Cisco Switching/Routing :: WS-X6708-10G-3CXL Doesn't Work On WS-C6506-E
Oct 27, 2012we can't start WS-X6708-10G-3CXL on WS-C6506-E. [code] we did try on conf t mode "power enable module 3" and it didn't work. [code]
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: WS-X6708-10G-3CXL Card Insertion Killed VSS And Fan Tray
Jan 7, 2012I currently have a VSS setup on 2 6509-E using 2x VS-S720-10G.Today I tried to install 2x X6708-10G-3CXL, one into each chassis. The first log message I got was that fan tray was going into high-speed mode, is this correct?I then installed the second card in the 2nd chassis and it killed my VSS and proceed to reload the switches. it now also appears to have killed one of my WS-X6724-SFP cards, as it no-longer boots and I get the following errors:
000249: Jan 8 12:52:34.201 GMT: %DIAG-SW1_SP-3-MAJOR: Switch 1 Module 1: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results.000250: Jan 8 12:52:34.205 GMT: %CONST_DIAG-SW1_SP-3-BOOTUP_TEST_FAIL: Switch 1 Module 1: TestLoopback
Also I can't read any of the log files in 'bootflash diaginfo' as it says the file doesn't exist.Everytime I know re-insert the WS-X6724-SFP cards it kills the VSS
Cisco Switching/Routing :: Connect WS-C2960S-48TD-L Switch To WS-X6708-10G-3CXL Module In WS-C6503-E?
Jun 1, 2012I want to connect WS-C2960S-48TD-L switch to WS-X6708-10G-3CXL module in Cisco WS-C6503-E switch. WS-X6708-10G-3CXL is C6K 8 port 10 Gigabit Ethernet module with DFC3CXL which requires X2 module. on the otherhand, WS-C2960S-48TD-L requires SFP+. Now is it possible to interconnect these two switch interfaces if I use LIU in between. or does WS-X6708-10G-3CXL module supports CVR-X2-SFP+ to use SFP+ transceivers.
View 2 Replies View RelatedCisco WAN :: Difference Between 7600-ES+4TG3CXL Or WS-X6708-10G-3CXL
Sep 28, 2011My client is going to deploy 10GE and they will purchase new modules and add them to Cisco 7604/7609 platform.
Should I propose 7600-ES+4TG3C or WS-X6704-10GE?? What are the main differences between those two modules? Or what's the determining factor(s)?
Cisco Switching/Routing :: C6506 Module Cannot Be Detected
Dec 3, 2011My C6506 USING ws-sup720-3B, i upgrade the IOS to the latest release of 12.2(33) SXJ1 IOS version. After upgrade and reload the machine got one module cannot be detect..WS-X6416-GE-MT, 16 port 1000mb MTRK ethernet module. The version of this are:
-HW 1.0
-FW 5.3 (1)1
-SW 8.5 (0.46) RFW
Question 1: Any tools available on cisco to check out the hardware/software compabiity feature?
Question 2: Any release note, compability matrix table etc resources.
Cisco Switching/Routing :: C6506-E / TestAclPermit Fail In WS-X6748-SFP?
Dec 7, 2011in my C6506-E installed module WS-X6748-SFP with WS-F6700-DFC3BXL
last time a see errors:
18:42:49: %DIAG-SP-6-TEST_RUNNING: Module 3: Running TestAclPermit{ID=23} ...
18:42:51: %DIAG-SP-3-TEST_FAIL: Module 3: TestAclPermit{ID=23} has failed. Error code = 0x1
23) TestAclPermit -------------------> F
Current bootup diagnostic level: minimal
Module 3:
Overall Diagnostic Result for Module 3 : MINOR ERROR
Diagnostic level at card bootup: minimal
[code]...
Cisco Switching/Routing :: WS-X6708 TenGig Ports
Jun 2, 2013We currently have Cisco WS-X6708-10GE blade installed in our Cisco 7606-S switch. Each of the ports have a X2-10GB-SR tranciever. When I look at the port with the "sh int tengig xx" command I see the following:
!
TenGigabitEthernet 4/1 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c.b0ca.75c0
!
TenGigabitEthernet 4/2 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c..b0ca.75c0(code)
Cisco Switching/Routing :: Cannot Access Server Or Ping On WS-X6708-10GE
May 2, 2012Connected server on a tenGigabitEthernet interface simple configuration setup
switchport
switchport access vlan 201
end
for server connection. Connected with Fibre. The interface is up and up but cannot ping server?
Cisco Switching/Routing :: QoS Doesn't Work In 3750?
Jan 9, 2013I created the configuration below to limit the bandwidth, but doesn't work
Qos - 3750
!
mls qosmls qos map policed-dscp 10 to 8!class-map match-all Testmatch access-group name ACL!policy-map QOSdescription Limit 10M set ip dscp af11 police
[Code]....
