Cisco Switching/Routing :: Connect WS-C2960S-48TD-L Switch To WS-X6708-10G-3CXL Module In WS-C6503-E?
Jun 1, 2012
I want to connect WS-C2960S-48TD-L switch to WS-X6708-10G-3CXL module in Cisco WS-C6503-E switch. WS-X6708-10G-3CXL is C6K 8 port 10 Gigabit Ethernet module with DFC3CXL which requires X2 module. on the otherhand, WS-C2960S-48TD-L requires SFP+. Now is it possible to interconnect these two switch interfaces if I use LIU in between. or does WS-X6708-10G-3CXL module supports CVR-X2-SFP+ to use SFP+ transceivers.
View 2 Replies
ADVERTISEMENT
Dec 16, 2012
I have a Cisco WS-C2960S-48TD-L with 12.2(55)SE2.This is a standalone switch, not in stack, and with no order it reboots itself looking for a new master election. On logging i have nothing, but connected with console cable i see the following after 2 minutes of not showing anything:
Waiting for Stack Master Election...
...
The switch reboots and:
...
*Mar 1 00:00:12.289: Read env variable - LICENSE_BOOT_LEVEL =
[URL]
After searching online i have no seeing nothing about disable the feature of the stack so i configure the priority for the "switch 1" to 15 and configure it the switches 2, 3 and 4 to no provision, although this switches don´t exist:
SW_ACCESS(config)#switch 1 priority 15
Changing the Switch Priority of Switch Number 1 to 15
Do you want to continue?[confirm]
New Priority has been set successfully
[URL]
With this new configuration the switch has rebooted again.Why on a standalone switch the stack is rebooting my system?Is it any feature to disable the stack?
View 8 Replies
View Related
Oct 27, 2012
we can't start WS-X6708-10G-3CXL on WS-C6506-E. [code] we did try on conf t mode "power enable module 3" and it didn't work. [code]
View 2 Replies
View Related
Jan 7, 2012
I currently have a VSS setup on 2 6509-E using 2x VS-S720-10G.Today I tried to install 2x X6708-10G-3CXL, one into each chassis. The first log message I got was that fan tray was going into high-speed mode, is this correct?I then installed the second card in the 2nd chassis and it killed my VSS and proceed to reload the switches. it now also appears to have killed one of my WS-X6724-SFP cards, as it no-longer boots and I get the following errors:
000249: Jan 8 12:52:34.201 GMT: %DIAG-SW1_SP-3-MAJOR: Switch 1 Module 1: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results.000250: Jan 8 12:52:34.205 GMT: %CONST_DIAG-SW1_SP-3-BOOTUP_TEST_FAIL: Switch 1 Module 1: TestLoopback
Also I can't read any of the log files in 'bootflash diaginfo' as it says the file doesn't exist.Everytime I know re-insert the WS-X6724-SFP cards it kills the VSS
View 14 Replies
View Related
Sep 28, 2011
My client is going to deploy 10GE and they will purchase new modules and add them to Cisco 7604/7609 platform.
Should I propose 7600-ES+4TG3C or WS-X6704-10GE?? What are the main differences between those two modules? Or what's the determining factor(s)?
View 2 Replies
View Related
Jun 13, 2013
We have several of these WS-C2960S-24PS-L running 12.2(55)SE5 C2960S-universalK9-M and need to upgrade to a better.IOS since we have a sitution where CPU would get to 100% but we have only a few ports connected.Also we have several of WS-C3750-48P running 12.2(55) SE6 C3750-IPBASEK9-M.
View 3 Replies
View Related
Feb 12, 2012
The pinout of poe and poe+ (802.3af) and (803.3at) of these models of Cisco switches?
WS-C2960S-48FPS-L 48 Ethernet 10/100/1000 PoE+ ports; 740W PoE capacityWS-C2960S-48LPS-L 48 Ethernet 10/100/1000 PoE+ ports; 370W PoE capacityWS-C3750-48PS-S 48 Ethernet 10/100 ports with IEEE 802.3af and Cisco prestandard Power
Pin goes where the power for Poe (802.3af) and poe+ (802.3at) for this model Cisco
View 1 Replies
View Related
Jul 24, 2012
I have a got a requirement where a 24 Port Switch should have 4 SFP's and all 4 should be used at a time, So I've chosen " WS-C2960S-24TS-L"
The transeiver should be GLC-LH-SM, so kindly let me no whether I would be able to use all 4 ports at a time or not.
View 2 Replies
View Related
May 6, 2012
Recently I have faced following problem in my office, We have purchased two new Dell Server Power Edge R910 with built-in 10GB FC Network card. Service tag of this two servers are given bellow.
1. 7D94C2S
2. 6D94C2S
You can can Check specification of this two server from dell website{ URL}
We have two CISCO switch and model is given bellow:
Brand: CISCO
Model: WS-C3560E-12SD
We want to connect server to switch through FC cable and both switch have SPF module. But when we connect server to switch, link do not establish even switch and server port light become off.
