Cisco Switching/Routing :: WS-X6708-10G-3CXL Card Insertion Killed VSS And Fan Tray
Jan 7, 2012
I currently have a VSS setup on 2 6509-E using 2x VS-S720-10G.Today I tried to install 2x X6708-10G-3CXL, one into each chassis. The first log message I got was that fan tray was going into high-speed mode, is this correct?I then installed the second card in the 2nd chassis and it killed my VSS and proceed to reload the switches. it now also appears to have killed one of my WS-X6724-SFP cards, as it no-longer boots and I get the following errors:
000249: Jan 8 12:52:34.201 GMT: %DIAG-SW1_SP-3-MAJOR: Switch 1 Module 1: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results.000250: Jan 8 12:52:34.205 GMT: %CONST_DIAG-SW1_SP-3-BOOTUP_TEST_FAIL: Switch 1 Module 1: TestLoopback
Also I can't read any of the log files in 'bootflash diaginfo' as it says the file doesn't exist.Everytime I know re-insert the WS-X6724-SFP cards it kills the VSS
View 14 Replies
ADVERTISEMENT
Oct 27, 2012
we can't start WS-X6708-10G-3CXL on WS-C6506-E. [code] we did try on conf t mode "power enable module 3" and it didn't work. [code]
View 2 Replies
View Related
Jun 1, 2012
I want to connect WS-C2960S-48TD-L switch to WS-X6708-10G-3CXL module in Cisco WS-C6503-E switch. WS-X6708-10G-3CXL is C6K 8 port 10 Gigabit Ethernet module with DFC3CXL which requires X2 module. on the otherhand, WS-C2960S-48TD-L requires SFP+. Now is it possible to interconnect these two switch interfaces if I use LIU in between. or does WS-X6708-10G-3CXL module supports CVR-X2-SFP+ to use SFP+ transceivers.
View 2 Replies
View Related
Sep 28, 2011
My client is going to deploy 10GE and they will purchase new modules and add them to Cisco 7604/7609 platform.
Should I propose 7600-ES+4TG3C or WS-X6704-10GE?? What are the main differences between those two modules? Or what's the determining factor(s)?
View 2 Replies
View Related
May 8, 2013
I have just buy a 10G card for Cat 6513, these are information: PDCMSFC-1>sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL08373Z37
7 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD08330322
Mod Sub-Module Model Serial Hw Status
--- --------------------------- ------------------ ------------ ------- -------
7 Policy Feature Card 3 WS-F6K-PFC3A SAD083207AL 2.4 Ok
7 MSFC3 Daughterboard WS-SUP720 SAD0832037Y 2.3 Ok
About card: WS-X6716-10G-3C
When I install this card on Cat 6513, has a message: " fan tray no support"
View 5 Replies
View Related
Oct 6, 2011
I need to install a HWIC-2Fe card onto the Cisco 3845 motherboard. Do I need to power down the router for this installation?Also I had a few more queries in regards to 3845 routers.
1) DO C3845 routers support insertion and removal of Network modules while powered on?
2) Do C3845 routers support insertion and removal of Power supply (redundant one)?
3) Is it the case that all Network modules which need to be inserted onto the motherboard require the router to be powered down?
4) If there is a need to replace the Network module from a particular slot with a new one (same make), powering down the router is not required?
View 2 Replies
View Related
Aug 26, 2012
i am not able to connect internet using the sim card port of my dell xps15 model no.-L520X. Can you tell me how to connect through the port.
View 1 Replies
View Related
Jun 2, 2013
We currently have Cisco WS-X6708-10GE blade installed in our Cisco 7606-S switch. Each of the ports have a X2-10GB-SR tranciever. When I look at the port with the "sh int tengig xx" command I see the following:
!
TenGigabitEthernet 4/1 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c.b0ca.75c0
!
TenGigabitEthernet 4/2 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c..b0ca.75c0(code)
View 4 Replies
View Related
Dec 7, 2011
Is it possible to configure the switchports on a 6500 linecard before it has been inserted?
So for example, I have a 6509 with slot 9 free. I'm going to install a 48 port line card. Is it possible to configure those 48 ports before the card is inserted?
View 2 Replies
View Related
Aug 23, 2012
The SuperVisor engine in slot 1 of a Catalyst 6513 needed to be replaced because a hardware defect. The SuperVisor engine in slot 2 is active and running CatOS 8.5. The new SuperVisor engine for slot 1 came with CatOS 6.3 and was not syncronized auromatically after insertion. When the customer enter the command "Show boot" he get the output:
AG-A6513-51> (enable) sh boot
BOOT variable = bootflash:cat6000-sup2k8.8-5-5.bin,1;bootflash:cat6000-sup2k8.7-6-2.bin,1;
[Code].....
