I am migrating over from and old PIX to an ASA 5510. After configuring the new device everything else is functional (Internet) but users are unable to pass traffic when connected through the vpn, they are able to authenticate and I see their session connected on the ASDM but no data is passed..[code]
I have a ASA 5510 firewall with CSC module and Security Plus license for CSC module.Will you tell me how to configure my firewall to send emails to particular mail ID when someone login into the firewall or any virus attacks from outside.
I have a an ASA 5520 connected to a Layer 3 (3750) switch (Inside) and a connection to a 2960 switch (Outside) to get to the internet. . I have created vlan interfaces on the 3750 switch and enabled ip routing on the switch to enable the vlans to communicate with each other.
Vlan Interfaces on the switch: Vlan 100 172.17.1 Vlan 200 172.18.1 Vlan 300 192.168.3.1
I want the devices connected to the 3 vlans to be able to pass through the firewall and get out to the internet.I have connected the ASA to the 3750 by routed interfaces (10.10.10.1) --------- (10.10.10.2) and they are able to ping each other.I have also put a default route on the 3750 sending all traffic from the switch to the ASA inside interface (10.10.10.1)The issue that i am having is that the ASA also connects to a 2960 which has a connection to the Internet, and they are handing off an ethernet connection from the 2960 that sits in VLAN 55 (Vlan 55 is the Internet accessible vlan).How do I configure my ASA to send all traffic from my (3) vlans to the interfaces that connects to the 2960 switch?
Configured ASA 5510 with CSC module and working fine.Here i likes to configure, Whenever any users from outside accessing my firewall (like VPN users) that logging information i need to send one particular mail ID.Simply, i likes to enable my fireawall to send logging information to one particular mail id.
I have a Cisco asa 5510. I am doing attack a my firewall, using n map. I am seeing in the log the attack but i like that firewall send only alarm of attack by email . I have active email with warning and i received very much email.
I observed that graph show attack, but not ip of attacker, is possible that Cisco asa show the ip too ? The log show scanning with n map but not shunning IP and not send alarm. How i can send alarm ? The graph no show ip, it's possible show it.
I have 2 subnets bought from my provider 188.8.131.52/27 and 184.108.40.206/27.
From my provider a have the following setup: IP Address: 220.127.116.11 Netmask: 255.255.255.128 Gateway: 18.104.22.168 DNS (1): 22.214.171.124 DNS (2): 126.96.36.199 My IPs are static routed by my provider thought 188.8.131.52 .
Everything works perfectly except when I try to sent an email. The email gets sent (eventually), but afert a long waiting time, 45-60 sec. The connection is opened instally to the server but then just hangs there for 40-50 sec. The problem is that a have an aplication on a server that has to send confirmation emails, and that aplication is limited to a 30 sec timeout for conecting to the mail server, much less then the 45-60 sec that I have now. The mail server is hosted by a data center, it is not in my networks (location).
I have tried deleting the ESMTP inspection, that doesn't work. Pinging my mail server rezults in a average time of 20 ms. And when a do a tracert the hight value in a hop doesn't usually pass 80 ms, the average is 20-25 ms.
The problem is ONLY when sending emails. Everything else works perfect, including receiving emails from the same server.
I have a classical "inside + DMZ + outside" configuration.I also have a mail server in DMZ which have to be allowed to reach any destination on the outside (internet) at least on the SMTP port, of course.If I make an access rule that allows traffic from that server to "any", everything works fine, but doing so the server is allowed to reach any destination, including what is behind the inside interface (internal network).I didn't find any other option to tell the ASA machine to allow any destination, but on the outside interface only.I do believe is possibile to have the ASA to allow any kind of traffic from a host on the DMZ to the outside interface only, but I didn't figure out how.
P.S.: I'm using a 5510 machine running version 8.2
Just wondering if there are any methods or commands, natively, in the asa5510 for determining all traffic in to and from a certain server passing through the asa. This would be without a syslog server or something similar.
Core Internal Network -> Cisco ASA 5510 -> DMZ Switch.If i send a ping reguest from internal network to servers in DMZ Switch over the ASA 5510, i can see a delay in response, some times this delay can be more than 80ms, this is a problem for the web applications in http traffic.How i can find what's happening on my ASA? I disable the inspect traffic over the IPS, disable the policy maps below, reload the two boxes, but doesn't works, the problem still persists. [code]
I'm currently using ASA 5510 with software 8.4.1 and I have an issue with nat configuration. I used the following config line:nat (inside, dmz) source dynamic LAN Pat1 destination Server1 Server1
The traffic is not flowing and when I use Packet Tracer, packets are dropped at the NAT rule with the following error: Drop-reason: (acl-drop) Flow is denied by configured rule.The only ACE I have is permit ip any any.
I have an ASA with an outside ACL that is configured to allow 184.108.40.206 SIP/5060 to 1x.x.x.46. I show no hits. I added an ACL to do a packet capture, it sees the packet coming into the ASA but not going to the Serv Prov interface. I see hits on the vuong ACL but not the production acl_out ACL.. What is up?
NOTE:ACL_out is the ACL we use to allow outside traffic to enter our network. FW1(config)# sh access-list | i 1.x.x.46 access-list acl_out line 1 extended permit ip host 63.x.x.140 host 1x.x.x.46 (hitcnt=0) 0xc09a9387 (*NO HITS) access-list acl_out line 658 extended permit udp host 220.127.116.11 host 1x.x.x.46 eq sip (hitcnt=0) 0x0f327179 (NO HITS) [code]...
