Cisco Switching/Routing :: Catalyst 4506 - Default Gateway Doesn't Work
Oct 26, 2011
We have a Cisco Catalyst 4506 running: "Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version 12.2(25)EWA14, RELEASE SOFTWARE (fc1)" I have configured the default gateway as: ip default-gateway X.Y.116.65, However, when I do, "show ip route", it only shows the 3 connected networks and states "Gateway of last resort is not set". The Command "ip classless" is not set. I read on some blogs that this might explain the issue. However, when I go into config mode (config t), I get the following output.
View 9 Replies
ADVERTISEMENT
Apr 1, 2013
Using Network Assistant in XP, plugged ethernet cable to first front port and keep getting "Failed to get Default Gateway. Check your security settings to make sure the current Java Virtual Machine is not prevented from running commands.", I have tried reducing secruity to nothing but I still get the same problem.
I also have an official cisco console cable and tried that, but Hyperterminal just does not pick it up when plugged in. I have left the IP dynamic, turned off all netowork adapters apart from ethernet, set the baud rate etc... correctly, still no joy.
View 5 Replies
View Related
Sep 10, 2012
i am facing a problem when the client vlan is commmunicating with the default gateway on the core 3750-x.
ios in 3750-x core is 3750e-universalk9-mz.150-2.SE.bin. But, client to client communication is happening without any dealy and icmp is less than 1 ms always.
When try to ping default gateway of client vlan, it is getting delayed (variable icmp delays). Is this an ios bug?
View 2 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Mar 19, 2013
Does SUP 7E is comatible with IOS? It came with IOS-XE preloaded and there are no IOS software listed under downloads.
View 3 Replies
View Related
Mar 25, 2013
My inherited network has a Cisco Catalyst 4506 with a WS-X4124FX–MT fiber card that connects to twelve Cisco 2950 switches over 62.5 micron multimode fiber at 100 Mbps. I do not know my run lengths (or even where the conduits run), but the furthest switches are well over a thousand feet from the server room. Any appropriate test equipment to provide this information soon.
We are looking at upgrading the main switch to a Catalyst WS-C4507+E with two WS-X4712-SFP+E cards and the closets to Cisco 2960S-48TD-L switches. Assuming this is a reasonable move, my question is about choosing the appropriate SFP’s for our current and future needs.
I am aware that 62.5 micron multimode fiber is the least favorable for extended lengths, but I will not be in a position to replace it for at least a year. If I purchase 10 Gbps modules, like the SFP-10G-SR or SFP-10G-LRM, can they “throttle down”, either automatically or by setting a parameter, to communicate at slower speeds over distances that exceed their 10 Gbps maximum link lengths on multimode fiber?
View 1 Replies
View Related
Dec 19, 2011
I am implementing a guest wireless network to work alongside my internal network. The guest network will use the existing switching network and will be separated by VLANs. I have the ASA set so that traffic can get to it and out to the Internet. I can set up a workstation on the same VLAN as my guest network and can route inside my network (strictly doing this for testing purposes). Where I am having problems is with the Catalyst 4506 switches and the ip routing. I had two separate "ip route" statements defined on my switches.
ip route 10.200.2.0 255.255.255.0 10.200.2.254
ip route 0.0.0.0 0.0.0.0 10.100.100.254
I have discovered that the traffic is always following the default route despite the fact that my IP address on my test workstation falls in the 10.200.2.x network. I was looking at documentation and found that it is possible to set up policy-based routing on the core switches. Can you have two "ip route" statements defined like this to segreate traffic or do I have to use PBR for routing (or a combination) in this case? If I define PBR then how does that impact my existing routing? I need to make sure that I can still route the existing traffic while I'm configuring this change.
View 9 Replies
View Related
Jan 20, 2013
Our customer get the problem that the switch count the 5mins input/output rate of connected traffic interface always ZERO.The problem only occur in the module 3,4 and 5 interface, module 2 has no problems.
