Cisco Firewall :: ASA 5520 8.3 VPN Tunnel Drops Traffic
Aug 23, 2011
We have a 100 Mbps WAN circuit, we have configured an IPsec tunnel between ASA 5520 and Cisco 3845 Router for our DR site replication via Veeam Backup and Replication, it was working fine before, when we established the 3DES tunnel the traffic for certain subnets is dropped after an hour and it stops the replication, although tunnel remains up and we can access the other subnets, as soon as we clear the crypto SA and ISAKMP sessions on the firewall the traffic starts flowing again and then after an hour the traffic is dropped again.So far the testing and differnet configurations we tried are as under.
Tried with a different MTU size both on firewall and ESXi servers but nothing happened.Their is no QOS configuration.Checked the utilization on both ends its Noram although their are subsequent 100% spikes on Cisco 3845 but on average it remians at 30-40%.
View 6 Replies
ADVERTISEMENT
Nov 1, 2012
We just migrated from a single 5510 to a dual (failover) 5520, It seems that everything is working except the remote VPN. We can establish a tunnel and authenticate as local users, (going to LDAP when all is working) but no traffic is passing. I know I am overlooking something but cant see it. [code]
View 12 Replies
View Related
Jan 15, 2012
I have a site to site tunnel between two 5520 ASAs. Tunnel is up but when I try to talk to the other side, the implicit deny on the inside interface of the local ASA blocks the traffic. When I ping, the tunnel comes up but in the logs it says it is blocking icmp from inside to outside. I have tried the sys opt connection permit-vpn but it is not working. The traffic is from 5 specific machines within the local sub net that I put in a network object group called Celerra_Replication.
I want to them to be able to talk to 5 machines on the far end of the tunnel in a seperate sub net. They are in a net wrok object group called GP_Celerra_Replication The ACLs I created for this appear to be created correctly allowing IP from Celerra_replication to GP_Celerra_Replication and the opposite on the other side.
View 1 Replies
View Related
Sep 7, 2011
I have a two ASA 5520's and I want to be able to see or monitor the traffic between each tunnel. I am using external addresses but for the sake of this question I will use the following: 1.1.1.1 to 2.2.2.2 . How can I montior the traffic?
View 3 Replies
View Related
Feb 14, 2013
we have a L2L-VPN-Tunnel beetween our Headquarter (ASA5520 with Network 10.100.1.0) and a branch office (Cisco1841 with network 10.100.10.0 ). This works fine for years, but now we wish to change the configuration so that ALL traffic from the branch office goes over the vpn-tunnel. My question: How I have to change the crypto acl to reach this. Below the relevant parts of the branch route.
View 6 Replies
View Related
Apr 29, 2012
I have an ASA 5520 with the below config
Gi0/0: outside (Internet)
Gi0/1: inside (Internal users)
Gi0/2: DMZ (web servers, ftp, Mail etc..)
I have a SMTP relay deployed on the DMZ for mailing. I have also a mail servers installed in the internal lan,
I want to allow trafic from dmz to reach internal lan, and i want normally also allow stmp relay from dmz to reach Internet.
How can i block trafic from DMZ to reach Internal Lan (instead of smtp) if the to allow trafic from dmz to internet i must put ANY in the policy?
For allowing trafic from DMZ to reach Internet, the policy must be DMZ -----> ANY ----->Services., this policy means DMZ can implicity reach Internal Lan?
View 2 Replies
View Related
Jan 29, 2013
ASA 5520 running 8.4.5:We had an issue with a remote SMTP connection getting screwed up as a result of ESMPT inspect.It took me 3 hours of troubleshooting the SMTP connection before finally figuring out that the firewall was the culprit. What really through me off was that I saw nothing in the ASA logs (warning and above) that showed packets were being dropped. I'm probably crazy but I thought I remembered seeing entries in the log when packets were dropped due to a type of inspection (specifically, I remember entries in the log saying something to the effect of packet dropped due to ESMPT inspect, packet too big). My quesiton to Cisco TAC was: Is there a simple way to have the log give a warning every time a packet is dropped due to any inspection rule, just like we can see any drops due to ACLs? So far the only answer has been a complex list of log changes to allow debugging and notifications of certain events. This isn't something I want to roll out to all my ASAs.