Then we have tested the following things:
1. Connect server to server through FC cable, it is okay.
2. Connect switch to switch through same FC cable, it is okay.
I don't understand why it is not working.
View 5 Replies
View Related
Jan 24, 2013
I have configured about 20 of these switches now, and notice in the port listings a TE1/1//1 TE1/1/2 and GI1/1/1 GI1/1/2 uplink port. There are only two uplink SFP+ ports. I now have a reason to install with a 1Gb uplink to the Core. I am using a GLC-LH module at each end. I did configure the TE1/1/1 port for the uplink. Does not work though..Do I need to configure the two GI1/1/1 and 1/1/2 ports for uplink, remove the TE configuration for the uplink to work? Using the UNIVERSAL code with a LANBase license.
View 2 Replies
View Related
Jun 12, 2013
After insertion of SFP module in the Switch i have messages bellow and the switch hangs after couple of minutes it restarts
[Code]....
View 10 Replies
View Related
Nov 30, 2010
Does GLC-GE-100FX is supported on the WS-C2960S-24TD-L. I don't see this switch listed under the compatibiilty matrix.URL,But the datasheet for the 2960S says this:"The Cisco Catalyst 2960-S with SFP+ does not support the GLC-FE-100BX, GLC-FE-100FX, or GLC-FE-100LX."But it provides no reference for the GLC-GE-100FX,The easy answer is, no the 2960S-24TD doesn't support it.
View 1 Replies
View Related
Dec 19, 2012
We have the following stack configuration:
Switch Ports Model SW Version SW Image------ ----- ----- ---------- ---------- 1 28 WS-C2960S-24TS-L 12.2(55)SE3 C2960S-UNIVERSALK9-M 2 28 WS-C2960S-24TS-L 12.2(55)SE3 C2960S-UNIVERSALK9-M 3 52 WS-C2960S-48TS-L 12.2(55)SE5 C2960S-UNIVERSALK9-M * 4 52 WS-C2960S-48TS-L 12.2(55)SE5 C2960S-UNIVERSALK9-M
View 5 Replies
View Related
Jun 25, 2012
I am trying to connect a SF200-48 switch via Mini-GBIC MGBLX1 fibre module to a Cisco 3750 switch with a GLC-SX-MM fibre module installed both running a 1000 Mbps. When connected together they do not enable. Are there compatibility restrictions or is it that the Mini-GBIC modules cannot be used to uplink to a LAN?
View 2 Replies
View Related
Dec 3, 2011
I was looking at the data sheet for the VS-S2T-10G and there was no compatibility mentioned with the WS-X6708-10GE module.Is this module compatible with this new supervisor?
View 2 Replies
View Related
Jun 2, 2013
We currently have Cisco WS-X6708-10GE blade installed in our Cisco 7606-S switch. Each of the ports have a X2-10GB-SR tranciever. When I look at the port with the "sh int tengig xx" command I see the following:
!
TenGigabitEthernet 4/1 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c.b0ca.75c0
!
TenGigabitEthernet 4/2 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c..b0ca.75c0(code)
View 4 Replies
View Related
May 2, 2012
My question is about WS-C3750E-48TD-S and WS-C3750E-24TD-S Switches
What are the limitations of the mapping of VLANs on this device? Is it limited by number or by interface? Does the configuration of an interface has spread all interfaces ?
View 1 Replies
View Related
May 2, 2012
Connected server on a tenGigabitEthernet interface simple configuration setup
switchport
switchport access vlan 201
end
for server connection. Connected with Fibre. The interface is up and up but cannot ping server?
View 10 Replies
View Related
Jul 31, 2012
Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies
View Related
Sep 3, 2012
Any doc for installing the a PoE switch module for a 2951? I find alot about the 2951 PoE Power supply but nothing for the switch module.
View 5 Replies
View Related
Apr 28, 2012
We have Communication Media Module (WS-SVC-CMM) mounted on 6513 switch. It went down twice and we brought it up by applying "power enable module".
View 4 Replies
View Related
Sep 18, 2012
I'm trying to set up a 2951 with a 24 port switch module. I want the ports to act similiarly to the ports on an 881 router - where I assign the VLANs on the router and I set the VLANs to the switchport interfaces.I would like to be able to create the VLANs on the router portion of the 2951 and then, enter the switch module and configure the Ports to the VLANs but, how do I logically connect router to the switch? Is it an internal logical interface - meaning how are the VLANs getting from the router to the switch?