Cisco Switching/Routing :: Multicast On LAN Doesn't Work - 3750
Apr 16, 2013I have PC_A and PC_B connected to the same switch, and are put in the same vlan. PC_A is the master (source) and PC_B is the destination (client). IGMP Snooping is enabled by default.
Is there any reason why this should fail? There is no RP or any interface with PIM enabled. Its a flat network with a source and client in the same vlan...
IH-3750-LOADTEST-101#show ip igmp snooping vlan 724
Global IGMP Snooping configuration:
-------------------------------------------
IGMP snooping : Enabled
[Code].....
Cisco Switching/Routing :: 3750x - Aaa Authorization Doesn't Work In 15.0.1-SE
Aug 13, 2011c3750e-universalk9-tar.150-1.SE on 3750x
username cisco privilege 15 secret cico
aaa new-model
aaa authentication login default local
[Code]....
Console and telnet don't seem to auto authorize to level 15, I end up at level 1, I'm forced to use enable command.
Rolling back to c3750e-universalk9-mz.122-58.SE2 fixes it. Going back to c3750e-universalk9-tar.150-1.SE breaks it again.
is there some new behavior in cat 15 code (couldn't find it in config guide)? maybe a bug (couldn't find one)?
Cisco Switching/Routing :: 2960S QoS Configuration Doesn't Work
Apr 22, 2013my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.
Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET
This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.
access-list 100 permit ip any any dscp default
class-map match-all QoS_Floor_Limit
match access-group 100
!
!
policy-map QoS_Floor_Limit
[Code]......
Cisco Switching/Routing :: 2811 Console Server / Wiring Doesn't Work
May 22, 2012I'm trying to connect a Cisco 2811 using an octal cable to a Juniper MX480 console port.Since the distance between Cisco 2811 and router is 20ft, im using couplers and a straight-through cable for the lack of slack. This wiring doesnt work, however in another city it works going straight from the Cisco 2811 octal cable to the router since they are in the same rack.
View 4 Replies View RelatedCisco Switching/Routing :: Catalyst 4506 - Default Gateway Doesn't Work
Oct 26, 2011We have a Cisco Catalyst 4506 running: "Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version 12.2(25)EWA14, RELEASE SOFTWARE (fc1)" I have configured the default gateway as: ip default-gateway X.Y.116.65, However, when I do, "show ip route", it only shows the 3 connected networks and states "Gateway of last resort is not set". The Command "ip classless" is not set. I read on some blogs that this might explain the issue. However, when I go into config mode (config t), I get the following output.
View 9 Replies View RelatedCisco Switching/Routing :: Nexus 7009 - Syslog Configuration Doesn't Seem To Work For NX-OS
Sep 10, 2012we've been using IOS for a long time, but are relatively new to NX-OS. We've got a central syslog server that all our devices log to. No matter what we do, we can't get our Nexus switches to log there. Here's my current attempt:
Nexus 7009, NX-OS 6.0(1)
# sh logging server
Logging server: enabled
{redacted}
server severity: debugging
server facility: local7
server VRF: default
[code].....
The default VRF is working. I see log entries in the logfile, but nothing arrives at the syslog server. It's not a config issue on the server, because tcpdump shows that no packets arrive from the IP for loopback 0.
Cisco Switching/Routing :: Nexus 5548 Snmp-write Of Vlan Doesn't Work
Feb 22, 2012I am trying to configerate static switchports on our nexus 5548 (nx-os 5.1(3)N1(1)) over snmp.The support-list url... states that the CISCO- VLAN- MEMBERSHIP- MIB is supported.I can read the information, but if i try to set vmVlan or vmVlanType i get the message: "SET failed. ("ip-address"). Information: Not Writable."I can use set_request in general (e.g. CISCO-CONFIG-COPY-MIB). how to set the vlan and vlan-type over snmp?
View 3 Replies View RelatedCisco Switching/Routing :: 3560-X / USB Console Doesn't Work / RJ45 Works Just Fine
Nov 5, 2012I've got a 3560-X that passes POST according to console, but there are issues nonetheless...USB console doesn't work. RJ45 works just fine. No status lights turn on at any point (e.g. syst, xps...). 10g network module is installed with a 10g LRM SFP. All lights on the module are amber. However, it passes according to POST. Switch passes traffic, obeys config, etc. Link lights on RJ45 ports work fine. This was brand new out of the box. Thinking about trying IOS reload..
View 6 Replies View RelatedCisco Switching/Routing :: 6500 - TACACS Doesn't Work Via Telnet / Works Via Console
Apr 18, 2013I have a pair of OLD Cat6500's running CatOS:
WS-C6509 Software, Version NmpSW: 7.6(16)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 22 2005, 16:37:19
System Bootstrap Version: 7.1(1)
System Boot Image File is 'bootflash:cat6000-sup2k8.7-6-16.bin'
System Configuration register is 0x2
I know these are no longer supported, but I have to ready them for migration. Recently a problem began with these switches. What happens is that when I telnet to them, I cannot authenitcate via TACACS. This works fine for all our other IOS equipment, just not for these 2 switches. The error is:" % Error in authentication" and then I get kicked back to the login prompt.