View 5 Replies
View Related
Oct 9, 2011
We are looking to deploy an ASA 5520, but I need to know if it is possible for it to work in this environment.
We have colo space, with two IP ranges. They provide two network drops, one from each switch connected to different routers. One in which has 4 usable IP's for management purposes. This address range will be used only for remote access to the ASA and VPN into the management VLAN. The management VLAN will have all internal devices such as the switches, etc. The second range is for the servers, of which will be assigned directly to the hosts and the ASA will need to act as just a firewall. I can do this on IOS, but not sure about the ASA.
I need to answer the following questions:
Does the ASA support dual network drops, and would this be a failover port configuration in order for it to work?A management VLAN with outbound internet access only, and VPN/RA capability. NAT will need to be used I'm guessing. Can we have a DMZ VLAN which has defined ports, say 80, 443 and 25 inbound and outbound. I need the hosts to have the public IP assigned to them with no NAT configuration.
I know there are some advantaged to using NAT, but I really can't use it because the applications behind prefer public IP's being assigned to them.
View 23 Replies
View Related
Jan 11, 2012
I am getting the below messages in my cisco asa 5520, during this time tunnel is down. just what to check whether the problem is at remote FW or with asa
[code]...
View 4 Replies
View Related
Oct 17, 2011
I have a site to site VPN between SiteA to SiteB which is working fine. SiteA has an ASA5520 and SiteB Pix501. The ASA5520 is running version 804 with split tunneling. Users connect to SiteA using remote access VPN. Is it possible to setup SiteA ASA5520 so that when users connect to SiteA they can access servers located on SiteB through the tunnel? I know i can setup the Pix501 for remote access VPN but it is located in another country and i don't want to take a chance just incase i lose connectivity.
View 7 Replies
View Related
Jul 18, 2012
I have the following setup
|| Socks Server || >> Switch1 >> ||Cisco 5520 ASA || -->> | Switch 2| -->> Clients
I have a SSH SOCKS tunnel set up on the socks server which is a Linux box. When I connect my machine to the switch 2, I am NOT able to receive and mail by setting up a mail client and it seems SOCKS traffic does not reach the socks server. I can however run a telnet command on port 1080 (socks port) which connects which shows that the port was going through and open. However there was no SOCKS traffic. When I connected the machine to Switch 1, SOCKS traffic worked as expected and I was able to receive mail.
This suggests to me that the ASA has some inherent rule that does not allow SOCKS traffic. IS this true and if so how can I bypass this?
View 4 Replies
View Related
May 21, 2012
I'm attempting to configure two ASA 5520 for active/standby failover.When I enter the “failover” command to enable the config on the primary ASA, the entire routing table disappears.There is no routing process running, only static routes are configured.
Is this an expected behavior of the failover process and if so, how long should I wait for the routes to come back?
View 5 Replies
View Related
Dec 27, 2011
Monitor a VPN tunnel that has as end devices a Cisco ASA 5520 and a NetScreen Firewall. I'll like to be receive an alert when the VPN is down.
View 1 Replies
View Related
Apr 11, 2013
I'm trying to achieve a site-to-site ipsec tunnel to a Cisco ASA 5520. Most examples feature the ASA with a public interface that terminates the tuennel and a private network on another interface that the tunnel interacts with. Where my scenario differs is that the interface that accepts the tunnel is part of a public /29 network where I want the remaining hosts on that subnet to be able to route thrugh to the other end of the tunnel. My tunnel gets established, but any attempts to route via the IP assigned to that one interface result in the ASA rejecting traffic. If so, what configuration options should I consider?
View 5 Replies
View Related
Jan 7, 2013
Need to check how many tunnels IPSEC are running over ASA 5520.Tried commands which we use on Routers no luck?
