we plan to implement VSS on our datacenters (C6509/Sup720), in order to remove L2 loops (currently, access layer are C3750 stacks, which could evoluate for N5K/N2K). I would like to have some feedbacks about VSS stability. Some years ago, I have seen some bugs with this technology in another company, so I am still not totally comfortable to use it in the datacenter.
View 0 RepliesCisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop" do not do the same job.
View 8 Replies View RelatedWe would like to install a WS-SVC-WISM2-1-K9 in each of our 2 WS-C6509-E chassis. Both of these have supervisor 720 engines installed. One in each chassis.From what I have read we need to upgrade the IOS to 12.2.33 SXJ4. Is this correct?If this is true then what are the memory requirements for the upgrade to this IOS version. Below is the output from Show version?Is there sufficient memory instqalled to do this install?
View 3 Replies View Relatedwe have some 2960 in my company and i'm looking to implement LLDP on them.But some are older than the other.tell me from which IOS the lldp is available ?
View 2 Replies View RelatedWe plan to implement a large number of ACL on our Distribution switch which is a HSRP pair of 6509C switches running on sup-bootflash:s72033-psv-mz.122-18.SXD3.bin WE need to divide the Network in three layers
unsecure layer
Proxy layer
Secure layer
We have approximately 250 vlans on the our distribution switches and plan to implement 15 ACL on different vlans Each ACL can contain upto 30 lines or less.
basic ACL example we will be applying on different vlan
vlan 200
ip access-group test123 in
My question is Can these ACL on a vlan can have a massive impact on the 6509 CPU ?
I have a 2 cisco core (cisco WS-C6509-E (R7000) processor) and been working for quite sometime.they are conneted with HSRP with active standby config with a 10 g module for redundancy just today I see that the cpu utilization went to about 50% and its the same on both cores.
[Code] .......
Last night, the C6509-E do a unexpected reload. In the crashinfo, I can see that the last error message before the reload, was as follows: %C6K_ PLATFORM-SP-2-PEER_RESET: SP is being reset by the RP
I consulted the cisco website about this error message and what I found was the following:C6K_PLATFORM-2.
what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
I operate between c6509-E, what did you flooding? its just packet capture gi1/3 but i dont know it and is it attack?also same seq no switch gots it?what is problem?
View 2 Replies View Relatedwe have a WS-C6509-E WITH SUP VS-S720-10G, and IOS s72033-advipservicesk9_wan-mz.122-33.SXI5.bin. [code]
From, what we can see, whenever we try to clear arp-cache, it doesn't remove the IPs from the ARP. We've checked a bug in the IOS 12.2(33)SXH4 with the same issue, in version SXI4 is solved, but I have version SXI5, it is supposed to be fixed, from this caveat CSCtf16300, since it says it was fixed on 12.2(33)SXI4, it should be fixed on SXI5, right ?
Both regular IP traffic and ICMP traffic are passing through the source port. C6509 provides the option of filtering vlan traffic during monitoring. But I don't have vlan traffic.
qa-c6509-c(config)#monitor session 1 filter ? vlan SPAN filter VLAN
So I applied an access-list which only allows icmp traffic to be sent out of the monitoring port. But it does not work.
I have a C6509 with WS-X6548-GE-TX port module. The first port group, 1-8, is showing oversubscription (packets dropping) in the shared buffer. What interface commands can I use to find the specific port causing the buffer overflow?None of the ports is continuously overutilized and none of them in a SPAN destination group.I don't want to move connections without knowing which one is causing the problem. Also I fear that moving the connections may shift the bleeding to another shared port group.
View 2 Replies View RelatedI need those two stencils.I have checked here [URL] but:
- the one for the C6509-E is not there
- the one for the supervisor does not work properly (misaligned anchor points).
