I've 4500 Core Switch with 4507R chassis, Sup V-10GE(WS-X4516-10GE) along with 2 WS-X4306-GB line Cards, but now I require a line card for 14 more fiber up links and I cannot go with 3 of 4306 as there are only 2 slots left. I've checked and found that E series line cards does not work with Sup V Engine.
As per the link below, I found that "WS-X4448-GB-SFP" is compatible..
[ URL]
Is it possible to use a 10GE interface on a sup720 and an interface from a 671610GE line card and create a port channel. I haven't found specific documentation on CCO stating you can. I have found the QOS queuing is differnet between the sup and line card.
View 1 Replies View RelatedIs it possible that catalyst 4500 Supervisor Engine V-10GE WS-X4516-10GE works with WS-X4612-SFP-E?I know suprtvisor engine V-10GE is not support E-serious linecard, but when I use the configuration tool, I can choose these two products together. Is it a bug?I need novell IPX in this case, I find supervisor 6E & 7E are already not support, so I have no choice to choose V-10GE.
View 1 Replies View RelatedWe have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
we have Supervisor Engine 720 10GE (VS-S720-10G) in slot 5 on Catalyst 6509-E. Slot 6 is free. We need to replace VS-S720-10G. Is it possible the following scenario
1. we will insert new VS-S720-10G into the slot 6
2. then we will remove the faulty VS-S720-10G from the slot 5
Will everything work without interuptions. Is any document where I can find step-by-step procedure how to replace VS-S720-10G ?
I am getting conflicting info about this, and need to get confirmations.Is the older 6513 (non E) model compatible with WS-X6407-10GE blade?The switch we're getting this for have WS-SUP720-3B, 6000W power supply, and WS-C6K-13SLT-FAN2.From what I read they are compatible if entered in slot 9-13, but I also heard that 10GE modules are not compatible with the non E chassis.
View 1 Replies View RelatedI have supervisor engine ws-x4516 with two line card WS-X4424 - GB - RJ45 - 1No ,WS-X4548 - GB - RJ45 - 1No. Now i want switch and hardware redundancy.
View 3 Replies View RelatedI will be adding two WS-X6716-10GE cards in a CAT6509 soon, and will create 4 port channels with 3 ports each in the new cards, but I do have a few questions:
1 - I will be adding cards in slots 3 and 8, can I mix and bundle ports from both modules into a single etherchannel, I mean, like two ports in slot 3 and 1 port in slot 8 to create a PortChannel ?! Or can I only bundle ports in the same card/port-group in a Etherchannel using this WS-X6716-10GE card?
2 - Do I need to issue the hw-module slot x oversubscription port-group y command in order to be able to bundle ports in the Etherchannel I need to create ?! I will be using 4 Etherchannels (LACP) with 3 ports each, running in trunk mode. So I guess, I will be using something like:
int tengig 3/1
switchport mode trunk
switchport trunk encapsulation dot1q
logging event link-status
[Code] ....
I wanted to know that in nexus 7009, can i use mix of F2/M1/M2 series line cards ? will they work with each other ? Lets say i have F2 line card and M2 line card, will servers attached to them will communicate with each other ?
View 4 Replies View RelatedI urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies View RelatedCisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
when replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?
View 2 Replies View Relateddirect me to a document detailing the order that line cards are supposed to boot in a 6500? I'm noticing random boot sequences in some of my chassis,?Note: We currently run Sup720 3CXL for the most part.
View 6 Replies View RelatedThe WS-X68xx series line card has a fabric of 40Gbps and a 16 Port 10GE has a 4:1 oversubscription rate. The WS-X6908-10G has a fabric speed of 80Gbps and has a 1:1 oversubscription rate.
If I mixed the 68xx and 69xx series line card, do I get 80Gbps for the 6900x and 40gbps for the 68xx line card? Or would the 69xx series line card be downgraded to 40Gbps?
From my understanding, the 68xx series has a DFC card and thus the fabric speed operates independently.
We currently have a WS-C6506 chassis with a line-card WS-X6408A-GBIC. Currently we need to replace the chassis by a Ws-6504-E and also the line-card. My question is: What must buy line-card and meets the same specifications of WS-X6408A-GBIC?.
View 4 Replies View RelatedWe are planning to replace a few line cards in the existing 6509-E chassis. The sup installed is a VS-S720-10G-3C but the line cards are legacy. As a result we are not able to enable the VSS functionality. We are looking to replace the existing line cards with the following:
1. 1 x WS-X6716-10G-3C
2. 1 x WS-X6724-SFP
3. 4 x WS-X6724-GE-TX
What are the requirements in terms of IOS and Roman.
The current IOS is: Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
And the ROM Version is: ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
Do I need an upgrade?
Cisco announced EOL for ws-x6148A-GE-45AF line card and proposed WS-X6148E-GE-45AT. However this card seems not to be supported by the SUP2T-10G supervisor. Which alternative card should I take for this EOL line card, or can I use the proposed line card (use extra daughter card DFC4)?
I'm looking for an alternative line card for the 650x-E chassis with Supervisor 2T iso 6148-GE-45AF
I have a LAP-1142 connected to one of our PoE blade in our 4506 switch, it used to work fine with the following power consumption:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3 auto on 21.5 20.0 AIR-AP1252AG-A-K9 3
However, we had power issue on Apr 28, so it failed and we saw from the log below:
Apr 28 13:57:38.990: %C4K_ETHPORTMAN-3-INLINEPOWEROVERDRAWN: Inline powered device connected on port Gi4/3 exceeded its hardware protection threshold.Apr 28 13:57:39.694: %PM-4-ERR_DISABLE: inline-power error detected on Gi4/3, putting Gi4/3 in err-disable state After the power restored later, the other LAP connecting with the same blade restored without any problem, except this one:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3 auto on 16.6 15.4 Ieee PD 3
On a number of 6500 chassis it appears that linecard 3 did exist at somepoint, but was removed.Problem is that when issuing the 'show int desc' or 'show ip int brie' the ports for the still appear, and indeed same with 'show run' and 'show conf'.
View 1 Replies View RelatedI need to pull a WS-X4712-SFP+E line card from an online 4507 chassis, can this be done, or does it need to be offline?
View 2 Replies View RelatedI am writing with regard to a high memory utilization that we have on a pair of line card WS-X6748-GE-TX and WS-X6724-SFP for a VSS 6500. I am enclosing a little part of the "show tech"of this VSS 6500 where is possible to see the high memory utilization of the line cards 1/1, 1/2, 2/1, and 2/2, in despite of having some ports in state connected. In addition of this, the IOS installed on VSS 6500 is s72033-ipservicesk9_wan-vz.122-33.SXI6.bin for checking if there are some bugs affecting the behaviour of the Switch for this case.
System Resources
PFC operating mode: PFC3C
Supervisor redundancy mode: administratively sso, operationally sso
Switching resources: Sw/Mod Part number Series CEF mode
1/1 WS-X6748-GE-TX CEF720 CEF
1/2 WS-X6724-SFP CEF720 CEF
[code]....
I was trying to upload image to sup x4516 V10G from Rommon using the management port but did not succeed. The steps which I did as mentioned below: [code]I got the tftp request on the tftp server but from the switch was showing access violation
View 0 Replies View RelatedDoes Nexus 7K support Multiple VDCs sharing ports on a single line card. One of our cisco parnter engineers stated that cisco doenst recommend using same line card for multiple VDCs.The second VDC (Non-Default VDC) will be used four our Outside, and DMZ Segment, and to phyiscally segregate our Firewall from our Internal/Inside Core Switch without using a physical DMZ Switch.I know Cisco used the Nexus in this way in their PCI DSS 2.0 Compliance Document. Module is N7K-M148GT-11L
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 10/100/1000 Mbps Ethernet XL Mod N7K-M148GT-11L
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 10/100/1000 Mbps Ethernet XL Mod N7K-M148GT-11L
I was looking at the data sheet for the VS-S2T-10G and there was no compatibility mentioned with the WS-X6708-10GE module.Is this module compatible with this new supervisor?
View 2 Replies View RelatedIs Enhanced FlexWAN module compatible with 7603-S with RSP720-10GE?We have a PA-POS-2OC3 on a 7200 router and we want to use it on 7603-S.
View 1 Replies View RelatedHow to confirm if a 10Ge interface can be set down to 1Ge if required ?
View 4 Replies View RelatedWe had to transport one of our 4948 10 GE to another Data Centre and when we got it there and tried to power up its System Status LED was red and we cannot even get console to the device.
We can try to see if the switch is completely dead and needs replacing or is there something we can do to get it back up and running again?
I am in front of a choice what to select to deploy 10Ge in my datacenter to get four 6504e and two 3750x units connected to each other.All devices are located in 3-7 meters away from each other.The choice is whether to go for a multimode fiber and 10GBASE-SR X2 Modules OR cat7 UTP and 10GBASE-T X2 pluggable transceiver.Money wise it doesn't matter.Fiber looks less attractive since it's fragile and a bit harder to put in underfloor area.Cat7 is more attractive but there are 2 points:
1) I couldn't find ANY single photo of a 10GBASE-T (a module with a single RJ45 port). How does it look? Does it come with a cable or...??
2) How stable is it to run 10Ge over UTP?
I have a two Cisco 4510R each with two sup V-10GE redundant. The code on these sup modules are 12.2(31r)SG3. I need some assistance in getting this setup worked out. I have all four of the 10GE populated with appropriate optics. I setup a link from one 4510R to the other using these interfaces. From the documentation I found I had to use Tengi1/1 and Tengi2/2 as the redundant pair. I plugged the up link into these ports. The Tengi1/1 (active supervisor) links up and works fine. But when I look at the ports port Tengi2/2 it isn't showing link or active. Now port 2/1 (nothing plugged into it) is showing as active.
Now is the redundancy supposed to be 1/1 and 2/1? If so, the switch is in production, when I move the connection over from 2/2 to 2/1 will it cause a outage? The reason for this is I now have a system with a 10G port and would like to utilize one of the other 10G ports. Is that possible? Or does it have to be a lag/redundant up link to work (say to another switch)?
What does RP drops entail? We are experiencing 0.23 % drops on an vlan int on one of our 6500. This interface is an L3 to a server-subnet. Doing a sh int vlan 238 switching shows 30935411 RP (Route Processing) drops.It was a bit unclear to me in the thread "Input queue drops on 6500 vlan interface" if RP drops was through the router, or to the router(mgmnt)?I can do a netdr to see what traffic goes to it. It should not generate CPU load, but I think I will wait until after hours before I try that command.
- do NETDR:
-- debug netdr cap rx vlan 238
-- show netdr cap
We have two 3750 stackable switches in core layer.
1. We are planning to stack two 3750 for greater bandwidth to use
2. We could configure 10GE link (by Network module) between these two switches
which solution provides increased bandwidth and redundancy?
I am trying to configure a 6509 as the passive receiver from a Dell Force10 10Ge switch with 2 sfp to 2 gig ports on our 6509 switch, I see LACP is up on both sides but cannot pass traffic, I have only 2 vlans that will carry across the aggregate link from our vmware boxes, this is just a temp until I get a 10ge in our 6509 chassis.
View 2 Replies View RelatedI am looking for 10 GE copper 24 ports switch. After any time I come N2K-C2232TM-10GE. However, this switch is fabric extender and it is used with Nexus 5K series switches.
My question is Can I use this Nexus 2K standalone as other L2 switches?