View 24 Replies
View Related
Apr 20, 2013
I have two Switches which i need to put in a same stack - WS-C3750E-48TD and WS-C3750G-48TS . Possible to do so and also which IOS to put in both the switches as WS-C3750G-48TS is having lower RAM and flash.Whether can i put following IOS in these switches and connect them in a stack as i have read that IOS -- 15.0.1. SE are compatible with both the switches.
a . c3750e-ipbasek9-mz.150-1.SE.bin in switch - WS-C3750E-48TD
b. c3750-ipbasek9-mz.150-1.SE.bin in switch -- WS-C3750G-48TS
View 8 Replies
View Related
Feb 13, 2012
Is that possible add WS-C3750-48TS-E to ws-c3750e-48td stack?
View 4 Replies
View Related
Feb 21, 2013
I have a problem with Total Output Drops, it's increase and decreases on WS-C3750E-48TD-E.
SWCIACTCT05#sh int gi1/0/47 | i Total output drops:
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 6487344
SWCIACTCT05#sh int gi1/0/47 | i Total output drops:
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 6487344
SWCIACTCT05#sh int gi1/0/47 | i Total output drops:
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 6487344
[code]....
I checked and found two registered bug id: CSCtq86186 / CSCso81660.I would like to know what is the best IOS version to update my switch, IOS 15.0.2 SE2 or 12.2.58 SE2, by the way, my environment is very critical (data center) and the version 15.0.2 SE2 is very recent, but its stable ?In both versions the problem are fixed?
View 3 Replies
View Related
Dec 20, 2012
7x stack WS-C3750E-48TD-E orignal code 12.2.35...i wanted to get it to 15.0.1 so as a test i disconnected top switch (not the master ) and installed via archive download-sw /allow upgrade 15.0.1.tar. and it worked away fine...
so i moved onto the stack, issued the same command, image loaded rebooted and stack hung..Consoled in and switch was unable to boot..looping on trying to load flash. [code]
View 8 Replies
View Related
Mar 6, 2012
We have supplied Cisco Swtch 2960 with gig SFP modules. It is working fine. However, when I do a show inventory it show proper part no. for the switch chassis but for the GLC T module it shows as unspecified in the PID column.
View 1 Replies
View Related
Oct 4, 2012
I have a problem with a newly bought ws-x4548-rj45v+ i've plugged in the module but when i do show modules all , it show as unsupport
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 2 Supervisor IV 1000BaseX (GBIC) WS-X4515 JAE1048GAXQ2 48 10/100/1000BaseT (RJ45) WS-X4448-GB-RJ45 JAB064806WN3 48 10/100/1000BaseT (RJ45) WS-X4448-GB-RJ45 JAB063005DB4 0 Unsupported module WS-X4548-RJ45V+ JAE1545056U
M MAC addresses Hw Fw Sw Status--+--------------------------------+---+------------+----------------+---------1 0007.0e64.f880 to 0007.0e64.f881 5.2 12.2(20r)EW1 12.2(46)SG Ok2 000b.5fa4.da20 to 000b.5fa4.da4f 1.0 Ok3 0009.e844.d760 to 0009.e844.d78f 1.0 Ok4 ccef.4815.9bf0 to ccef.4815.9c1f 2.0 Unsupport
View 2 Replies
View Related
May 23, 2013
My questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies
View Related
May 12, 2013
I have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
View 9 Replies
View Related
Jul 31, 2012
Trying to find some documentation as to whether there are any other steps for inserting this new module in our N7K. We have 2 blades in already and 2 Sups in 5 & 6. I'm assuming its like the 6500s, where we just slide it in and the OS configures the global parms for it and the default VLAN.
View 2 Replies
View Related
Jan 11, 2012
We having a VSS switch (9 slot chasis) with ios "s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI4", slot 7-9 are currently free. We wanted to install WS-X6708-10G-3C module on slot 7. Once we installed the module it didnt come, after waiting for 15-20min again we removed and inserted, but module didnt come up and we could see following logs on the console:
Jan 12 08:57:40.146: %ISSU-SW2_CFC2-3-ERP_AGENT_SEND_MSG: client/entity send failed; error code is timeout
*Jan 12 08:57:40.330: %ISSU-SW2_SPSTBY-3-ERP_AGENT_SEND_MSG: client/entity send failed; error code is timeout
Jan 12 08:57:40.146: %ISSU_ERROR-SW2_CFC2-3-START_NEGO_FAILED: ISSU NTI Client(2040): failed to start negotiation (ISSU_RC_CLIENT_ENTITY_DOES_NOT_EXIST_IN_PEER)
[code]....
Afer some time VSS switch didnt response to console commands and all the users in access switches were not able to reach the gateway (VSS). Then the problem disappeared once we rebooted both the switches in VSS.why the VSS switch become non-responsive?
View 1 Replies
View Related
Apr 16, 2013
can i use any downlink port of the C4500-X switch as uplink without the need of the network module?i need to connect that switch to C6500E backbone without getting the network module, is that OK or i must get the network module?
View 1 Replies
View Related