I have been looking at grading the IOS version on our 6509-E however there is not enough space on disk:0 to upgrade to the version I need to install. The question I would like to ask is - is it possible to boot the IOS from a TFTP server? If this is possible what configuration do I need on the 6509 to enable this. How does the 6509 know about the TFTP server as an IOS is not installed and therefore it will not have a network configuration
View 2 Replies View RelatedI have Cisco WS-C6509 with IOS version 12.2(18)I have several vlan interface on this device.Today I create new vlan intervace
interface Vlan165
description test5
ip address 10.10.10.1 255.255.255.252
end
and vlan:
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
165 test5 active Gi7/14
But I can't ping this IP address and show ip route shows:
sh ip route 10.10.10.1
Routing entry for 10.10.10.0/24
Known via "static", distance 254, metric 0 (connected)
I have static route for this subnet /24?I can not see any error in logs, but looks like I reached vlan interface limit on this device or something like this.How can I check it?
I am trying to figure out what is heat dissipation of a C6509-E configured as follows:
1 x WS-C6509-E-FAN
1 x VS-S720-10G-3C
1 x VS-F6K-PFC3C
8 x WS-X6748-GE-TX
8 x WS-F6700-DFC3C
2 x WS-CAC-6000W
I have tried two ways: 1) the power calculator and 2) manual calculation using the C6500 installation guide.
1) The power calculator says 13630 BTU/h
2) Manual calculation says: [code]
The there should be also the two PS in the picture, and the new total should be: [code] Well, 62711 BTU/h looks quite a bit too much and I think that the heat dissipation of the power supply should't be considered in the calculation.Isn't it an item that takes power from the grid and that generates heat according to its efficiency as the other modules?
Network newbie need to verify all necessary services and protocols on a new WS-C6509-E are turned on. This layer 3 switch will be used to connect to servers.
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
[Code]....
We have two c6509 budled in VSS. I have noticed randomly high usage of CPU, sometimes up to 99% in peaks. I have found that it can be generated by SNMP engine. So I unconfigure all SNMP things. But situation is the same. I would like to know if this state is OK or not. CPU shows are enclosed in file.
View 1 Replies View RelatedWe are facing issue of getting very high CPU utilization for the VSS Switch model WS-C6509-E some times approx 100%.Attaching here show tech-support taken later after CPU normal along with show logging, show cpu sorted.HCAINNOI01XXXCS0001#sh proces cpu | ex 0.0%CPU utilization for five seconds: 100%/13%; one minute: 90%; five minutes: 91%PID 5Sec 1Min 5Min Process16406 91.2% 75.2% 76.2% ios-base16426 1.7% 1.4% 1.4% udp.proc16429 0.3% 0.3% 0.3% raw_ip.proc16432 2.8% 3.1% 3.1% cdp2.iosproc
View 3 Replies View Relatedwe have cisco WS-C6509-V-E with IOS version 12.2(33)SXI4; s3223_rp_IPSERVICESK9_WAN_M) running on a switch. I am trying to configure the command "mac-address-table synchronize" under global config mode. But when I enter the command Cisco(config)#mac-address-table ?It doesn't show the synchronize option?
View 3 Replies View RelatedI am trying to find a command for dhcp snooping rate-limiting on a CatOS. The PFC card is PFC. PFC3B is said to support that command. But there seems no this command.
-6k> (enable) sh ver
WS-C6509-E Software, Version NmpSW: 8.4(5)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Aug 3 2005, 13:26:46
[Code] ......
Up time is 1183 days, 1 hour, 41 minutes
We are planning to replace a few line cards in the existing 6509-E chassis. The sup installed is a VS-S720-10G-3C but the line cards are legacy. As a result we are not able to enable the VSS functionality. We are looking to replace the existing line cards with the following:
1. 1 x WS-X6716-10G-3C
2. 1 x WS-X6724-SFP
3. 4 x WS-X6724-GE-TX
What are the requirements in terms of IOS and Roman.
The current IOS is: Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
And the ROM Version is: ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
Do I need an upgrade?
I've a big problem with a loss of packets ICMP sent by different hosts in differents VLAN. Here my architecture:
Core Switch : 2 Switch's C6509 (Version 15.0 (1) SY1)- Mode VSS - One lien VSL , the other link is defective.Access Switch: C3750 , Connected to Core Switch through 2 fibre optique wires.Topology: redundant ring
When I send consecutive ping message I found always a missing of packets . Furthermore When I insert the "show ip traffic" command., the parameter "bad hop count" increase after a loss of packets. I've 2 hosts connected in my network and they send packets with TTL =127.