View 6 Replies
View Related
Apr 8, 2011
Our Local Network is behind the CISCO ASA Firewall.Whenever we are accessing to Client VPN server,it is getting connected but after few Minutes (May be 5/10/30 Min),the sessions are terminating. The same traffic through PIX is no issue , only with ASA Firewall. See the following Error and request you give the possible root cause for this.
2011-04-09 16:15:09 Local4.Info 172.16.1.68 %ASA-6-302016: Tear down UDP connection 87447908 for OUTSIDE:68.22.26.66/4500 to inside:172.16.9.10/4410 duration 0:27:49 bytes 18653
View 1 Replies
View Related
Jun 12, 2011
Our ASA 5520 firewall is running 8.0(4) IOS.I have an internal L2L VPN terminating on my firewall (from an internal remote site) on ENG interface.With the default "sysopt connection permit-vpn" command enabled, VPN traffic is allowed to bypass the ENG interface acl.The security level on the ENG interface is set at 50.The security level on the destination interface PRODUCTION is set at 40.Inbound VPN traffic bypasses ENG interface acl and since higher-to-lower security level allows VPN traffic to flow freely from ENG to PRODUCTION, it seems the only place to check/filter VPN traffic is an ACL placed on the PRODCTTION interface and set at INBOUND (outbound VPN traffic).
View 4 Replies
View Related
Dec 1, 2011
I have a Cisco ASA 5520 (8.0) and I'm trying to figure out how to prioritize traffic to specific websites (by either domain names or IP addresses/ranges). This document [URL] has some great examples, but I'm not able to create a class-map that will match addresses. I'm not doing any other traffic manipulation on this ASA.
View 1 Replies
View Related
Dec 20, 2011
We can´t reach DMZ servers from other DMZ servers?If I make a ping from DMZ server to another, sometimes only recieve one ping, sometimes 4, sometimes 0.How can I allow the traffic between DMZ servers??
(ASA 5520 Version 8.4)
View 2 Replies
View Related
Mar 2, 2011
I am setting up a pair of 5520 in A/S mode but the traffic from inside to outside seems blocked somehow.
asa01# sh run : Saved
ASA Version 8.3(1)
host name asa01
enable password LFJ8dTG1HExu/pWQ encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
[code]......
Base on the above configuration, I still cannot ping or HTTP.
View 10 Replies
View Related
May 31, 2012
This has to be the most weirdest issue I have seen since the past year on my ASA. I have an ASA 5540 running the 8.4(2) code without any issues until I stumbled upon this problem last week and I have spent sleepless nights with no resolution! So, take a deep breath and here is a brief description of my setup and the problem:
A Simple IPSEC tunnel between my ASA 5540 8.4(2) and a Juniper SSG 140 screen OS 6.3.0r9.0(route based VPN)
The tunnel comes up without any issues but the ASA refuses to encrypt the traffic but decrypts it with GLORY! below are some debug outputs, show outputs and a packet tracer output which also has an explanation of my WEIRD NAT issue:
My setup - ( I wont get into the tunnel encryption details as my tunnel negotiations are **** perfect and comes up right off the bat when the ASA is configured as answer only)
CISCO ASA - IPSec networking details
LOCAL NETWORK - 10.2.4.0/28
REMOTE NETWORK - 192.168.171.8/32
JUNIPER SSG 140 - IPSec networking details
PROXY ID: LOCAL NETWORK - 192.168.171.8/32
REMOTE NETWORK - 10.2.4.0/28
HOST NAME# sh cry ipsec sa peer <JUNIPER SSG PEER>
peer address: <JUNIPER SSG PEER>
[code]...
As you can see, there is no echo reply packet at all as the packet is not being encapsulated while it is being sent back. I have been going mad with this. Also, this is a live production multi tenant firewall with no issues at all apart from this ****** ip sec tunnel to a juniper!!
Also, the 192.168.10.0/24 is another IP Sec tunnel remote network to this 10.2.4.0/28 network and this IP SEC tunnel has a similar Juniper SSG 140 screen os 6.3.0r9.0 at the remote end and this woks like a charm without any issues, but the 171 is not being encrypted by the ASA at all.
