My client is going to deploy 10GE and they will purchase new modules and add them to Cisco 7604/7609 platform.
Should I propose 7600-ES+4TG3C or WS-X6704-10GE?? What are the main differences between those two modules? Or what's the determining factor(s)?
we can't start WS-X6708-10G-3CXL on WS-C6506-E. [code] we did try on conf t mode "power enable module 3" and it didn't work. [code]
View 2 Replies View RelatedI currently have a VSS setup on 2 6509-E using 2x VS-S720-10G.Today I tried to install 2x X6708-10G-3CXL, one into each chassis. The first log message I got was that fan tray was going into high-speed mode, is this correct?I then installed the second card in the 2nd chassis and it killed my VSS and proceed to reload the switches. it now also appears to have killed one of my WS-X6724-SFP cards, as it no-longer boots and I get the following errors:
000249: Jan 8 12:52:34.201 GMT: %DIAG-SW1_SP-3-MAJOR: Switch 1 Module 1: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results.000250: Jan 8 12:52:34.205 GMT: %CONST_DIAG-SW1_SP-3-BOOTUP_TEST_FAIL: Switch 1 Module 1: TestLoopback
Also I can't read any of the log files in 'bootflash diaginfo' as it says the file doesn't exist.Everytime I know re-insert the WS-X6724-SFP cards it kills the VSS
I want to connect WS-C2960S-48TD-L switch to WS-X6708-10G-3CXL module in Cisco WS-C6503-E switch. WS-X6708-10G-3CXL is C6K 8 port 10 Gigabit Ethernet module with DFC3CXL which requires X2 module. on the otherhand, WS-C2960S-48TD-L requires SFP+. Now is it possible to interconnect these two switch interfaces if I use LIU in between. or does WS-X6708-10G-3CXL module supports CVR-X2-SFP+ to use SFP+ transceivers.
View 2 Replies View RelatedWe are looking for buying a 20GE port 7600 ES+ Card. However, there are a few different models, we are not sure which one is the right one. We will be using this card for Metro Ethernet Termination, MPLS VPN, EoMPLS, QoS (Marking, CBWFQ), PPPoE, possibly VPLS.
View 5 Replies View RelatedI was looking at the data sheet for the VS-S2T-10G and there was no compatibility mentioned with the WS-X6708-10GE module.Is this module compatible with this new supervisor?
View 2 Replies View RelatedWe currently have Cisco WS-X6708-10GE blade installed in our Cisco 7606-S switch. Each of the ports have a X2-10GB-SR tranciever. When I look at the port with the "sh int tengig xx" command I see the following:
!
TenGigabitEthernet 4/1 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c.b0ca.75c0
!
TenGigabitEthernet 4/2 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c..b0ca.75c0(code)
Connected server on a tenGigabitEthernet interface simple configuration setup
switchport
switchport access vlan 201
end
for server connection. Connected with Fibre. The interface is up and up but cannot ping server?
i have a query ,we are planning to upgrade the Sup Engine from WS-SUP720-3B 2 ports Supervisor Engine 720 to
RSP720-3CXL-GE=
Cisco 7600 Route Switch Processor 720Gbps fabric,PFC3CXL, GE
Can we use the same old IOS from Sup720 to the New RSP720 without purchasing it ?
Show Version-- Cisco Router 7609
Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB3, RELEASE SOFTWARE (fc1)ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
System returned to ROM by power cycle at 08:36:39 PDT Fri Mar 30 2007 (SP by power on)
System restarted at 10:04:20 GMT Fri Nov 25 2011
System image file is "bootdisk:c7600s72033-advipservicesk9-mz.122-33.SRB3.bin"
Last reload type: Normal Reload
[code]....
what is use of haiving SPA and SIP in router hardware ? what if we dont have them in router ?
View 3 Replies View RelatedI need to know if upgrading Cisco IOS on 7600 series router is possible. From 12.2(18)SXF --> 12.2(33)SRC, i need this because SRC supports Lawfull Intercept.
specification of router is 7606
slot 1 - WS-X6708-10GE
slot 1/0 - WS-F6700-DFC3C
slot 4 - WS-X6408A-GBIC
slot 6 - WS-SUP720-3B
slot 6/0 - WS-F6K-PFC3B
slot 6/1 - WS-SUP720
The 7600 platform support x.25 and XOT features. In ios versión S764AEK9-15103SCisco 7600-RSP720 IOS ADVANCED ENTERPRISE SERVICES SSH The feature navigator display that support this features, but i'dont see these on the other newer ios version. If posible use 7600 for x.25 / xot or maybe will used de 3900 platform?
View 1 Replies View RelatedIf I have SIP-200 and I need to configure a feature , for eg - PPP on SIP-200 , is it something possible ? If Yes how I can do that in IOS ?
