I have successfully been able to allow outbound access from inbound hosts on the appliance; however, I have only one outbound IP address and had to configure outbound access using static PAT. What I need to do is to configure access to certain inbound hosts from outside. What's wrong with my running config? Below are the commands that I believe need to be changed from the configuration. [code]
View 14 Replies
I have a client that has an ASA 5520 that has two internet connections, FIOS and Comcast. The ASA is configured to failover from the FIOS to the Comcast if the FIOS fails. This works perfectly fine. However, I was wondering if VPN and other inbound traffic will come into the secondary connection when it is active. I think VPN will work inbound when the FIOS connection fails, but I am not sure about the other inbound connections.
View 1 Replies View RelatedI am configuring new ASA 5520 with AIP module for our network with HA (2 boxes), would be the best practice to configure in order to protect web servers and email server.
View 2 Replies View RelatedI present wish to develop a policy and template for QOS on our ASA 5520 release 8.0(2) we presently have wish to do server hosting in our network for other organization,which the they will be able to access their servers they have both public and private addresses. we do have our one servers also already in production all behind the ASA And therefore we wish to apply qos on the servers to be hosted and we wish to do this on the ASA. how to go about this to apply qos on the ASA?
View 3 Replies View RelatedTo configure a dynamic NAT, PAT, or identity NAT rule, I need to perform the following steps:
Step 1 From the Configuration > Firewall > NAT Rules pane, choose Add > Add Dynamic NAT Rule.
The Add Dynamic NAT Rule dialog box appears. However, when I click on Add I don't get the option to Add Dynamic Nat Rule. To see the options I get please see attachment.
The following is a capture of the show version:
ciscoasa# show ver Cisco Adaptive Security Appliance Software Version 8.4(2) <system> Device Manager Version 6.4(1) Compiled on Wed 15-Jun-11 18:17 by builders System image file is "Unknown, monitor mode tftp booted image" Config file at boot was "start up-config"
ciscoasa up 16 mins 57 secs Hardware: ASA 5520, 1024 MB RAM, CPU Pentium II 1000 MHz Internal ATA Compact Flash, 256MB
BIOS Flash unknown @ 0x0, 0KB
0: Ext: GigabitEthernet0 : address is 00ab.a72f.0100, irq 0
1: Ext: GigabitEthernet1 : address is 00ab.a72f.0101, irq 0
2: Ext: GigabitEthernet2 : address is 0000.ab6d.9802, irq 0
[code]...
This platform has an ASA 5520 VPN Plus license. Serial Number: 123456789AB
Running Permanent Activation Key: 0x4a3ec071 0x0d86fbf6 0x7cb1bc48 0x8b48b8b0 0xf317c0b5
Configuration register is 0x0
Configuration has not been modified since last system restart.
I'm running a Cisco ASA 5510 with version 7.2(3) and I've been tasked with permitting some inbound & outbound TCP & UDP ports to/from a specified address space on the internet.
In looking at my current ASA config I see other access lists already configured so I'm assuming I can just set up a new access list in similar fashion, but I wanted to verify here first.
I configure the virtual MAC address for a interface on ASA 5520, will enter the following command on the active unit:
failover mac address Inside 0012.3456.789a 0023.4567.89ab
The active MAC address is of the same as the Inside's burned-in MAC address of the active unit.Similarly, the standby MAC address is of the same as the Inside's burned-in MAC address of the standby unit.Do I get the effect of failover mac address command?
I have two ASA 5520 with 4 Giga interfaces and 1 management interface.
I need to use 4 interfaces four data traffic
1- Inside
2- Outside
3- dmz-1
4- dmz-2
The remaining will be the management interface only.How can I configure the Statefull failover and Management?
1- I used the management0/0 for The stateful failover.