The odd thing is that when I connect to the switch via the console port, I can authenticate fine with TACACS.
CMS> /c 14
[Code].....
Cisco WAN :: Upgrade From 871 To 891 Static Routing Doesn't Work
Jan 29, 2013I have a 871W router that works fine.I have 5 static ip addres's and use 2 in a nat pool. One i have mapped staticlly here is the configuration and it works fine:
! No configuration change since last restart
version 15.1
no service pad
service tcp-keepalives-in
[Code].....
Protocols / Routing :: Networking Doesn't Work From Workstation
Aug 27, 2011A month ago my ISP was routing half my subnet (129-254) over DSL. I just moved and routing no longer works without NAT. The issue is probably with the new DSL 'modem,' a zhone 1611-A1, but I am not sure how it should be configured.The 1611 is connected to a WRT610N, which works in NAT mode with the following settings:[code] With the previous settings, networking doesn't work from a workstation, though I can traceroute from the 610. I would like all workstations on the "LAN" to have fully addressable internet addresses like the previous configuration.There is an admin interface on the 1611, but the cursory settings I've tried don't work and I'm not a routing expert. The ISP is kindly routing my network, but they don't provide much support.
View 11 Replies View RelatedCisco Switching/Routing :: Why Does Routing Work Without Declaring Vlan10 On 2960s-24td-l
Oct 28, 2012I have recently split the voice vlan (10) from the data network (1), and am wondering why my catalysts and router do not require an interface Vlan10 statement. In the past I used OpenBSD boxes to do the routing, and I first needed to configure vlan 10 on the interface before I could get inter-vlan communication to work. With these Cisco devices it works, and I am wondering if it is because of VTP, for the fact that the ports maybe just pass all traffic, or is there some other explanation? Below is the setup, and firmware is up-to-date on all of the devices.
When I plug a phone into the POE SGE, the phone turns on, obtains an address on the proper subnet, and conversations are clear (whereas without the ip nat inside on the new subnet the calls had a lot of static). Possibly the reason that it works is because the phones properly create the tcp/ip packet, and it hops over the trunks and creates the states so that traffic routes back properly. I will install wireshark to see exactly what is going on, but is there a simple explanation that I am overlooking?
Cisco Switching/Routing :: 871 Doesn't Let To Make Changes?
Jul 2, 2012Our 871 no longer allows us to make changes to it. I was told the contract ran out, so I renewed it and Cisco support then added the contract to my serial number. What now? Is there a step required to have the router check in with Cisco so that it becomes "unlocked" for me to make changes?
View 1 Replies View RelatedCisco WAN :: No Compatibility Mentioned With WS-X6708-10GE Module
Dec 3, 2011I was looking at the data sheet for the VS-S2T-10G and there was no compatibility mentioned with the WS-X6708-10GE module.Is this module compatible with this new supervisor?
View 2 Replies View RelatedCisco Switching/Routing :: 3945 PBR Doesn't Appear To Be Working
May 1, 2013I have a 3945 router with two interfaces connected to my firewall, one to the management interface and another to my dmz. I'm running eigrp between all my network devices. The problem I'm running into is when I try to ssh to the management interface of the 3945 the traffice hits the firewall, then goes right to the management interface as it should, but the return traffic is trying to use the dmz interface since that is how the router knows to get back to my computers network. I created 2 route-maps to try and address this issue. [code] I've applied the MANAGE_IN route-map to all interfaces that might have inbound traffic destined for the management network and applied the MANAGE_OUT route-map to the management interface. The MANAGE_IN policy appears to be functioning correctly, the MANAGE_OUT doesn't appear to be functioning correctly. When I look at traffic from my host going to the management interface I see it still trying to return through the dmz interface.
View 11 Replies View RelatedCisco Switching/Routing :: 2950 - Etherchannel Doesn't Go Up
Jun 11, 2012I have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies View RelatedCisco Switching/Routing :: WS-C6509-E Doesn't Remove IPs From ARP
Mar 25, 2012we have a WS-C6509-E WITH SUP VS-S720-10G, and IOS s72033-advipservicesk9_wan-mz.122-33.SXI5.bin. [code]
From, what we can see, whenever we try to clear arp-cache, it doesn't remove the IPs from the ARP. We've checked a bug in the IOS 12.2(33)SXH4 with the same issue, in version SXI4 is solved, but I have version SXI5, it is supposed to be fixed, from this caveat CSCtf16300, since it says it was fixed on 12.2(33)SXI4, it should be fixed on SXI5, right ?
