Cisco VPN :: 5520 - How Much Traffic Pass Through Into IPSec In ASA Firewall

Mar 20, 2013

How can I see the quantity of traffic that is passing through into an IPSec VPN in a ASA 5520.

View 3 Replies


ADVERTISEMENT

Cisco Firewall :: 5520 To Pass Traffic Through Ssm 20 And To Create Sensors

Jun 20, 2011

I have installed asa 5520 , software ver is 8.4,I have SSM-20 installed in asa 5520. How to pass traffic through this ssm-20 ,how to create sensors,how to update signatures of this IPS module ,is there any procedure to automatically update the signatures .

View 1 Replies View Related

Cisco VPN :: ASA 5520 / VPN Phase 2 Complete But LAN Traffic Doesn't Pass

Aug 6, 2011

Just setup a site to site vpn between 2 ASA 5520 Firewalls in two locations but vpn doesn't work even though i see phase 2 completed on the logs. I can't ping across the LANs.

View 2 Replies View Related

Cisco Switching/Routing :: ASA 5520 - Can't Ping / Pass Traffic Through Interfaces

Apr 17, 2012

I've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).

Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.

View 1 Replies View Related

Cisco Firewall :: ASA5505 Does Not Pass Traffic

Jan 25, 2013

I used the GUI configuration tool for this ASA 5505. When I install it no traffic passes. I am wondering to verify my config. I have masked the usernames for VPN with xxxxxx and yyyyyy. [code]

View 6 Replies View Related

Cisco Firewall :: ASA5505 Will Not Pass Traffic?

Nov 15, 2011

I am trying to setup my very first ASA5505 and I cannot get it to pass traffic from the inside to the outside. I am not using NAT/PAT. Here is what I have done so far.
 
ASA5505(config)# interface Vlan 1ASA5505(config-if)# nameif insideASA5505(config-if)# security-level 100ASA5505(config-if)# ip address 33.46.132.34 255.255.255.248ASA5505(config-if)# no shut

[Code]....

Then from the asdm I permited everything from inside to go out but I cannot get any traffic through. I can ping the outside if I source the outside interface but not if I source the inside. The logs would not show me anything.
 
I did a packet tracer and it indicates the implicit deny rule at the end of the access-list is stopping my traffic eventhough I have allow rules above it?
 
I also checked the box in the asdm to allow traffic to pass without NAT

View 5 Replies View Related

Cisco Firewall :: PPTP Traffic Cannot Pass Through PIX 525 7.0(7)

May 6, 2008

i read cisco document:[URL] pptp client is in inside,pptp server is in outside.when i donot use firewall, the pptp connection can establish successfully.but use pix 525 7.0(7) i config:

inspect pptp.
pptp connection cannot setup.
show connection in pix:
pptp tcp 1723 is ok.

gre connection only one "E" flag, E means 'outside back connection'.i try second method:delete 'inspect pptp',permit tcp 1723 and gre traffic from outside to inside, and i have config static nat,but the pptp connection cannot work too.so i think there is a pptp bug exist in pix 7.0(7).

View 5 Replies View Related

Cisco Firewall :: ASA5505 Connects Through Lan But Cannot Pass Traffic

Sep 13, 2011

We have an issue where by we connect to various customers and the Cisco IPSEC remote access works fine from our LAN through an ASA5505 to a customer site.We have 1 customer that we have some issues with. We can connect  from the LAN through to the customers VPN, authenticate and establish a tunnel but in we cannot pass traffic. When we try from outside of the office on a public internet connection the VPN works fine. What could cause this issue?

View 3 Replies View Related

Cisco Firewall :: 5520 L2TP Pass Through To Windows Server

Oct 2, 2012

We have a Cisco ASA 5520
 
We are attempting to setup RRAS on Windows 2008R2 using L2TP. Server is on the inside of the network at 10.10.10.20 our ASA is 10.10.10.1 its outside interface is 68.0.0.0.3/28.
 
I set a static NAT rule to allow all traffic pointed at 68.0.0.4 to be directed to 10.10.10.20 and have ACLs allowing the following.
esp, ah, udp/500, udp/4500, udp/1701
 
Mac Clients have no issues with but windows clients seem to hang and never connect. I know the ASA configuration is somehow to blame, if I attempt to connect to LAN IP (10.10.10.20) from withn the same network every thing works fine (making sure all the Windows Issues are covered).We have 2 other IPSEC tunnels established to teh ASA from our COLO and a Satalite office, not sure if this makes it any harder.

View 2 Replies View Related

Cisco VPN :: ASA 5520 IPSec Overlap - How To Route Traffic

Nov 13, 2011

We have multiple vpn tunnels coming to our cisco asa 5520 , the problem is that when we create another tunnel with the same network as another network on the firewall , it does not know how to route the traffic to which interface or sub interface.