In the Core Switch I haven't configured the MEC because it gave me troubles with the packets multicast.
I have recently configured secondary ip address on LAN Interface of Cisco C6509.. We have some application which needs to use broadcast traffic communication to communicate with client... Broadcast is working within subnet & also working from broadcast server to primary subnet. But not working from secondary subnet.. I have checked broadcast within secondary IP range & it's working fine... Secondary not working broadcast with primary and also with broadcast server... broadcast address is different for these subnet but both should be communicate since configured on same interface... When I went through Cisco website found that command "ip directed broadcast" which will pass broadcast to different subnet... But I'm not sure whether any other impact if I enable that command on particular Ethernet interface...
View 6 Replies View RelatedThe OID I am using for module index 6509-E family is not working on 6509 Virtual Switching System(VSS).I have used "1.3.6.1.4.1.9.5.1.3.1.1.1" for single6509- E configuration. How to know OID for module index on VSS environment.
View 5 Replies View RelatedI have two cisco wlc 5508. I wan to install them in two differents site. One WLC in the site A and the another WLC in the site B.
Site B is the WAN of the site A. The site A is the headquarter.
But i need to configure them in High Availability. For example if the Cisco WLC in site A goes down, the ap's have to registered in the WLC of the site B.
Then the traffic LWAPP have to pass over the WAN between site A to site B.
I have to configure two cisco wlc in HA over a WAN . Is ok configure the roamming L3 intercontroller?
I'm polling a few thousand locations using IP SLA, I have responder enabled on all destinations, and I'm using 60 byte voice packets with a QoS policy.When I run an IP SLA Summary availability report, I have a bunch of locations showing 9% availability 8.5% etc. When I go to the actual collector, and pull up a graph of the same time period, that graph shows 100% availability.
Same collector, same data, just different views giving completely different results. I have to assume that the IP SLA summary report is wrong, these sites were not down 90% of the time.
Just a random though to go with that, I do have the IP SLA to only pull information during the locations operational hours, and I did pull the report from midnight to 11am, the statistics should have been gathered for 4 hours of the 11, which is still higher than 9%, and I would expect all of my locations to report like that, not just a few hundred.
All of the devices are similar in hardware and IOS, and I have verified on a handful that IP SLA responder is enabled, and I see the connections, I have also verified the source configuration via command line.
what fields of IT increase internet availability. I have lived in South Korea for the last six months. I can't say how much better life is because there seems to be universal high-speed internet access, even at 24/7 fast food places like Dunkin' Donuts, McDonalds, etc.).
View 3 Replies View RelatedOne of my customer wants to upgrade their Cisco ACS version from 4.0 to 5.3. The client has existing ACS version 4.0 windows on VM with two instance and need to upgrade to 5.3 Linux.As per my understanding following version are supporter to upgrade ACS to version 5.3 ACS 4.1.1.24ACS 4.1.4ACS 4.2.0.124ACS 4.2.1 but unfortunatlly there is running 4.0.I suggested to my client the upgradation for ACS and proposed this Upgrade lisence L-CSACS-53VMUP-K9 and CON-SAS-CSACS3V? how I can do the smooth deployment / Migration from 4.0 to 5.3 with (A/P)high availability.
View 1 Replies View RelatedCurrent environment is Cisco 2125 WLC managing ~12 3502E AP's for a single location. Client is looking to provide HA for the single 2125 WLC. With the 2125 now EO-Sale is it possible to go with one additional 2504 WLC and leverage the existing 2125 or would it require going with just (2) 2504's?
View 1 Replies View RelatedI have 2 WLC (5508), i configured the option for enable the high availability, but when the 2 WLC is working the mesh network is unstable, when only wlc is working the mesh is fine.
View 3 Replies View RelatedIn our network we use cisco WS-C6509-E (R7000) Backbobe switch. We want to route syslog to log server.But I couldn't do it. How can solve this problem?
View 7 Replies View RelatedI have one questions regarding if C6509 suports "ip tcp path-mtu-discovery" ? apply this command to GRE interface on C6509?
if yes, let me know what is the the IOS for that.