VPN Doesn't Work Properly?
Jan 11, 2011I have an problem with VPN connection on notebooks. Sometimes the VPN connection works perfectly, and other times it just doesn't work at all.The Cisco VPN client software is version 5.0.04.0300. Operating system is Windows XP Prof SP2.When the connection fails, the client statistics window shows "Bytes Received: 0".Rebooting the system, has no effect
View 1 Replies View RelatedNew Share Doesn't Work
Jan 27, 2011Normally, when one right clicks on a drive letter having opened 'My computer', then select 'Sharing' there is a warning about sharing a whole disk and the option to accept anyway.One laptop doesn't offer that. It just shows the admin share of C$ immediately. If I choose 'New' at the bottom of the panel a new drive letter and drive name can be entered but it can never be accessed over the network! It shows up in the workgroup but I get a network error 'Network path not found' if I try to access it. I can ping the laptop from anywhere by name and IP address.The laptop can access all the other PCs without any problem.
View 12 Replies View RelatedCisco Switching/Routing :: 3500XL Computer Doesn't Get IP Address
Jul 10, 2012I'm configuring a catalyst 3500XL, but I'm having a problem, when I connect an ip phone it works just fine but if I connect a computer to the pc port in the phone the computer doesn't get an ip address. The switch is configure with two vlans Voice and Data and is connected from fa0/24 to a Catalyst 3560 fa0/46. I did configure both ports as trunk.
View 9 Replies View RelatedCisco Switching/Routing :: Nexus 3048 VPC Doesn't Form
Jun 11, 2012I am building up vPC on 2 x Nexus 3048 and found that it did not work properly.The current config as follows,
1. OS: n3000-uk9.5.0.3.U2.2.bin
2. Peer link: 10 x 1G (E1/1 - E1/10) on both devices (I am wondering that 1G interface supports vPC Peer-Link. I heard that upgrading to U3.2 image will work for 1G rather than 10G... )
3. They can ping each other via management IPs
4. Edge switches vPC have not been built yet (I am focusing on Peer-Link and vPC role selection)
[code]....
Cisco Switching / Routing :: 3560 Doesn't Map DSCP Values
Apr 29, 2012I've been working on a 3560 that doesn't seem to map dscp values to a new value: mls qos map dscp-mutation ToR1 22 24 to 46
[Code]....
On the router on the other side, I created an acl that matched on dscp 46, but it doesn't match on it. I've tried moving the mutation map to the ingress interface and I've tried setting dscp with a service policy instead of marking COS and using internal dscp. Where is the mutation map supposed to be placed: ingress or egress? Also, I added an entry in the acl on the router to see if I was mapping to dscp 24, and I am:
[Code]....
So it seems like the mutation map is being ignored completely. Any reason why?
Cisco Switching/Routing :: 6509 / Route-map Doesn't Get Any Hits
Dec 11, 2011My network has two connections to a third party via links on two seperate ASA , one in location A and one in location B. The link in location A is the primary connection and the other in location B should be used by only two terminals (term1, term2) in location B. ASA are running OSPF and are redistributing static routes as metric-type 1 in OSPF. In order to achive the aforementioned goal, I have configured a route-map on ASA location B, that sets the metric for the route towards the third party to a high value (100). This way, all routers, even those in site B prefer the exit through location A (metric about 24).
I have checked that my routers correctly have the route to the 3rd party through location A, and the OSPF database has records for the network from both locations.In location B, I have configured the following route-map (on 6509)
route-map PREFER-LOCAL-ROUTER permit 10
match ip address XXX
set ip next hop locationB-ASA
int vlanYYYY
ip policy route-map PREFER-LOCAL-ROUTER
[code]....
From the terminals (term1 and term2) I have tried a traceroute towards the 3rd party's subnet, but I don't get any match neither on the access-list nor on the route-map. Unfortunately I have no other way to test that my configuration is correct, since the application on the terminals, that should access the 3rd party network, is not currently running.
I also addedd the statements below to the access-list, because of the test with tracert:
permit icmp host term1 route_to_3rd_party 0.0.255.255
permit icmp host term2 route_to_3rd_party 0.0.255.255
Nothing changed...Is there something wrong with the above config? Is there a chance that there is a problem with the IOS, that simply doesn't show any hits?
Cisco :: LMS 4.2 Syslog Collector Doesn't Work
May 21, 2013my LMS 4.2, syslog collector on LMS doesnt working even service syslog collector running normaly and also i saw in syslog_info is working to collect syslog from all router but not show up in dashboard monitoring.I have setting on every router to logging (ip address LMS) but on LMS no any syslog from router can collect.i did a selftest from LMS there are all PASS except nslookup fail, it is has relation with syslog not show up on dashboard?
View 5 Replies View Related