View 2 Replies
View Related
Dec 12, 2012
I was configure 3 interface on ASA1st - managemetn (only for management)2nd - gig0/0 is connected to internet with real IP3rd - gig0/1 is connected to local networkI was configure routed NAT to internet.But I have problem with restriction incomming traffic to inside interface (ifname is inside)but I can connect to ip address of inside interface from other ip. It is wrong and i can't understand where is my mistake.
View 2 Replies
View Related
Mar 20, 2013
How can I see the quantity of traffic that is passing through into an IPSec VPN in a ASA 5520.
View 3 Replies
View Related
Nov 27, 2011
I am trying to make a basic config on my 5520. The first goal is to make trafic from inside to outside.The internet address is 64.28.29.200 and the default internet gw is 64.28.20.193What am I missing since I can not get trafic from inside to the internet? [code]
View 10 Replies
View Related
Apr 4, 2013
We've got a proyect that requires a few thin clients to connect to a remote PCoIP server.
Looking to the documentation, the only port required to be open through Firewalls is TCP/UDP 4172, however, we've seen (making interface captures) that it somehow also uses ESP (IP protocol 50).
We've got a static NAT translation translating those thin clients to a public IP address, we've created ACLs to allow inbound (shouldn't be necessary as our user is connecting to a remote server) and outbound traffic for TCP/UDP 4172 and ESP and I cannot make it work.
I've also enabled IPSec pass-through Inspection to no avail.
how should we configure our ASA to enable this kind of traffic?
View 4 Replies
View Related
Jun 14, 2012
I am installing an ASA 5520 and I have a problem on accepring the incoming traffic from an external office connected via Frame Relay.
On my OUTSIDE interface I have both the internet traffic and the external office traffic incoming. What comes from the external office is visible as 10.1.0.0/16.
I have to allow this traffic to enter the internal network, without any control. I would also keep the original IP address.
I have configured the Firewall but I don't know how to setup the NAT.
View 2 Replies
View Related
Jun 28, 2011
When I try to configure the Botnet Traffic filter with the commad "dynamic-filter use database" through the ASDM I get the following error message.
[ERROR] dynamic-filter use-database Dynamic Filter: New data file not terminated with newline
View 14 Replies
View Related
Jan 9, 2011
i have a 7201 router with NPE-G2. i have a design which i have the option to send all the traffic through a GRE tunnel or a L2TPV3 tunnel.which method is more CPU consumption ?
View 1 Replies
View Related
Jun 20, 2011
I have installed asa 5520 , software ver is 8.4,I have SSM-20 installed in asa 5520. How to pass traffic through this ssm-20 ,how to create sensors,how to update signatures of this IPS module ,is there any procedure to automatically update the signatures .
View 1 Replies
View Related
Apr 6, 2011
I have a handheld device that will be used for inventory outside of our office. It has 3g capabilities. Is there anyway I can permit traffic from this device from the outside world coming into my network? I need to open a couple of ports so it can hit the server. But I have no intention to open these ports up to the entire world. I use an ASA 5520 with a managed router from our provider. I looked around on the Cisco site and the only information I found was for permitting and denying traffic from devices that are within the network.
View 2 Replies
View Related
May 14, 2012
how can i check that ASA is passing traffic? Also what command we can use to make sure VPN is working fine.
View 2 Replies
View Related
Sep 26, 2011
i have an ASA 5520 8.4(1) with following config
interface GigabitEthernet0/0
nameif WAN
security-level 0
ip address 216.52.185.33 255.255.255.240 standby 216.52.185.34
!
i need traffic (port 9350) from DMZ and WAN forwarded to object Production_23 port 3389, how do i achieve this ?
View 1 Replies
View Related
Apr 5, 2011
I hava Cisco ASA 5520 with AIP-SSM module. I would like to have the below features with ASA installed in Transparent mode.
1. Traffic shapping per user
2. Traffic shapping per IP subnet
3. Traffic shapping per Application
Is it possible with ASA installed in Transparent mode?
View 9 Replies
View Related