2- I used gig 0 for outside
3- I used gig 1 for inside
4- I used gig 2 for dmz-1
5- I divided the gig 3 to two sub interfaces
a- gig0/3.1 for dmz-2
b- gig0/3.2 for Management and I defined it as a management-only
Trying to allow inbound access from any host outside to my LAN server on port 995. [code]
View 1 Replies View RelatedI am new to Cisco firewalls. We are moving from a different vendor to Cisco ASA 5520s.I have two ASA 5520s running ASA 8.2(5). I am managing them with ASDM 6.4(5).I am trying to setup Active/Standby using the High Availability Wizard. I have interfaces on each device setup with just an IP address and subnet mask. Primary is 10.1.70.1/24 and secondary is 10.1.70.2/24. The interfaces are connected to a switch and these interfaces are the only nodes on this switch. When I run the Wizard on the primary, configure for Active/Standby, enter the peer IP of 10.1.70.2 and I get an error message saying that the peer test failed, followed by an error saying ASDM is temporarily unable to connect to the firewall.
View 5 Replies View RelatedSetup firewall rules that will block all inbound Internet access to the web server except port 443, Setup firewall rules that will block all communication between the two internal networks, except ports 7000 and 1702
View 1 Replies View RelatedI need configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.I have attempted to configure rdp access but it does not seem to be working for me. How to modify my current configuration to allow this? I need to allow the following IP addresses to have RDP access to my server: [code] The other server shows up as 99.89.69.334 but is working fine.
I already added one server for Static route and RDP but when I try to put in same commands it doesnt allow me to for this new one. My configuration file and what are the commands i need in order to put this through. Also, if there are any bad/conflicting entries. Also I have modified IP information so that its not the ACTUAL ip info for my server/network etc... lol for security reasons of course.Also the bolded lines are the modifications I made but that arent working. [code]
I have an ASA 5520 in my company which does all our NAT and Firewall access control. Currently there is a rule in place to allow an incoming connection on port 2222 from a specific ip address to allow access to a web app our developers created. This is a test before the web app is released live. Now the web app can communicate with the specific address and port but the incoming connection on port 2222 isn't getting through. Everything looks great in the firewall but how can I log any hits this ACL takes to identify any potential problems?
View 2 Replies View RelatedHow can I access my webserver (on my private LAN) from the internet? INTERNET------------(53.X.X.1 )ASA(192.X.X.X)DMZ-----------(192.X.X.80)HTTP SERVER. I can ping my public address on the ASA outside interface 53.X.X.1 form the internet, but I'm not sure how to do this. I tried to NAT, but I'm failing.
View 3 Replies View RelatedI have a cisco asa 5520 ios 8.2. This is my configuration [code] But i can not access from DMZ to INSIDE.
View 3 Replies View RelatedI just configure an ASA 5520, here is the config (the ip address of outside network if going to change from private direccion by reason security).
The problem that I have is the users can access to the web site through the public´s ip address but they do not can access through by name. We review all the config on the server DNS and with the command NSLOOKUP we can see that work fine. The client think that the asa is blocked the connnection.
[code]....
We have an IAS (Internet Authentication Server) to authenticate all our network devices. This server is integrated with our local AD server so that we can use our domain credentials to login into the netwoerk devices. i have successfully configured all our L2 & L3 switches with IAS but facing issue with ASA 5520. Below is the config i have applied on ASA. When i am testing the authentication with IAS server, i am getting "Authentication Successful" message.
aaa-server AAA protocol radius
aaa-server AAA host 10.91.38.70
key *****
[Code]....
Also when i am trying to telnet the Firewall, i am directly getting password promt. I should first get the username promt wherein i can enter my domain username.
Trying a simple Easy VPN connection and getting the following in the error logs:
Built inbound UDP connection 684 for outside:xx.xx.xx.xx/1106 (xx.xx.xx.xx/1106) to identity:xx.xx.xx.xx/500 (xx.xx.xx.xx/500)
I am trying to setup an inbound NAT on an ASA5510 running 8.4 code.
object network obj-192.168.1.2
host 192.168.1.2 (internal web server)
object network NAT-external IP
host ** external IP **
object network NAT-external IP
nat (outside,inside) static 192.168.1.2 service tcp https https
access-list outside_access_in extended permit tcp any host 10.2.0.10 eq https
This seems to be setup now?
sh nat
2 (outside) to (inside) source static NAT-*.*.*.* 192.168.1.2 service tcp https https
translate_hits = 0, untranslate_hits = 0
sh access-l
access-list outside_access_in line 2 extended permit tcp any host 192.168.1.2 eq https (hitcnt=27) 0x59383a04
When I try to connect to the external IP using https I get hits on the access list, however the nat translate hits do not go up?Do I need to allow the 192.168.1.2 server back out again?
I'm trying to set up Windows Server UAG for Direct Access in a Testlab. The UAG Server has two network nics. One in my Testdomain (internal) and the other one in a DMZ of our Cisco ASA (external).Our ASA dmz has subnet 192.168.3.x but UAG Direct Access needs public ip adresses.Is there documentation how to configure an ASA 5520 Firewall so i can use my Windows UAG Server with Direct Access?
View 7 Replies View RelatedWe have an ASA 5520 in HA. (version 8.X upgraded to 9.1 (1))We used Wizzard to configure VPN clientless and portal. Also, configured manually we have the same issue: We can access to the portal using IP address of Lan interface but not with outsides (2 ISP). The clientless VPN is enable on the public interface and no packets rejected in logs.We try to modify the Crypto map created by default to replace "any" to "any" by "any" to "our public IP" (We see that is recommended by Cisco) It works for 10 minutes.(strange..) but after 10 minutes the active member crashs.. only a reboot with previous configuration was good.We try to investigate but each time we modify Crypto maps, the firewall is going bad.
View 7 Replies View RelatedI have been configuring a cisco ASA 5520, everything is working fine but when i create an ACL:
-access-list OUT extended permit ip 172.16.x.x 255.255.255.0 any
-access-group OUT out interface outside
i added ports like www or 443 and it is not working to Internet access a router is before to my firewall connected to my headquater, i can see my private networks but i cannot able to reach Internet access,
We are moving from a different vendor to ASA 5520s. So far my "training" for Cisco consists of s Cisco press book, some white papers and guides, this website, and a bunch of mistakes. So, I have what is probably a pretty basic question for most folks.
What is the difference between Firewall Access Rules and ACL/ACE? And when to use which?
for example: on my ASA 5520s I've set up an Interface for my internal LAN: 172.16.x.x., a DMZ 192.168.2.0/24, and an interface for the Internet side. The 5520 is set up as a routing firewall betwen my internal lan, DMZ, and Internet.
If I want to allow my internal users Internet access for http and https would I use a Firewall Access rule?For most of my rules allowing outbound access from my 172 LAN and DMZ and inbound access to devices in my DMZ can I mostly utilize the Firewall Access Rules?
I've got what is probably a very basic question - but i can't figure it out.I have: Internet (ADSL) -> 2851 (ADSL wic) -> 5520 -> internal LAN (192.168.1.x/24)
The asa has just replaced a Checkpoint firewall.I've set up the ASA to the point where all hosts on the internal LAN have internet access (using a dynamic PAT on that network). This all works well.
The problem i have is i am trying to allow access from the internet to an internal host on a specifc TCP port (as i had done on the Checkpoint) but i'm getting:
Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:111.111.111.11/52135 dst inside:192.168.1.252/5555 denied due to NAT reverse path failure
From what i have read i need to add a NAT exemption for this particular use case - to avoid the dynamic NAT i have setup, but im not sure how to do so.I'm running 9.1 on the ASA, no VPNs yet. Just this basic setup.
I am new in ASA, I have the DMZ (10.1.1.0/24) configured on ASA 5520 and I achieve the reach Internet from DMZ (10.1.1.0/24), but now need reach DMZ from inside (172.16.12.0/24) and inside (172.16.12.0/24) from DMZ (10.1.1.0/24), in other words round trip.
View 6 Replies View RelatedI have a site to site VPN between SiteA to SiteB which is working fine. SiteA has an ASA5520 and SiteB Pix501. The ASA5520 is running version 804 with split tunneling. Users connect to SiteA using remote access VPN. Is it possible to setup SiteA ASA5520 so that when users connect to SiteA they can access servers located on SiteB through the tunnel? I know i can setup the Pix501 for remote access VPN but it is located in another country and i don't want to take a chance just incase i lose connectivity.
View 7 Replies View RelatedI have a SSL certificate from a third party that is showing under the Identity in ADSM, howerver the audit scan of the firewall shows that the SSL Certificate Signed with an unknown certification Authority. I have installed the Intermediate Primary and Secondary Certificate from the third party under the CA Certificate of the ADSM however when I verify the SSL certificate it still shows as self-signed. What other steps do I miss. I have attached some screenshots.
View 2 Replies View RelatedI have some troubles configuring split-tunneling on ASA 5520.Number of remote users establish ipsec connection with ASA 5520 (in central office) using ubuntu vpnc-client.Split-tunneling is in use, to allow remote users to surf Internet using their ISP.The goal is to remove the possibility to ssh/telnet servers inside corporate LAN for remote users. [code]
There is nat enabled on interface, but there is special statement in nat0 ACL for 192.168.100.0 subnetwork access-list INSIDE_LAN_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.100.0 255.255.255.0.The problem is that remote users can easely ssh and telnet servers in INSIDE_LAN network. Whatever i put in INSIDE_LAN_in ACL, remote users still have full access to this network. Restrictions in REMOTE_split ACL don't work either.
I am trying to configure my ASA5505 to allow SMTP relay and the ACLStatic I created is not working.
View 1 Replies View RelatedI have setup an ASA5505 running 8.2 with dual ISP's
Primary link is the current live static route out and the backup picks up if the primary fails. That all works great However I have an issue with inbound NAT rules
I have configured an inbound static on the primary which works great
static (inside,primary) *.*.*.* 10.1.1.1 netmask 255.255.255.255 access-list outside_access_in line 2 extended permit tcp any host *.*.*.* eq 3389 (hitcnt=4)
Question? With the primary link active and the default route pointing out through the primary, am I able to configure an inbound NAT to the same inside host 10.1.1.1
on the backup link?
If the primary fails users will need to be able to connect inbound to this service
When I try to set it up I got this error ERROR: Static PAT using the interface requires the use of the 'interface' keyword instead of the interface IP address
So I tried that and got this error WARNING: All traffic destined to the IP address of the backup interface is being redirected. WARNING: Users will not be able to access any service enabled on the backup interface.
So what is the best practice for configuring inbound NAT for a dual ISP configured ASA
I have a 2621 router - old. but works well.Need to put in an ACL to limit the inbound SMTP traffic to be FROM a specific set of IP's, and deny all others.
I have tried various combinations with no luck. Something obvious, I am sure.
When I do a show access lists 160 it shows all SMTP traffic being snagged by the SMTP deny statement. All other traffic works correctly.
Here is my config so far...
Current configuration : 3093 bytes!version 12.2no service single-slot-reload-enableservice timestamps debug uptimeservice timestamps log uptimeno service password-encryption!hostname xxxxxxxxxx!logging rate-limit console 10 except errorsenable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx!ip subnet-
[Code] ....
Our company has recently upgraded our firewall from a Borderware Steelgate v7.1 platform to a Cisco ASA 5520 platform. Needless to say the interface on the Cisco platform is much more complex and I don't have much experience working with firewalls. Our other IT guy is out of town and this is the first time I have worked on this setup.
I need to create the following access rule
I need to open port 4**0 to be allowed through the firewall from external ip address 10.XXX.XX.XXX only. Then forward port 4**0 to 10.XX.XX.XX port 80 tcp
I am using ASA 5520 with 8.2.4 IOS. I'm new to ASA/Firewall. I need to do access webserver from outside network.From Laptop (192.168.2.51), If I connect to url... it should open page from 10.10.10.50.I also need to ssh to webserver from laptop. If I ssh to 192.168.2.50 from laptop, it should connect to 10. 10. 10.50. [code]I can't get to webserver from outside network, so now, I connected laptop to directly ASA 5520 outside port with crossover cable.ASA Inside port connects to L3 switch. Webserver also connects to L3 switch. But still doesn't work.
View 9 Replies View Related