View 2 Replies View Related

Cisco Firewall :: Allowing Multicast Traffic To Pass Through ASA5510

Mar 1, 2011

I ' m not able to configure the asa 5510 to allow the multicast traffic to pass through ASA.The multicast traffic have to pass from inside interface to outside interface.Can I configure the multicast traffic to pass through asa with a static nat ?

View 1 Replies View Related

Cisco Firewall :: Pass Management VLAN Traffic Through ASA 5510 In Transparent

Mar 10, 2013

We have a small cisco 1800 series workgroup router that seperates our network from the outside world.  The data coming into our network goes into the router on interface fa0/1 and comes out on interface fa0/0.  fa0/0 is split into 2 sub-interfaces (fa0/0.2 and 0/0.3).  These sub-interfaces correspond to a desktop and server vlan on our network.  The workgroup router is connected to a 3560G trunk port (we'll call it switch 1) and switch 1 connects to another 3560G (we'll call it switch 2). Recently I was asked to add another layer of security to our network by installing an ASA 5510 firewall and forcing certain types of traffic to authenticate using their domain credentials for our network.  The firewall was set up between the router and switch 1 in transparent, multi-context mode.  There are 2 security contexts, 1 for the desktop vlan and 1 for the server.  Both have the same security settings applied to them since we want the same behavior regardless of whether they are trying to access the servers or the workstations.

View 2 Replies View Related

Cisco Firewall :: 5505 Transparent Mode Doesn't Pass Traffic

Dec 4, 2012

  asa 5505 do not pass traffic as a patch cord, how to make it pass traffic? [code]

View 2 Replies View Related

Cisco Firewall :: ASA 5510 Users Are Unable To Pass Traffic When Connected Through Vpn

Sep 12, 2011

I am migrating over from and old PIX to an ASA 5510. After configuring the new device everything else is functional (Internet) but users are unable to pass traffic when connected through the vpn, they are able to authenticate and I see their session connected on the ASDM but no data is passed..[code]

View 4 Replies View Related

Cisco Firewall :: ASA 5520 - Allow Traffic From DMZ To Internet And Block Traffic?

Apr 29, 2012

I have an ASA 5520 with the below config
 
Gi0/0: outside (Internet)
Gi0/1: inside (Internal users)
Gi0/2: DMZ (web servers, ftp, Mail etc..)
 
I have a SMTP relay deployed on the DMZ for mailing. I have also a mail servers installed in the internal lan,
 
I want to allow trafic from dmz to reach internal lan, and i want normally also allow stmp relay from dmz to reach Internet.
 
How can i block trafic from DMZ to reach Internal Lan (instead of smtp) if the to allow trafic from dmz to internet i must put ANY in the policy?
 
For allowing trafic from DMZ to reach Internet, the policy must be DMZ -----> ANY ----->Services., this policy means DMZ can implicity reach Internal Lan?

View 2 Replies View Related

Cisco Firewall :: Asa 5520 No Ipsec Involved With Office 3

Mar 2, 2013

I have two ASA 5520 units, both running version 8.3(2) code.  Among many other uses, they have an IPSec tunnel between them to link office 1 and office 3 together.  Office 2 does exist, and is connected to a different port on the ASA in office 3; there is no IPSec involved with office 3.

View 6 Replies View Related

Cisco Firewall :: Setup Of IPSec Passthrough On ASA 5520

Mar 28, 2012

I am working on IPSec Passthrough on an ASA 5520, with version 8.3, and ASDM 6.3. Currently I have a requirement for users in my internal network (10.10.249.128 / 25) to be able to connect to external IPSec VPN servers.
 
So I created a network object with 10.10.249.128 / 25, and used dynamic PAT to translate the source ip address to the external internet facing outside interface:

I then added the following rules on the inside-in ACL: However troubleshooting shows that isakmp is passing through the firewall, but esp and ah is not.
 
For isakmp:
 
For ESP:Seems like the nat rule is drawing my ESP traffic,

View 1 Replies View Related

Cisco Firewall :: ASA 5520 - IPSec Tunnel Without Private Network

Apr 11, 2013

I'm trying to achieve a site-to-site ipsec tunnel to a Cisco ASA 5520.  Most examples feature the ASA with a public interface that terminates the tuennel and a private network on another interface that the tunnel interacts with.  Where my scenario differs is that the interface that accepts the tunnel is part of a public /29 network where I want the remaining hosts on that subnet to be able to route thrugh to the other end of the tunnel.  My tunnel gets established, but any attempts to route via the IP assigned to that one interface result in the ASA rejecting traffic. If so, what configuration options should I consider?