View 1 Replies View RelatedToday i want to ask is cisco 7600 support ip next-hop recusrive x.x.x.x (PBR feature).
View 1 Replies View RelatedWhy below simple PBR is not implemented in H/W knowing the Copp is not configured
NPE-1#sh ver | i image
System image file is "bootdisk:c7600rsp72043-advipservices-mz.122-33.SRE0a"
NPE-1#sh run int GigabitEthernet1/1
interface GigabitEthernet1/1
ip address 11.0.0.1 255.255.255.0
ip pim sparse-mode
[code]...
I am trying to establish a BGP session between a Cisco 7600 and Juniper MX960, but this always stucks in OpenConfirm state.
access-4#show ip bgp v v VRF1 neighbors 166.63.168.197BGP neighbor is 166.63.168.197, vrf VRF1, remote AS 5555, local AS 65533, external link BGP version 4, remote router ID 195.2.1.21 BGP state = OpenConfirm Last read 00:02:27, last write 00:02:27, hold time is 180, keepalive interval is 60 seconds Message statistics: InQ depth is 0 OutQ depth is 0 Sent Rcvd Opens: 4 4 Notifications: 2 1 Updates: 0 0 Keepalives: 4
May 12 13:58:07.531 bst: TCP src=54912, dst=179, seq=1766275951, ack=1681278050, win=17520 ACK PSHMay 12 13:58:07.535 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:53.883 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:59.359 bst: IP: s=166.63.168.197 (Vlan20), d=166.63.168.198, len 61, rcvd 2May 12 13:58:59.359 bst: TCP src=54912, dst=179, seq=1766276010, ack=1681278050, win=17520 ACK PSH FINMay 12 13:58:59.359 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:59.359 bst: %BGP-3-NOTIFICATION: received from neighbor 166.63.168.197 4/0 (hold time expired) 0 bytes
ICMP works fine. It is same on JUniper end. Sending keepalives but cannot receive
###interface configinterface Vlan20 ip vrf forwarding VRF1 ip address 166.63.168.198 255.255.255.252 no ip redirects no ip proxy-arp load-interval 30end
###bgp config
neighbor 166.63.168.197 remote-as 5555 neighbor 166.63.168.197 local-as 65533 neighbor 166.63.168.197 ebgp-multihop 5 neighbor 166.63.168.197 update-source Vlan20 neighbor 166.63.168.197 activate neighbor 166.63.168.197 soft-reconfiguration inbound
I am pretty far out of my comfort zone here but these VS-S720-10G-3C cards were purchased to upgrade our 7609/7606 routers, the spec sheet says they are compatable but I can't find an IOS that "likes" them. I had no problem finding an IOS and using the vss cards in our 6506...
[URL]
what is the use SPA and SIP...in router hardware ? What if we do not have them ?
View 1 Replies View RelatedI have a strange QoS problem with one Cisco7600 (sup7203BXL, IOS 12.2(33)SRE6).
This is layer 2 traffic,and all ports are L2 dot1q trunks:
1) Packet comes with DSCP 46 on Gigabit port (WS6728-SFP) with "mls qos trust dscp" configured. It goes out the port of the same card/slot with DSCP 0.
2) packet comes with DSCP 46 on different Gigabit port on the same card/slot with "mls qos trust dscp" and also "mls qos vlan-based" configured. It qoes out out the port with DSCP 46.
Why the switch behave differently if "mls qos vlan-based" is configured on port (or to say it works correct since it doesn't override DSCP)?
I have global command "mls qos rewrite ip dscp" since this 7600 is also MPLS PE router and I found in documentation that "mls qos rewite ip dscp" is mandatory for QoS on MPLS (EXP bits). So I can't turn off "rewrite ip dscp". Again the problem that I presents is L2 problem not MPLS (MPLS is used for different traffic).
Also mls qos mappings are ok COS to DSCp are 5 to 46 and vice versa.
Furthermore, as far as I know if I have configured "mls qos trust dscp" on Gigabit ethernet port, switch (7600) should work in this order:
- make internal DSCP from packet DSCP
- since I don't have configured DSCP mutation DSCP should stay the same (46)
- using map DSCP - COS ( 46 -5 ) switch will choose queue on outgoing interface in regards to mapped COS
I'm looking for iformation if CFM Local Maintenance End Point configured on Cisco 7606 router is able to respond to the Y.1731 Performance Monitoring (DMM/DMR ).I know I can use IP SLA to configure Y.1731 PM measurements, but I just need a reflector that will answer for incoming DMM messages with DMRs.
View 0 Replies View RelatedYou can configure EoMPLS on a port of the WS-X6724SFP card found in a Cisco 7600 with Supervisor 720.
