Cisco Switching/Routing :: Requirements For Line Card Upgrade On WS-C6509-E
Jan 14, 2013
We are planning to replace a few line cards in the existing 6509-E chassis. The sup installed is a VS-S720-10G-3C but the line cards are legacy. As a result we are not able to enable the VSS functionality. We are looking to replace the existing line cards with the following:
1. 1 x WS-X6716-10G-3C
2. 1 x WS-X6724-SFP
3. 4 x WS-X6724-GE-TX
What are the requirements in terms of IOS and Roman.
The current IOS is: Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
And the ROM Version is: ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
Do I need an upgrade?
View 3 Replies
ADVERTISEMENT
Oct 14, 2012
We would like to install a WS-SVC-WISM2-1-K9 in each of our 2 WS-C6509-E chassis. Both of these have supervisor 720 engines installed. One in each chassis.From what I have read we need to upgrade the IOS to 12.2.33 SXJ4. Is this correct?If this is true then what are the memory requirements for the upgrade to this IOS version. Below is the output from Show version?Is there sufficient memory instqalled to do this install?
View 3 Replies
View Related
Dec 5, 2011
I have a cisco 1941 router. Stock standard vanilla hardware, no extras. Standard universal image. Data and Security not enabled.I would like to add a 4 gigabit port POE switch (EHWIC) module to the router..The 4 port POE switch module will be used to power and connect 2 x Areonet AP's for my home. I'm replacing a Apple Airport Extreeme and Express setup. I'll possibly later use the two remaining POE ports for security cameras.My question is, what extra hardware and or IOS version do I need for the POE swtich module to function on the 1941? [URL] I think this is the model I want EHWIC-4ESG-P #4 port 10/100/1000 Enhanced High-Speed WAN Interface Gigabit Ethernet switch with Power over Ethernet?
View 1 Replies
View Related
Oct 18, 2012
I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies
View Related
Jun 30, 2008
Cisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
View 2 Replies
View Related
Mar 20, 2012
when replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?
View 2 Replies
View Related
Nov 28, 2011
direct me to a document detailing the order that line cards are supposed to boot in a 6500? I'm noticing random boot sequences in some of my chassis,?Note: We currently run Sup720 3CXL for the most part.
View 6 Replies
View Related
Jan 26, 2013
The WS-X68xx series line card has a fabric of 40Gbps and a 16 Port 10GE has a 4:1 oversubscription rate. The WS-X6908-10G has a fabric speed of 80Gbps and has a 1:1 oversubscription rate.
If I mixed the 68xx and 69xx series line card, do I get 80Gbps for the 6900x and 40gbps for the 68xx line card? Or would the 69xx series line card be downgraded to 40Gbps?
From my understanding, the 68xx series has a DFC card and thus the fabric speed operates independently.
View 1 Replies
View Related
May 27, 2012
We currently have a WS-C6506 chassis with a line-card WS-X6408A-GBIC. Currently we need to replace the chassis by a Ws-6504-E and also the line-card. My question is: What must buy line-card and meets the same specifications of WS-X6408A-GBIC?.
View 4 Replies
View Related
Jan 17, 2012
Is it possible to use a 10GE interface on a sup720 and an interface from a 671610GE line card and create a port channel. I haven't found specific documentation on CCO stating you can. I have found the QOS queuing is differnet between the sup and line card.
View 1 Replies
View Related
Mar 26, 2012
Cisco announced EOL for ws-x6148A-GE-45AF line card and proposed WS-X6148E-GE-45AT. However this card seems not to be supported by the SUP2T-10G supervisor. Which alternative card should I take for this EOL line card, or can I use the proposed line card (use extra daughter card DFC4)?
I'm looking for an alternative line card for the 650x-E chassis with Supervisor 2T iso 6148-GE-45AF
View 7 Replies
View Related
Aug 6, 2012
On a number of 6500 chassis it appears that linecard 3 did exist at somepoint, but was removed.Problem is that when issuing the 'show int desc' or 'show ip int brie' the ports for the still appear, and indeed same with 'show run' and 'show conf'.
View 1 Replies
View Related
Jun 24, 2012
I need to pull a WS-X4712-SFP+E line card from an online 4507 chassis, can this be done, or does it need to be offline?