View 5 Replies View Related

Cisco Firewall :: Command To Check IPSEC Tunnel On ASA 5520?

Jan 7, 2013

Need to check how many tunnels IPSEC are running over ASA 5520.Tried commands which we use on Routers no luck?

View 6 Replies View Related

Cisco Firewall :: 5520 - Restrict Remote IPSec Vpn From Company Pcs Only?

Aug 19, 2012

we wish to implement IPSec remote access vpn with the condition that employees should be able connect to this vpn only from company issued laptops and not from any other computers. I assume using client side certs is one of the ways to do it but I couldn't find any doc that was really useful. Cisco's documentation seems quite obscure. We are on 8.1 (5520)

View 2 Replies View Related

Cisco Firewall :: ASA 5520 - VPN Traffic Is Getting Dropped Through Firewall

Apr 8, 2011

Our Local Network is behind the CISCO ASA Firewall.Whenever we are accessing to Client VPN server,it is getting connected but after few Minutes (May be 5/10/30 Min),the sessions are terminating. The same traffic through PIX is no issue , only with ASA Firewall. See the following Error and request you give the possible root cause for this.
 
2011-04-09 16:15:09    Local4.Info    172.16.1.68    %ASA-6-302016: Tear down UDP connection 87447908 for OUTSIDE:68.22.26.66/4500 to inside:172.16.9.10/4410 duration 0:27:49 bytes 18653

View 1 Replies View Related

Cisco :: ASA Ipsec Pass-through To Nortel VPN Server?

Apr 17, 2011

For the moment we run a Nortel VPN server at work and I have on my laptop the Nortel VPN client. While I could connect through when I had my Linksys E2000 connected up now I can't after I replaced it with the 5505. (running 8.4(1).) what I should do on my 5505 so I can allow the nortel client to connect out?

View 6 Replies View Related

Cisco Firewall :: ASA 5520 VPN Tunnel Up But Not Traffic

Nov 1, 2012

We just migrated from a single 5510 to a dual (failover)  5520, It seems that everything is working except the remote VPN. We can establish a tunnel and authenticate as local users, (going to LDAP when all is working) but no traffic is passing. I know I am overlooking something but cant see it. [code]

View 12 Replies View Related

Cisco Firewall :: 5520 VPN Traffic Between Interfaces

Jun 12, 2011

Our ASA 5520 firewall is running 8.0(4) IOS.I have an internal L2L VPN terminating on my firewall (from an internal remote site) on ENG interface.With the default "sysopt connection permit-vpn" command enabled, VPN traffic is allowed to bypass the ENG interface acl.The security level on the ENG interface is set at 50.The security level on the destination interface PRODUCTION is set at 40.Inbound VPN traffic bypasses ENG interface acl and since higher-to-lower security level allows VPN traffic to flow freely from ENG to PRODUCTION, it seems the only place to check/filter VPN traffic is an ACL placed on the PRODCTTION interface and set at INBOUND (outbound VPN traffic).

View 4 Replies View Related

Cisco Firewall :: Traffic Prioritization On ASA 5520?

Dec 1, 2011

I have a Cisco ASA 5520 (8.0) and I'm trying to figure out how to prioritize traffic to specific websites (by either domain names or IP addresses/ranges).  This document [URL] has some great examples, but I'm not able to create a class-map that will match addresses.  I'm not doing any other traffic manipulation on this ASA. 

View 1 Replies View Related

Cisco Firewall :: ASA 5520 - Allow Traffic Between DMZ Servers?

Dec 20, 2011

We can´t reach DMZ servers from other DMZ servers?If I make a ping from DMZ server to another, sometimes only recieve one ping, sometimes 4, sometimes 0.How can I allow the traffic between DMZ servers??
 
(ASA 5520 Version 8.4)

View 2 Replies View Related

Cisco Firewall :: 5520 - Traffic From Inside To Outside

Mar 2, 2011

I am setting up a pair of 5520 in A/S mode but the traffic from inside to outside seems blocked somehow.

asa01# sh run : Saved
ASA Version 8.3(1)
host name asa01
enable password LFJ8dTG1HExu/pWQ encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
[code]......

Base on the above configuration, I still cannot ping or HTTP.

