ASA 5520 in HA. (version 8.X upgraded to 9.1 (1))We used Wizzard to configure VPN clientless and portal. Also, configured manually we have the same issue: We can access to the portal using IP address of Lan interface but not with outsides (2 ISP). The clientless VPN is enable on the public interface and no packets rejected in logs.We try to modify the Crypto map created by default to replace "any" to "any" by "any" to "our public IP" (We see that is recommended by Cisco) It works for 10 minutes.(strange..) but after 10 minutes the active member crashs.. only a reboot with previous configuration was good.We try to investigate but each time we modify Crypto maps, the firewall is going bad.
View 7 Replies View RelatedI have been configuring a cisco ASA 5520, everything is working fine but when i create an ACL:
-access-list OUT extended permit ip 172.16.x.x 255.255.255.0 any
-access-group OUT out interface outside
i added ports like www or 443 and it is not working to Internet access a router is before to my firewall connected to my headquater, i can see my private networks but i cannot able to reach Internet access,
We are moving from a different vendor to ASA 5520s. So far my "training" for Cisco consists of s Cisco press book, some white papers and guides, this website, and a bunch of mistakes. So, I have what is probably a pretty basic question for most folks.
What is the difference between Firewall Access Rules and ACL/ACE? And when to use which?
for example: on my ASA 5520s I've set up an Interface for my internal LAN: 172.16.x.x., a DMZ 192.168.2.0/24, and an interface for the Internet side. The 5520 is set up as a routing firewall betwen my internal lan, DMZ, and Internet.
If I want to allow my internal users Internet access for http and https would I use a Firewall Access rule?For most of my rules allowing outbound access from my 172 LAN and DMZ and inbound access to devices in my DMZ can I mostly utilize the Firewall Access Rules?
I have successfully been able to allow outbound access from inbound hosts on the appliance; however, I have only one outbound IP address and had to configure outbound access using static PAT. What I need to do is to configure access to certain inbound hosts from outside. What's wrong with my running config? Below are the commands that I believe need to be changed from the configuration. [code]
View 14 Replies View RelatedI've got what is probably a very basic question - but i can't figure it out.I have: Internet (ADSL) -> 2851 (ADSL wic) -> 5520 -> internal LAN (192.168.1.x/24)
The asa has just replaced a Checkpoint firewall.I've set up the ASA to the point where all hosts on the internal LAN have internet access (using a dynamic PAT on that network). This all works well.
The problem i have is i am trying to allow access from the internet to an internal host on a specifc TCP port (as i had done on the Checkpoint) but i'm getting:
Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:111.111.111.11/52135 dst inside:192.168.1.252/5555 denied due to NAT reverse path failure
From what i have read i need to add a NAT exemption for this particular use case - to avoid the dynamic NAT i have setup, but im not sure how to do so.I'm running 9.1 on the ASA, no VPNs yet. Just this basic setup.
I am new in ASA, I have the DMZ (10.1.1.0/24) configured on ASA 5520 and I achieve the reach Internet from DMZ (10.1.1.0/24), but now need reach DMZ from inside (172.16.12.0/24) and inside (172.16.12.0/24) from DMZ (10.1.1.0/24), in other words round trip.
View 6 Replies View RelatedI have a site to site VPN between SiteA to SiteB which is working fine. SiteA has an ASA5520 and SiteB Pix501. The ASA5520 is running version 804 with split tunneling. Users connect to SiteA using remote access VPN. Is it possible to setup SiteA ASA5520 so that when users connect to SiteA they can access servers located on SiteB through the tunnel? I know i can setup the Pix501 for remote access VPN but it is located in another country and i don't want to take a chance just incase i lose connectivity.
View 7 Replies View RelatedI have a RV042 Dual WAN router. What I would like to be able to do is to direct a computer on my network to access one particular WAN. For example, WAN1 is a DSL line and WAN2 is a cable line. I would like to direct a computer on our LAN to access the cable line always, even though I have Smart Link Backup set to WAN1. Is this possible?
View 6 Replies View RelatedCurrently, my customer has 2 units of Cisco PIX 515E running on Active/Standby mode. As for the heartbeat link, there are 2 dedicated switches placed in between both the Cisco PIX 515E i.e. FW1 --> SW1 --> SW2 --> FW2.