View 2 Replies
View Related
Oct 12, 2012
I've 4500 Core Switch with 4507R chassis, Sup V-10GE(WS-X4516-10GE) along with 2 WS-X4306-GB line Cards, but now I require a line card for 14 more fiber up links and I cannot go with 3 of 4306 as there are only 2 slots left. I've checked and found that E series line cards does not work with Sup V Engine.
As per the link below, I found that "WS-X4448-GB-SFP" is compatible..
[ URL]
View 1 Replies
View Related
Apr 15, 2012
I am writing with regard to a high memory utilization that we have on a pair of line card WS-X6748-GE-TX and WS-X6724-SFP for a VSS 6500. I am enclosing a little part of the "show tech"of this VSS 6500 where is possible to see the high memory utilization of the line cards 1/1, 1/2, 2/1, and 2/2, in despite of having some ports in state connected. In addition of this, the IOS installed on VSS 6500 is s72033-ipservicesk9_wan-vz.122-33.SXI6.bin for checking if there are some bugs affecting the behaviour of the Switch for this case.
System Resources
PFC operating mode: PFC3C
Supervisor redundancy mode: administratively sso, operationally sso
Switching resources: Sw/Mod Part number Series CEF mode
1/1 WS-X6748-GE-TX CEF720 CEF
1/2 WS-X6724-SFP CEF720 CEF
[code]....
View 1 Replies
View Related
Mar 19, 2013
Does Nexus 7K support Multiple VDCs sharing ports on a single line card. One of our cisco parnter engineers stated that cisco doenst recommend using same line card for multiple VDCs.The second VDC (Non-Default VDC) will be used four our Outside, and DMZ Segment, and to phyiscally segregate our Firewall from our Internal/Inside Core Switch without using a physical DMZ Switch.I know Cisco used the Nexus in this way in their PCI DSS 2.0 Compliance Document. Module is N7K-M148GT-11L
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 10/100/1000 Mbps Ethernet XL Mod N7K-M148GT-11L
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 10/100/1000 Mbps Ethernet XL Mod N7K-M148GT-11L
View 7 Replies
View Related
Mar 9, 2012
we plan to implement VSS on our datacenters (C6509/Sup720), in order to remove L2 loops (currently, access layer are C3750 stacks, which could evoluate for N5K/N2K). I would like to have some feedbacks about VSS stability. Some years ago, I have seen some bugs with this technology in another company, so I am still not totally comfortable to use it in the datacenter.
View 0 Replies
View Related
Apr 4, 2012
We plan to implement a large number of ACL on our Distribution switch which is a HSRP pair of 6509C switches running on sup-bootflash:s72033-psv-mz.122-18.SXD3.bin WE need to divide the Network in three layers
unsecure layer
Proxy layer
Secure layer
We have approximately 250 vlans on the our distribution switches and plan to implement 15 ACL on different vlans Each ACL can contain upto 30 lines or less.
basic ACL example we will be applying on different vlan
vlan 200
ip access-group test123 in
My question is Can these ACL on a vlan can have a massive impact on the 6509 CPU ?
View 1 Replies
View Related
Jan 13, 2013
I have a 2 cisco core (cisco WS-C6509-E (R7000) processor) and been working for quite sometime.they are conneted with HSRP with active standby config with a 10 g module for redundancy just today I see that the cpu utilization went to about 50% and its the same on both cores.
[Code] .......
View 5 Replies
View Related
Feb 26, 2012
Last night, the C6509-E do a unexpected reload. In the crashinfo, I can see that the last error message before the reload, was as follows: %C6K_ PLATFORM-SP-2-PEER_RESET: SP is being reset by the RP
I consulted the cisco website about this error message and what I found was the following:C6K_PLATFORM-2.
View 1 Replies
View Related
Sep 26, 2012
what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
View 2 Replies
View Related
Apr 1, 2013
I operate between c6509-E, what did you flooding? its just packet capture gi1/3 but i dont know it and is it attack?also same seq no switch gots it?what is problem?
View 2 Replies
View Related
Mar 25, 2012
we have a WS-C6509-E WITH SUP VS-S720-10G, and IOS s72033-advipservicesk9_wan-mz.122-33.SXI5.bin. [code]
From, what we can see, whenever we try to clear arp-cache, it doesn't remove the IPs from the ARP. We've checked a bug in the IOS 12.2(33)SXH4 with the same issue, in version SXI4 is solved, but I have version SXI5, it is supposed to be fixed, from this caveat CSCtf16300, since it says it was fixed on 12.2(33)SXI4, it should be fixed on SXI5, right ?