View 1 Replies View Relatedif the 7600-SIP-200 supported in VSS mode or not ?
I have configured to Cisco Catalyst 6513 as VSS, both of them have the 7600-SIP-200 module, before converting them to VSS I was able to work with the 7600-SIP-200 module, but after I did convert them to VSS, both modules didn't work.
here is the show module output, after VSS conversion:
VSS1#show module Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAE14500GMT 7 5 Supervisor Engine 720 10GE
[Code].....
Need to clarify this log message:
*Oct 23 06:20:07 UTC: %FPD_MGMT-3-INCOMP_IMG_VER: Incompatible ROMMON (FPD ID=5) image version detected for 7600-SIP-200 card in slot Detected version = 1.3, minimum required version = 1.4. Current HW version = 2.303.
I would like more information of performance to 7600 router with the SP-720, how many sessions full bgp routing it supports? I have 4 links 1 GB and a throughput of 900 MB.
View 4 Replies View RelatedI have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?
View 1 Replies View RelatedI have a 7606 running c7600rsp72043-advipservicesk9-mz.122-33.SRD2.bin with SIP-400 card that has suddenly stopped working, on checking the logs i see the following:
%ONLINE-SP-6-TIMER: Module 3, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 3 set off (Module Failed SCP dnld)
I have tried reseating and even moving it to a different slot but no luck.
%ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 4 set off (Module Failed SCP dnld)
sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 20 ESM20G 7600-ES20-GE3C JAE1237UT90
2 4 7600 ES+ 7600-ES+4TG3CXL JAE13157HIW
3 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE13219CZH
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE JAE1151819I
6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE JAE11495POH
[code].....
im having lms 4.2.2 and monitoring a cisco 7600 router interface ten gigabit ethernet x/x under dfm. When ever the interface is down due to any media issue i am not getting any alerts in dfm., the interface used to go down for more than 10 minutes. I am able to do an snmpwalk to this interface when the interface was down and getting the value as 2(for down). I am getting other information and configuration mode alerts in dfm for this device.
View 1 Replies View RelatedI posted also under Service Providers for my problem with MPLS/VPN. I just noticed I have the same issue with plain IPV4 BGP. [URL] I have two 7600 running on SRC3 and SRD6. Both acting as RRs.
I noticed that RR1 is reflecting the route to this other 7600 iBGP peer but not installing/importing the route. Other iBGP speakers are able to install and import the route. Is there any issue with 7600 SRC/SRD IOS for Route-reflection?
iBGP policy is similar to all but only the 7600 is unable to install the route. Other 7200 ibgp peers are successful.
Router with 2 RSP RSP720-3C-GE & Image: c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin We are getting the message as
------------------ show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
Show log is attached & we are getting %DHCPD-4-DECLINE_CONFLICT: messages constantly.
I'm trying to find a single device that can both handle Q-in-Q VLAN trunk termination and also TDM cross connects between DS0's on a multi-channel T1 card and DS0's on a multi-channel DS-3 card. I'm looking at a Cisco 7606-S with SUP720's. If I install a 7600-SIP-200 or 7600-SIP-400 with both a SPA-2XCT3/DS0 (channelized T3 card) and a SPA-8XCHT1/E1 (channelized T1 card) will I be able to TDM cross connect the DS0's between the cards? Is there a limit on the number of TDM cross connects? Also, I noticed the CMM cards are EOL. Ideally we'd like to terminate PRI's into the 7606 and run H.323. We'd like to pass voice calls to CUCM and TDM switch FAX calls (via H.323 dial-peer) to a given CAS DS0 on the SPA-2XCT3/DS0. Is this doable with any of the current cards? If not, then we'll stick to the configuration in the first paragraph and only have the 7606 handle the TDM cross connects.
View 3 Replies View RelatedI am looking for the best QoS method for a 7600 series router. We have a 7604 edge router that has remote branch connections to it via GRE tunnels. unfortunately I cannot shape on these GRE tunnels neither can I use bandwidth or priority statements.
View 1 Replies View RelatedI want to do qinq on this card under its sub-interface, unfortanately it doesnt support the command as compared to other ES cards. [code]
View 3 Replies View RelatedWhat are the limitations of Net flow v9 support on the 7600 platform for the SR code releases?
I know that Flexible Net flow is only available on newer releases with some newer hardware. Flexible Net flow gives you the ability to provide full support for Netflow v9 as well as IPFIX.
However, the documentation indicates that Net flow v9 is still supported in the SR code. So I am just trying to find out what are the limitations in how Net flow v9 is implemented without "Flexible Net flow". The Cisco TAC was unable to provide me any documentation about this.