My customer will be changing both the Cisco PIX 515E to Cisco ASA 5510. Now, they are asking me, since they will be using Cisco ASA 5510 eventually, can the heartbeat link be a direct UTP cross cable or must the 2 switches in between still exist?
I remember I have tested this before, few years back, in the event I were to pull out the UTP cross cable that's connecting both the Cisco ASA 5510 Firewalls directly (without any switches in between), the Active/Standby mode still works fine. It doesn't go bad whereby both the Cisco ASA 5510 suddenly becomes Active/Active, and causes network issue.
Are switches required for the heartbeat link in a Cisco ASA environment or can a direct UTP cross cable connection be adequate.
Our company has recently upgraded our firewall from a Borderware Steelgate v7.1 platform to a Cisco ASA 5520 platform. Needless to say the interface on the Cisco platform is much more complex and I don't have much experience working with firewalls. Our other IT guy is out of town and this is the first time I have worked on this setup.
I need to create the following access rule
I need to open port 4**0 to be allowed through the firewall from external ip address 10.XXX.XX.XXX only. Then forward port 4**0 to 10.XX.XX.XX port 80 tcp
I am using ASA 5520 with 8.2.4 IOS. I'm new to ASA/Firewall. I need to do access webserver from outside network.From Laptop (192.168.2.51), If I connect to url... it should open page from 10.10.10.50.I also need to ssh to webserver from laptop. If I ssh to 192.168.2.50 from laptop, it should connect to 10. 10. 10.50. [code]I can't get to webserver from outside network, so now, I connected laptop to directly ASA 5520 outside port with crossover cable.ASA Inside port connects to L3 switch. Webserver also connects to L3 switch. But still doesn't work.
View 9 Replies View RelatedAfter upgrading to 8.4(2) and ASDM 6.4(5) I seem to have an extra access rule duplicating an existing rule, this is only visable through the ASDM. When using the CLI you can't see this duplicate rule.
I therfore get the following warning everytime I make a config change using the ASDM [code] If I delete this rule it returns everytime I launch the ASDM!
I also have extra config under Firewall>Configuration>Public Servers that I didn't have before. If I delete it, again it returns.
i have cisco ASA5520 and i have a remote access vpn .I want to configure logging for this remote access vpn.
i want the time user connected .how log it is connected .If any error while connecting ?
When trying to access the asa (8.0(3)) with asdm the console send follwing error message:
vPif_isVpifNumValid: pifNum out of range!
vPif_getVpif: bad vPifNum(0xa6) from 87EBC81 from 83833B4
Have a strong suspicion that it is a hardware failure (since asdm has worked and have tried to restart the box) can not see any errors with any show commands, but could it be a RAM error .
This is just a general question... is there a good way to organize the ASA's access rule list to increase its efficiency? Maybe by service or hit count (Top 10). I am using the Cisco ASDM 6.2 to manage our ASA 5520.
Looking at it looks very unappealing and I'm in the process of adding names and descriptions to all the Network Objects.
We have a Cisco ASA 5520 and Web sense. I added a filter but it seems like it is still not allowing us to access a certain website from most of the machines however some machines with the same configuration work on the DMZ. Accessing website tells us:
"Firefox has detected that the server is redirecting the request for this address in a way that will never complete".
Filter I applied on the firewall:
filter url except 0.0.0.0 0.0.0.0 64.18.218.0 255.255.255.0 allow
filter https except 0.0.0.0 0.0.0.0 64.18.218.0 255.255.255.0 allow
I have an ASA 5520 with a DMZ with private addresses that I SNAT to my outside network. From inside the DMZ I can reach servers by both the internal private IP and the public IP, except if the IP is from the server trying to connect. So, say I have server1 and server2. I can connect from server1 to server 2 with both public and private, but can't connect from server1 to server1' using the public IP. ASA logs show that packets are being denied due to land attack. DNS doctoring is not an option for me.
View 1 Replies View RelatedHave cisco ASA5520 on place and i want to configure it to access my webserver outside of my network throught sftp/ftp with filezila what command to add so as port/service associate to it should be able to run?
View 1 Replies View Related