It was tested and verified from the inside network to make sure the server is listening on that port. Below we created an ACL to allow all IP from another test PC to the Server IP 1x.x.x.46. We did a telnet to port 5060 and it showed hits but not on the acl_out ACL.
Below we applied the same ACL to the ServProv interface to see if traffic was going where it was supposed to . By trying to telnet to the 1x.x.x46 IP from 63.x.x.140 IP. Looking below, no traffic appeared on the capture2.
I have manually configured the Firewall ASA 5510 from existing PIX to match the configuration, however when I connect the firewall to the Network, no traffic is flowing in either direction. I have the Inside network on the 172.29.0.0 subnet and the outside network on 18.104.22.168 subnet. I am attaching the cofiguration file.
I use ASA 5510 and I would like to log VPN traffic ( for example, as soon as a remote user try to connect to the asa). I would like this log be send to a specific mail address. I already configure Email Logging for severity ( level 3) and it works well.
i would like to use ISP2 for all http/https/ftp traffic.how could I force my ASA to set a different gateway for http/https/ftp traffic ?i have tried several solutions such as nat/pat rules, nothing seems to work.
FTP traffic routed from outside to the inside interface works fine. I have another interface with multiple sub-interfaces and vlans configured. FTP traffic routed from the outside to vlan2_servers is not making it through the firewall. I must be missing something. I have attached my config.
I have ASA 5510 8.4 Firewall where more than 20 Site to Site VPN Clients are configured on it. how to see the traffic for one Specific Site to Site VPN.Actually this site to site vpn is always keep dropping for every minute. I'm sure its a problem at the other end.The remaining 19 VPNS are UP and working without any problem. How to see the traffic for specific vlan.More over we dont have any syslog server in our network. Is their any chance we can check the traffic on the firewall?
I have a private network behind a configured Cisco ASA 5510. I need to send data back and forth between a server on the inside network and a device on the outside network on port 44818. No amount of configuration is allowing this to happen. The packet tracer always fails on of the implicity "deny" rules, even though my other rule should explicitly permit it. I also realize I need to set up routing from my outside network to the inside network, but I cannot see from the documentation how to do that on this particular port without simultaneously breaking my outside connection.
The inside IP for the ASA is 192.168.25.1 The outside IP for the ASA 192.168.11.54
Here is my current configuration:
: Saved : Written by enable_15 at 08:49:25.956 UTC Thu Feb 2 2012 ! ASA Version 8.2(5)
I have little experience with firewalls, what I've learned has been by dealing with issues like this that arise from time to time.I know, I need to upgrade the version. It's in the works now. Anyways, my question/problem is: Today I've received reports of slow internet access/activity and have noticed myself that it seems a bit slow today. On the dashboard of our asa 5510 the "outside interface" traffic usage is running contstantly high. It's at the top of the graph. How can I tell what is causing the spike in utilization. It usually runs at about 1500-2000 Kbps, and now it's up over 10,000.
We are using an ASA 5510 as our gateway to our ISP. All of our VOIP traffic is sent to an Internet SIP provider for our outbound calls. Our pipe to the Internet is 100Mbps metro ethernet. I am trying to find a way to provide QoS for this traffic so that I can reserve 20Mbps of the available 100Mbps pipe for VOIP traffic.From what I've been able to figure out so far I would use a combination of priority queues and traffic policing. However, it seems that this is nearly impossible to accomplish because I cannot control the remote device that my ASA connects to because it is the ISP device. I could police traffic on the inside interface of the ASA. However, lets say that a client on our network starts downloading from an Internet host and the downloaded traffic saturates my Internet connection. I could police this incoming (from the Internet) traffic on my outside interface of the firewall. This would drop the packets but the bandwidth would have already been used by the time it reaches my firewall.Would the fact that I'm policing incoming traffic on my outside interface cause the sender to throttle down their transmit rate because packets are being dropped? Would this achieve my goal of guaranteeing available bandwidth for my VOIP traffic by not allowing other traffic to saturate the link?Most documents I find regarding this topic describe providing QoS for VOIP traffic traversing a VPN connection in which case you could configure both end devices.
We have Cisco ASA 5510 256RAM running 8.2.4 with CSC 6.3.1172.4, it slows down internet traffics drastically when we do speed test, we get something like this, It the computer is bypassing the CSC, it gets This was done when there's very low traffic on the LAN and CPU is low usage on the CSC. The CSC has been re-imaged also but still doesn't solve the problem.
Recently moved into the hardware firewall space and have a ASA 5510. Having some issues trying to get traffic through the box to my 4 dedicated servers. all the servers have static IP's and are connected to a private switch into one of the ethernet ports on the firewall(0/2). Public internet connection into another(0/0). 1 of my servers has a connection to the management port, and the public switch, and this is the one im trying to do the configuration on.
Im unsure what to set the IP address of my "outside" interface as. need to have RDP,FTP, HTTP traffic going to each of the 4 servers independently, pretty sure i can get the rules in place to allow this, but cant seem to get any traffic to go through the firewall to any of the other 3 servers.
I would like to know if there is a way to apply in the Cisco asa 5510 traffic shaping not for a interface but a single IP address.For example i would like to limit the bandwith for the IP address of my FTP server.
I have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 22.214.171.124 i dont get any reply.The runing config is below for ur ref :