I am migrating over from and old PIX to an ASA 5510. After configuring the new device everything else is functional (Internet) but users are unable to pass traffic when connected through the vpn, they are able to authenticate and I see their session connected on the ASDM but no data is passed..[code]
View 4 RepliesWe have a small cisco 1800 series workgroup router that seperates our network from the outside world. The data coming into our network goes into the router on interface fa0/1 and comes out on interface fa0/0. fa0/0 is split into 2 sub-interfaces (fa0/0.2 and 0/0.3). These sub-interfaces correspond to a desktop and server vlan on our network. The workgroup router is connected to a 3560G trunk port (we'll call it switch 1) and switch 1 connects to another 3560G (we'll call it switch 2). Recently I was asked to add another layer of security to our network by installing an ASA 5510 firewall and forcing certain types of traffic to authenticate using their domain credentials for our network. The firewall was set up between the router and switch 1 in transparent, multi-context mode. There are 2 security contexts, 1 for the desktop vlan and 1 for the server. Both have the same security settings applied to them since we want the same behavior regardless of whether they are trying to access the servers or the workstations.
View 2 Replies View RelatedI have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
I am trying to use a ASA 5510 with AnyConnect as an in-line SSL VPN device. I have a separate firewall that NAT's 443 to the inside IP of the ASA, which is the only configured interface on the ASA. I can connect to the ASA from the WAN just fine and the AnyConnect client connects just fine, I get an IP lease across the VPN on my LAN, all looks well. The problem is that I cannot pass any traffic. The only device on my LAN that I can ping is the ASA, nothing else including the default gateway is accessibe. I have setup a static route on the ASA pointing 0.0.0.0 0.0.0.0 to the LAN gateway, but no dice.
View 1 Replies View Relatedwe have two routers CISCO881-K9 and we have established l2tpv3 pesuduwire between two routers: attached the configuration file for both routers.
Although the l2tp established but we are unable to pass the DHCP or other traffic through l2tp tunnel from router A to router- B. [code]
below is my sanitized ASA 5510 config. got an IPv6 T1 from at&t and im unable to pass any traffic from my LAN clients out.
:
ASA Version 8.2(2)
!
enable password PoBmYYxuAzCciKRA encrypted
[Code].....
I restored the HA pair back to Active/Standby.
1 remaining issue.
I have 3 IPsec Site-to_SIte tunnels.
I noticed that when the NEW UNIT becomes ACTIVE that I am unable to pass traffic over the VPN tunnels.When I failback I am able to pass traffic.
I used the GUI configuration tool for this ASA 5505. When I install it no traffic passes. I am wondering to verify my config. I have masked the usernames for VPN with xxxxxx and yyyyyy. [code]
View 6 Replies View RelatedI am trying to setup my very first ASA5505 and I cannot get it to pass traffic from the inside to the outside. I am not using NAT/PAT. Here is what I have done so far.
ASA5505(config)# interface Vlan 1ASA5505(config-if)# nameif insideASA5505(config-if)# security-level 100ASA5505(config-if)# ip address 33.46.132.34 255.255.255.248ASA5505(config-if)# no shut
[Code]....
Then from the asdm I permited everything from inside to go out but I cannot get any traffic through. I can ping the outside if I source the outside interface but not if I source the inside. The logs would not show me anything.
I did a packet tracer and it indicates the implicit deny rule at the end of the access-list is stopping my traffic eventhough I have allow rules above it?
I also checked the box in the asdm to allow traffic to pass without NAT
i read cisco document:[URL] pptp client is in inside,pptp server is in outside.when i donot use firewall, the pptp connection can establish successfully.but use pix 525 7.0(7) i config:
inspect pptp.
pptp connection cannot setup.
show connection in pix:
pptp tcp 1723 is ok.
gre connection only one "E" flag, E means 'outside back connection'.i try second method:delete 'inspect pptp',permit tcp 1723 and gre traffic from outside to inside, and i have config static nat,but the pptp connection cannot work too.so i think there is a pptp bug exist in pix 7.0(7).
We have an issue where by we connect to various customers and the Cisco IPSEC remote access works fine from our LAN through an ASA5505 to a customer site.We have 1 customer that we have some issues with. We can connect from the LAN through to the customers VPN, authenticate and establish a tunnel but in we cannot pass traffic. When we try from outside of the office on a public internet connection the VPN works fine. What could cause this issue?
View 3 Replies View RelatedHow can I see the quantity of traffic that is passing through into an IPSec VPN in a ASA 5520.
View 3 Replies View RelatedI ' m not able to configure the asa 5510 to allow the multicast traffic to pass through ASA.The multicast traffic have to pass from inside interface to outside interface.Can I configure the multicast traffic to pass through asa with a static nat ?
View 1 Replies View RelatedI have installed asa 5520 , software ver is 8.4,I have SSM-20 installed in asa 5520. How to pass traffic through this ssm-20 ,how to create sensors,how to update signatures of this IPS module ,is there any procedure to automatically update the signatures .
View 1 Replies View RelatedI have a trouble with Cisco ASA 5510. I configured an SSL VPN with bookmarks to some application. When the users make access to the Web Portal they have to login twice: one for enter in the SSL and one for enter in the application.
How to bypass double authentication?
asa 5505 do not pass traffic as a patch cord, how to make it pass traffic? [code]
View 2 Replies View RelatedI have Users Connected via IPSec vpn using asa 5510 to my enterprise network,but i have seen that the user stay connected while he sleeping , now i need to tear down the tunnel if the inactivity is 15 mts,i mean if the user idle for 15 mts with any thing automatically disconnect him after 10 15 mts
View 5 Replies View RelatedI have a weird problem which I have already submitted a TAC ticket about. When users authenticate through AnyConnect into our HQ ASA 5510 they grab an address from 172.16.254.x. What we have been noticing intermittently is that when logged into our network through the client they are unable to access their resources at one of our remote offices which is connected over l2l to the HQ ASA. This problem just started randomly a week ago and we have been working with Cisco trying to create a solution.
My quick fix is logging into a device at the remote office which is trying to be accessed and pinging the gateway of the virtual subnet for AnyConnect users. When I ping 172.16.254.1 it goes through after a few dropped icmp packets and then the issue is resolved for about 8 hours or so.
I hava Cisco ASA 5520 with AIP-SSM module. I would like to have the below features with ASA installed in Transparent mode.
1. Traffic shapping per user
2. Traffic shapping per IP subnet
3. Traffic shapping per Application
Is it possible with ASA installed in Transparent mode?
I have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
I Have an asa 5510 running code 7.2 configured with ssl vpn,ssl vpn users able to connect to to portal which i have configured with the required resources,but the thing is that these ssl users unable to upload files to cifs shared directory , although they have full access to the shared folder
View 0 Replies View RelatedI configured one ASA 5510 firewall with CSC-SSM-10 in one of my customer location.
Here i want configure my firewall to send email alerts to particular mail ID, if anybody any access my network from outside( Like VPN users).
We have ASA 5520 with CSC-SSM 20 and we want to block https traffic but when we are blocking https traffic http traffic going to block but user are able to open website.
View 1 Replies View Relatedwhen u use the debug cryoto isakmp 127 on the asa 5510, in order to troubleshhot remote access vpn users,to which entry r u looking in the debug to see if the user enter wrong password?
View 1 Replies View RelatedHow to designate access-list for the remote access vpn users in order to let them access specific subnet or host,asa 5510 and acs is in the picture
View 9 Replies View RelatedWe have a ASA 5510 which was running 8.0.2, we recently upgraded it to 8.2.5 and since the upgrade remote users for exchange 2007 are not able to download any large email attachments(over or close to 1MB). This is only happening to Outlook anywhere users or OWA users who are connecting to the exchange server using https(443) externally. If the same users connects internally they do not face any issue. When i check the logs on ASA i am gettings lots of RESET-O and RESET-I entries. Looks like the connection between the client and the server gets reset.
View 14 Replies View RelatedHow many user accounts i can create to a Cisco ASA box? Say for example a Cisco ASA 5510 or Cisco ASA 5520?
View 5 Replies View RelatedI'm actually require authentication for users who are coming from the PublicVLAN (the vlan associated with the wireless hotspot) to authenticate themself to the LDAP server via my firewall ASA 5510
View 12 Replies View RelatedA former coworker of mine setup VPN capabilities to our office network shortly before he left. It is no longer working. We can connect to VPN but I'm not able to ping any devices on the remote network or Remote Desktop to any of the server. After 30 minutes, the VPN connection drops. I have attached our ASA 5505 config to assist in troubleshooting.
View 3 Replies View RelatedI can telnet to the router and ping places on the inside and outside. However when I connect a laptop to the inside interface I can ping to the outside for a bit but can't open a web page and then connectivity is gone all together. At first I thought it was a NAT issue but I know I am good on that front. I have attempted to change the speeds and duplex settings on the outside interface but it does not seem to work. Again if I take the cable from the outside interface and plug it into a laptop it works fine. The thing that makes me wonder is why can I connect to the outside interface and configure it just fine?
View 4 Replies View RelatedI have a issue that i am at a loss as how to solve it. I have an ASA 5505 as my firewall. I have users from other companies who visit from time to time and are unable to use their outlook email to send messages. They can however receive messages without a problem. I also have a situation where users who use windows live to access gmail are unable to send messages.
I have narrowed it down to the fact that these uses are using ssl/tls to send the mails. I did some research and found out about the inspect esmtp setting in the ASA. I have disabled it and i still have to problem. I have also removed all outbound deny statements and still no luck.
Of note is that i can send emails without attachments. They take a long time to go out ( from minutes to hours) but eventually they do. Emails with attachments of even 10k do not go at all.
I was running image 8.2.3 and i downgraded to 8.0.5...still did not work...i upgraded to 8.4.3...still did not work. I am now back at 8.2.3.
My Firewall config is attached. I am at my wits end as to what else to try. The company has not renewed support for the device so i am on my own here!
I have a classical "inside + DMZ + outside" configuration.I also have a mail server in DMZ which have to be allowed to reach any destination on the outside (internet) at least on the SMTP port, of course.If I make an access rule that allows traffic from that server to "any", everything works fine, but doing so the server is allowed to reach any destination, including what is behind the inside interface (internal network).I didn't find any other option to tell the ASA machine to allow any destination, but on the outside interface only.I do believe is possibile to have the ASA to allow any kind of traffic from a host on the DMZ to the outside interface only, but I didn't figure out how.
P.S.: I'm using a 5510 machine running version 8.2
A PC connected to a Cisco 877 router and 877 router is connected to another router (7301) via GRE tunnel,Cisco 7301 router is a NAS server and is being used as a PPPOE server.If user create a PPPOE connection on his computer and dial with a username/pass we want to send the PPPOE traffic to 7301 router, so 877 router should pass the PPPOE traffic to 7301 and user will be able to connect,User -> 877 -> 7301(PPPOE server).
View 4 Replies View Related