View 10 Replies View Related

Cisco Firewall :: ASA 5540 - IPSec Tunnel / ASA Refuses To Encrypt Traffic But Decrypts It

May 31, 2012

This has to be the most weirdest issue I have seen since the past year on my ASA. I have an ASA 5540 running the 8.4(2) code without any issues until I stumbled upon this problem last week and I have spent sleepless nights with no resolution! So, take a deep breath and here is a brief description of my setup and the problem:
 
A Simple IPSEC tunnel between my ASA 5540 8.4(2) and a Juniper SSG 140 screen OS 6.3.0r9.0(route based VPN)
 
The tunnel comes up without any issues but the ASA refuses to encrypt the traffic but decrypts it with GLORY! below are some debug outputs, show outputs and a packet tracer output which also has an explanation of my WEIRD NAT issue:  

My setup - ( I wont get into the tunnel encryption details as my tunnel negotiations are **** perfect and comes up right off the bat when the ASA is configured as answer only)
 
CISCO ASA - IPSec networking details
LOCAL NETWORK - 10.2.4.0/28
REMOTE NETWORK - 192.168.171.8/32
JUNIPER SSG 140 - IPSec networking details
PROXY ID: LOCAL NETWORK - 192.168.171.8/32
REMOTE NETWORK - 10.2.4.0/28 
HOST NAME# sh cry ipsec sa peer <JUNIPER SSG PEER>
peer address: <JUNIPER SSG PEER>
[code]... 

As you can see, there is no echo reply packet at all as the packet is not being encapsulated while it is being sent back. I have been going mad with this. Also, this is a live production multi tenant firewall with no issues at all apart from this ****** ip sec tunnel to a juniper!!

Also, the 192.168.10.0/24 is another IP Sec tunnel remote network to this 10.2.4.0/28 network and this IP SEC tunnel has a similar Juniper SSG 140 screen os 6.3.0r9.0 at the remote end and this woks like a charm without any issues, but the 171 is not being encrypted by the ASA at all.

View 2 Replies View Related

Cisco Firewall :: ASA 5520 8.3 VPN Tunnel Drops Traffic

Aug 23, 2011

We have a 100 Mbps WAN circuit, we have configured an IPsec tunnel between ASA 5520 and Cisco 3845 Router for our DR site replication via Veeam Backup and Replication, it was working fine before, when we established the 3DES tunnel the traffic for certain subnets is dropped after an hour and it stops the replication, although tunnel remains up and we can access the other subnets, as soon as we clear the crypto SA and ISAKMP sessions on the firewall the traffic starts flowing again and then after an hour the traffic is dropped again.So far the testing and differnet configurations we tried are as under.
 
Tried with a different MTU size both on firewall and ESXi servers but nothing happened.Their is no QOS configuration.Checked the utilization on both ends its Noram although their are subsequent 100% spikes on Cisco 3845 but on average it remians at 30-40%.

View 6 Replies View Related

Cisco Firewall :: ASA 5520 Cannot Block Incoming Traffic

Dec 12, 2012

I was configure 3 interface on ASA1st - managemetn (only for management)2nd - gig0/0 is connected to internet with real IP3rd - gig0/1 is connected to local networkI was configure routed NAT to internet.But I have problem with restriction incomming traffic to inside interface (ifname is inside)but I can connect to ip address of inside interface from other ip. It is wrong and i can't understand where is my mistake.

View 2 Replies View Related

Cisco Firewall :: 5520 Can't Get Traffic From Inside To Internet

Nov 27, 2011

I am trying to make a basic config on my 5520. The first goal is to make trafic from inside to outside.The internet address is 64.28.29.200 and the default internet gw is 64.28.20.193What am I missing since I can not get trafic from inside to the internet? [code]

View 10 Replies View Related

Cisco Firewall :: Enabling Outbound Traffic Through ASA 5520 8.4(4)1

Apr 4, 2013

We've got a proyect that requires a few thin clients to connect to a remote PCoIP server.
 
Looking to the documentation, the only port required to be open through Firewalls is TCP/UDP 4172, however, we've seen (making interface captures) that it somehow also uses ESP (IP protocol 50).
 
We've got a static NAT translation translating those thin clients to a public IP address, we've created ACLs to allow inbound (shouldn't be necessary as our user is connecting to a remote server) and outbound traffic for TCP/UDP 4172 and ESP and I cannot make it work.
 
I've also enabled IPSec pass-through Inspection to no avail.
 
how should we configure our ASA to enable this kind of traffic?

View 4 Replies View Related

Cisco Firewall :: ASA 5520 - Allow All Traffic From Frame Relay

Jun 14, 2012

I am installing an ASA 5520 and I have a problem on accepring the incoming traffic from an external office connected via Frame Relay.
 
On my OUTSIDE interface I have both the internet traffic and the external office traffic incoming. What comes from the external office is visible as 10.1.0.0/16.
 
I have to allow this traffic to enter the internal network, without any control. I would also keep the original IP address.
 
I have configured the Firewall but I don't know how to setup the NAT.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved