I was looking at the data sheet for the VS-S2T-10G and there was no compatibility mentioned with the WS-X6708-10GE module.Is this module compatible with this new supervisor?
View 2 RepliesIs Enhanced FlexWAN module compatible with 7603-S with RSP720-10GE?We have a PA-POS-2OC3 on a 7200 router and we want to use it on 7603-S.
View 1 Replies View RelatedConnected server on a tenGigabitEthernet interface simple configuration setup
switchport
switchport access vlan 201
end
for server connection. Connected with Fibre. The interface is up and up but cannot ping server?
I want to connect WS-C2960S-48TD-L switch to WS-X6708-10G-3CXL module in Cisco WS-C6503-E switch. WS-X6708-10G-3CXL is C6K 8 port 10 Gigabit Ethernet module with DFC3CXL which requires X2 module. on the otherhand, WS-C2960S-48TD-L requires SFP+. Now is it possible to interconnect these two switch interfaces if I use LIU in between. or does WS-X6708-10G-3CXL module supports CVR-X2-SFP+ to use SFP+ transceivers.
View 2 Replies View RelatedI am getting conflicting info about this, and need to get confirmations.Is the older 6513 (non E) model compatible with WS-X6407-10GE blade?The switch we're getting this for have WS-SUP720-3B, 6000W power supply, and WS-C6K-13SLT-FAN2.From what I read they are compatible if entered in slot 9-13, but I also heard that 10GE modules are not compatible with the non E chassis.
View 1 Replies View RelatedI've 4500 Core Switch with 4507R chassis, Sup V-10GE(WS-X4516-10GE) along with 2 WS-X4306-GB line Cards, but now I require a line card for 14 more fiber up links and I cannot go with 3 of 4306 as there are only 2 slots left. I've checked and found that E series line cards does not work with Sup V Engine.
As per the link below, I found that "WS-X4448-GB-SFP" is compatible..
[ URL]
After inserting a RSP720-3C-10GE in module 6 and running the show module command display the following [code]what is the meaning of the UnKnown on the oline diag status ?
View 1 Replies View RelatedWhen i swapped a Sup v 10 ge for a Sup6 E Tonight in order to take advantage of the netflow capabilites of the Sup V - It came up with module unsupported for the following cards - WS-X4648-RJ45V-E Will these only work with the Sup6 E or what
View 2 Replies View RelatedWe recently installed a WS-X6716-10GE module in slot 6 within a Cisco 6506. We are using two ports on the module (6/13 and 6/14), which are port channeled together to a Nexus 5548. Everything has been running fine for about a month and the card had a green light but the ports stopped communicating. The module was screwed into the chassis/slot. For problem determination reasons, we reconfigured ports 6/13 & 6/14 to 6/15 & 6/16 and moved the cables but the module was still not responding. We eventually pulled the module out of the slot and reinserted the module back into the slot, which reset the module and fixed the problem. Is there any way to determine if this was hardware problem with the module and it should be replaced, or is it a software bug/problem? We opened up a ticket with the TAC but we haven't heard back from them yet.
Cisco WS-C6506-E
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXI8, RELEASE SOFTWARE (fc2)
Mod Ports Card Type Model
--- ----- -------------------------------------- ------------------
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B
6 16 CEF720 16 port 10GE WS-X6716-10GE
[code]....
We have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in WS-X6704-10GE module on both sides. When you shut down the port on one side the other port still stays as up and you need phisycally to unplug the cable to have it down. The same behaviour is seen no matter on which of the two switches you shut down the port, the opposite one always stays as up and only removal of the cable makes it go down.
The ports are configured quite simply:
interface TenGigabitEthernet1/1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
no ip address
udld port
The IOS version is 12.2(18)SXF8
I am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
I want to know which of these Bluetooth module is compatible with Dell Latitude D630: 360, 365, 370, 375, 380.
View 1 Replies View RelatedWe have a core switch with the following ios and supervisor engine. Can we add a16 port LR (x2)or LRM(X2) ON the core switch?if not what modifications has to be done?if an ios upgrade is necessary is it a costly affair?At present we have two 1gb up link modules in single and multimode fiber .
#sh moduleMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL0803T308 2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAD07500600 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1439UMZK
#sh versionCisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-M), Version 12.2(33)SXI4a, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 16-Jul-10 19:51 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1) uptime is 1 year, 27 weeks, 4 days, 23 hours, 30 minutesUptime for this control processor is 1 year, 27 weeks, 4 days, 22 hours, 58 minutes(code)
My client is going to deploy 10GE and they will purchase new modules and add them to Cisco 7604/7609 platform.
Should I propose 7600-ES+4TG3C or WS-X6704-10GE?? What are the main differences between those two modules? Or what's the determining factor(s)?
We currently have Cisco WS-X6708-10GE blade installed in our Cisco 7606-S switch. Each of the ports have a X2-10GB-SR tranciever. When I look at the port with the "sh int tengig xx" command I see the following:
!
TenGigabitEthernet 4/1 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c.b0ca.75c0
!
TenGigabitEthernet 4/2 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c..b0ca.75c0(code)
we can't start WS-X6708-10G-3CXL on WS-C6506-E. [code] we did try on conf t mode "power enable module 3" and it didn't work. [code]
View 2 Replies View RelatedI currently have a VSS setup on 2 6509-E using 2x VS-S720-10G.Today I tried to install 2x X6708-10G-3CXL, one into each chassis. The first log message I got was that fan tray was going into high-speed mode, is this correct?I then installed the second card in the 2nd chassis and it killed my VSS and proceed to reload the switches. it now also appears to have killed one of my WS-X6724-SFP cards, as it no-longer boots and I get the following errors:
000249: Jan 8 12:52:34.201 GMT: %DIAG-SW1_SP-3-MAJOR: Switch 1 Module 1: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results.000250: Jan 8 12:52:34.205 GMT: %CONST_DIAG-SW1_SP-3-BOOTUP_TEST_FAIL: Switch 1 Module 1: TestLoopback
Also I can't read any of the log files in 'bootflash diaginfo' as it says the file doesn't exist.Everytime I know re-insert the WS-X6724-SFP cards it kills the VSS
I would like to know if we can use the following card i.e. WS-X6704-10GE along with SUP-2T which will be configured in VSS.
This line is supported with SUP-2T, however not sure if the sup 2t will be configured in VSS. If any supporting document can be provided for the same , that would be great.
If this is supported than whether i would be getting line rate/non blocking capacity with WS-X6704-10GE. Since SUP-2T provides 80 Gbps bandwidth per slot.
The difference between the link terms 10G & 10GE?
View 1 Replies View RelatedMy customer has upgrade his 4506 from 6L-E to 7L-E 10GE.Ever since then if he run the command show dot1x interface gigabitEthernet x/x details some information are not been displayed (below are missing information)Is this intensional or do I need to kick this to TAC?
View 1 Replies View RelatedHow to confirm if a 10Ge interface can be set down to 1Ge if required ?
View 4 Replies View RelatedWe had to transport one of our 4948 10 GE to another Data Centre and when we got it there and tried to power up its System Status LED was red and we cannot even get console to the device.
We can try to see if the switch is completely dead and needs replacing or is there something we can do to get it back up and running again?
I am in front of a choice what to select to deploy 10Ge in my datacenter to get four 6504e and two 3750x units connected to each other.All devices are located in 3-7 meters away from each other.The choice is whether to go for a multimode fiber and 10GBASE-SR X2 Modules OR cat7 UTP and 10GBASE-T X2 pluggable transceiver.Money wise it doesn't matter.Fiber looks less attractive since it's fragile and a bit harder to put in underfloor area.Cat7 is more attractive but there are 2 points:
1) I couldn't find ANY single photo of a 10GBASE-T (a module with a single RJ45 port). How does it look? Does it come with a cable or...??
2) How stable is it to run 10Ge over UTP?
I have a pair of 5585X-SSP20's which is working in active/standby multi context mode. The code is 8.2(5) and i have the ASA5585-SSP-20 VPN Premium license.
I am planning to utilize the 10G interfaces. Is it possible to have a single license for 10GE I/O and share it between the two chassis in ver8.2(5)
I have a two Cisco 4510R each with two sup V-10GE redundant. The code on these sup modules are 12.2(31r)SG3. I need some assistance in getting this setup worked out. I have all four of the 10GE populated with appropriate optics. I setup a link from one 4510R to the other using these interfaces. From the documentation I found I had to use Tengi1/1 and Tengi2/2 as the redundant pair. I plugged the up link into these ports. The Tengi1/1 (active supervisor) links up and works fine. But when I look at the ports port Tengi2/2 it isn't showing link or active. Now port 2/1 (nothing plugged into it) is showing as active.
Now is the redundancy supposed to be 1/1 and 2/1? If so, the switch is in production, when I move the connection over from 2/2 to 2/1 will it cause a outage? The reason for this is I now have a system with a 10G port and would like to utilize one of the other 10G ports. Is that possible? Or does it have to be a lag/redundant up link to work (say to another switch)?
We have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
i was checking the datasheet of 500X series and got confused regarding the 10GE uplinks. how many 10GE ports can be used for uplink and which transceiver should be used for 10GE copper uplink? for example, SG500x-24 switch has 24GE ports and 4x10GE uplinks. can i use the 4x10GE ports for uplinks or only 2 ports are for uplink and the rest for stacking?
View 6 Replies View RelatedWhat does RP drops entail? We are experiencing 0.23 % drops on an vlan int on one of our 6500. This interface is an L3 to a server-subnet. Doing a sh int vlan 238 switching shows 30935411 RP (Route Processing) drops.It was a bit unclear to me in the thread "Input queue drops on 6500 vlan interface" if RP drops was through the router, or to the router(mgmnt)?I can do a netdr to see what traffic goes to it. It should not generate CPU load, but I think I will wait until after hours before I try that command.
- do NETDR:
-- debug netdr cap rx vlan 238
-- show netdr cap
We have two 3750 stackable switches in core layer.
1. We are planning to stack two 3750 for greater bandwidth to use
2. We could configure 10GE link (by Network module) between these two switches
which solution provides increased bandwidth and redundancy?
I am trying to configure a 6509 as the passive receiver from a Dell Force10 10Ge switch with 2 sfp to 2 gig ports on our 6509 switch, I see LACP is up on both sides but cannot pass traffic, I have only 2 vlans that will carry across the aggregate link from our vmware boxes, this is just a temp until I get a 10ge in our 6509 chassis.
View 2 Replies View Relatedi have a Cisco 7609 with ws-6704-10ge, trying to test a cable that is connected to the 10Gig interface , i connected the other end to a 1Gig GBIC interface on WS-X6516-GBIC, now the speed does not match but how to force the 10Gig interface speed to 1Gig, will that ever work? both has LX optics and the cable is SM
View 2 Replies View RelatedI am looking for 10 GE copper 24 ports switch. After any time I come N2K-C2232TM-10GE. However, this switch is fabric extender and it is used with Nexus 5K series switches.
My question is Can I use this Nexus 2K standalone as other L2 switches?
We have CORE switch model : Cisco WS-C4510R-E with dual SUP 5 - 2 10GE. [code] Now We want to upgrade this IOS to the upgraded version.
View 3 Replies View Related