View 2 Replies
View Related
May 14, 2013
I need to choose router for my network. I don't have any special need, besides Internet connection and DHCP for some guest clients.There are around 30 IP phones (static IP), 30 PCs (static IP), and 10 wireless APs (users get dynamic IP). Maximum load is 5 phones, 5 PCs and 20 phones/laptops connected via wi-fi.
I guess I should go for Cisco 800 series. Would model 861 be good or I will need 881 or even 891?
View 3 Replies
View Related
Jul 8, 2011
Am currently running BT Voyager 2091 wireless ADSL router with BT Voyager 1055 wireless USB adapter. What system requirements does one need to upgrade to 802.11n. The OS is XP Pro x32 bit x86 based PC
View 1 Replies
View Related
Dec 22, 2011
Both regular IP traffic and ICMP traffic are passing through the source port. C6509 provides the option of filtering vlan traffic during monitoring. But I don't have vlan traffic.
qa-c6509-c(config)#monitor session 1 filter ? vlan SPAN filter VLAN
So I applied an access-list which only allows icmp traffic to be sent out of the monitoring port. But it does not work.
View 4 Replies
View Related
Nov 25, 2012
I have a C6509 with WS-X6548-GE-TX port module. The first port group, 1-8, is showing oversubscription (packets dropping) in the shared buffer. What interface commands can I use to find the specific port causing the buffer overflow?None of the ports is continuously overutilized and none of them in a SPAN destination group.I don't want to move connections without knowing which one is causing the problem. Also I fear that moving the connections may shift the bleeding to another shared port group.
View 2 Replies
View Related
Sep 9, 2009
I need those two stencils.I have checked here [URL] but:
- the one for the C6509-E is not there
- the one for the supervisor does not work properly (misaligned anchor points).
View 2 Replies
View Related
Oct 21, 2012
I have been looking at grading the IOS version on our 6509-E however there is not enough space on disk:0 to upgrade to the version I need to install. The question I would like to ask is - is it possible to boot the IOS from a TFTP server? If this is possible what configuration do I need on the 6509 to enable this. How does the 6509 know about the TFTP server as an IOS is not installed and therefore it will not have a network configuration
View 2 Replies
View Related
Jan 2, 2012
I have Cisco WS-C6509 with IOS version 12.2(18)I have several vlan interface on this device.Today I create new vlan intervace
interface Vlan165
description test5
ip address 10.10.10.1 255.255.255.252
end
and vlan:
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
165 test5 active Gi7/14
But I can't ping this IP address and show ip route shows:
sh ip route 10.10.10.1
Routing entry for 10.10.10.0/24
Known via "static", distance 254, metric 0 (connected)
I have static route for this subnet /24?I can not see any error in logs, but looks like I reached vlan interface limit on this device or something like this.How can I check it?
View 9 Replies
View Related
Sep 10, 2009
I am trying to figure out what is heat dissipation of a C6509-E configured as follows:
1 x WS-C6509-E-FAN
1 x VS-S720-10G-3C
1 x VS-F6K-PFC3C
8 x WS-X6748-GE-TX
8 x WS-F6700-DFC3C
2 x WS-CAC-6000W
I have tried two ways: 1) the power calculator and 2) manual calculation using the C6500 installation guide.
1) The power calculator says 13630 BTU/h
2) Manual calculation says: [code]
The there should be also the two PS in the picture, and the new total should be: [code] Well, 62711 BTU/h looks quite a bit too much and I think that the heat dissipation of the power supply should't be considered in the calculation.Isn't it an item that takes power from the grid and that generates heat according to its efficiency as the other modules?
View 2 Replies
View Related
Sep 19, 2012
Network newbie need to verify all necessary services and protocols on a new WS-C6509-E are turned on. This layer 3 switch will be used to connect to servers.
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
[Code]....
View 6 Replies
View Related
Mar 20, 2012
We have two c6509 budled in VSS. I have noticed randomly high usage of CPU, sometimes up to 99% in peaks. I have found that it can be generated by SNMP engine. So I unconfigure all SNMP things. But situation is the same. I would like to know if this state is OK or not. CPU shows are enclosed in file.
View 1 Replies
View Related