View 1 Replies
View Related
May 2, 2012
Connected server on a tenGigabitEthernet interface simple configuration setup
switchport
switchport access vlan 201
end
for server connection. Connected with Fibre. The interface is up and up but cannot ping server?
View 10 Replies
View Related
May 27, 2012
We have a Cisco 4507R switch with sup V. This switch fan tray has partial problem .No light in fan tray. We got another fan tray. Can any one tells me is it hot swappable?
What procedure should I flow without any interruption our live network?
View 4 Replies
View Related
Apr 17, 2012
Anyway, my PC kills my modem in record time every time, but the cable modem is fine with my PS3.Within a few minutes of hooking up the PC the connection dies and must be rebooted to work again on anything (even the PS3). During this time the network shows as unidentified and won't even give access to its status page (192.168.100.1).The PS3 doesn't ever induce this state.I have tinkered with settings, drivers, and even clean installs. The modem has no settings I can alter. PC is WIN 7 and the modem is an advanced DOSCIS 3.0 Linksys/Cisco. ISP is Comcast.
View 2 Replies
View Related
May 3, 2011
I've got a 3845 and a 2821 and I need to add another WAN interface card on each router and wonder if this can be done live while the router is running.
View 2 Replies
View Related
Dec 3, 2011
I was looking at the data sheet for the VS-S2T-10G and there was no compatibility mentioned with the WS-X6708-10GE module.Is this module compatible with this new supervisor?
View 2 Replies
View Related
Mar 13, 2013
we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies
View Related
Mar 15, 2012
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
View 1 Replies
View Related
Apr 4, 2013
Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
View 2 Replies
View Related
Feb 8, 2012
How do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies
View Related
Dec 26, 2011
I have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
View 1 Replies
View Related
Jan 11, 2012
I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies
View Related
Aug 30, 2012
I have a Cisco 1811 with a 4/port Serial Async/Sync (HWIC 4 A/S) and another 2 port A/S serial wic. My router seems to have a problem reading the 4/port card. I did some research and it looks like there shouldn't be a compatibility issue.
View 7 Replies
View Related
Aug 30, 2011
i have a nexus 5k with a l3 card i'm not able to bring online
NX-OS is:5.0(3)N2 (1)
L3 card is:L55D160L3
i inserted L3 module several time with the same resul...if i perform a show module i see the card offline. At the boot switch show an error message:
L3 module is down due to a BTCM down..
View 8 Replies
View Related
Oct 18, 2012
I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies
View Related
Jun 5, 2012
I have a customer that in the past has been using 6506E chassis with Sup32 and the WS-X6196-21AF cards for their closet.With the End of Sale of this combination and the announced End of Sale of the Sup720-3B announced, this kind of pushes the configuration to a Sup 2T.BUT the SUP 2T does not support these low speed high density cards.
Is there a card coming that will address need? Customer generally has had dual sup32's and 3 to 4 cards of the 96port AF.They stock spares besides haveing smartnet on the boxes or moving to a different platform like the 4510R+ or stacks of switches will mess them up.
View 3 Replies
View Related
Jul 14, 2008
what is the best configuration betwen vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200
View 10 Replies
View Related
Dec 28, 2011
I am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies
View Related
Apr 9, 2013
I can't find anywhere whether it is possible to create a vPC domain with 2 Nexus 5548UP switches, where only 1 Nexus 5548UP has a L3 daughter card.
View 3 Replies
View Related
Sep 8, 2011
I will be adding two WS-X6716-10GE cards in a CAT6509 soon, and will create 4 port channels with 3 ports each in the new cards, but I do have a few questions:
1 - I will be adding cards in slots 3 and 8, can I mix and bundle ports from both modules into a single etherchannel, I mean, like two ports in slot 3 and 1 port in slot 8 to create a PortChannel ?! Or can I only bundle ports in the same card/port-group in a Etherchannel using this WS-X6716-10GE card?
2 - Do I need to issue the hw-module slot x oversubscription port-group y command in order to be able to bundle ports in the Etherchannel I need to create ?! I will be using 4 Etherchannels (LACP) with 3 ports each, running in trunk mode. So I guess, I will be using something like:
int tengig 3/1
switchport mode trunk
switchport trunk encapsulation dot1q
logging event link-status
[Code] ....
View 4 Replies
View Related
Jun 30, 2008
Cisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
View 2 Replies
View Related
Jul 24, 2012
Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.
View 1 Replies
View Related
Mar 20, 2012
when replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?
View 2 Replies
View Related
Nov 10, 2011
Need to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies
View Related