-------------------------------------------------------------------------------------------------
Catayst 4506E
12.2(52)SG
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E 2 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 3 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E 4 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E 5 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E
[code]....+
View 2 Replies
View Related
Aug 4, 2012
I'm trying to NAT to a device that doesn't have a default gateway; effectivley we want to talk to the device as if we're on the same LAN but using only port 80.Here's the setup:
Remote Device on LAN A <-> RA <-> Remote router WAN A <-> ISP <->--
--<->ISP <-> Remote router WAN B <-> RB <-> Remote Device LAN B (no default gateway)
We're using Cisco IOS on 877s and I'm sure this can be done
View 5 Replies
View Related
Oct 18, 2012
imagine I want to make VLAN200 workstations communicate like the show in the attachment. What would be the default gateway to be configured in the workstation? If I configure 192.168.1.1 as the default gateway (R1 interface fa0/0) is this right?That could be possible because the switch should be configured with command "ip default-gateway 192.168.1.1"?
View 4 Replies
View Related
Mar 6, 2012
I have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies
View Related
May 3, 2012
This would probably sound like a stupid question but it took at least 2 hours of my time so far. I have a 3750 switch where a router and a server is connected. From the switch I can ping the router and server with no issue (directely connected). But from the server I am not able to ping the router. The router and the server are in the same subnet. The router is configured as the default router for the server. I am not able to ping the server from the router either. Here's the output of the ip route from the router. The server IP address is 10.1.200.21 and the router IP address is 10.10.200.1
10.0.0.0/8 is variably subnetted, 8 subnets, 3 masks
C 10.1.30.0/24 is directly connected, FastEthernet0/0.30
C 10.1.20.0/24 is directly connected, FastEthernet0/0.20
[Code].....
View 14 Replies
View Related
Jan 24, 2013
I have a Cisco 2960 ( WS-C2960-8TC-S) running 12.2(46)SE C2960-LANLITEK9-M image.I would like to set an ip route 0.0.0.0 0.0.0.0 87.101.156.97 but the current image does not allow.Will ip default-gateway 87.101.156.97 work or do I need ip routing ?The ISP has provided a /30 address and we are using an additional /29 for our network devices. I dont think this image can be upgraded. I need to forward routes directly out to ISP. [code]
View 5 Replies
View Related
Apr 10, 2013
I have a bit of a mystery on my hands. I had a whole campus of Cisco 3750's cache a new default gateway. Example
Cisco3750#sh ip redirects Default gateway is 10.10.10.1
Host Gateway Last Use Total Uses Interface172.16.0.5 10.10.101.179 0:00 185749 Vlan1172.16.0.76 10.10.101.179 0:01 47254 Vlan1192.168.0.154 10.10.101.179 0:00 183090 Vlan1
My question is what generates a IP Redirect packet or how does the switch know what to change the gateway to? As in my case the changed gateway was a dead IP address. So I am at lose how this happened. I this case the Host IP's are network management servers conducting polling.
View 3 Replies
View Related
Aug 9, 2012
I have a 3500 XL switch with the following default gate IP address that i need to clear from the switch but not quite shore how to remove it.
I've removed the customer original Ip for security reason as this is an open discussion forum and just replaced with 1.1.1.1
switch#show ru
Building configuration...
Current configuration:
!
[Code].....
View 2 Replies
View Related
Oct 15, 2012
I have created two vlans, vlan 1 data and vlan 200 voice. the issue is that when an on one vlan i cannot ping the default gateway of the othe vlan from my PC. An using sge 2010p switches.
below is my configuration
p route 0.0.0.0 0.0.0.0 192.168.0.1
ip dhcp relay address 192.168.0.100
ip dhcp relay enable
ip dhcp information option
interface vlan 1
ip dhcp relay enable(code )
View 3 Replies
View Related
Feb 12, 2012
I'm trying to configure an IPSEC VPN + tunnel for multicast data. When the default gateway is set on the router (1841) it works fine but if I only set a route to the IPSEC peer via our gateway then the tunnel fails to come up. The end point is to a 3rd party. [code]
I found that if I add a static route for the tunnel destination via fa0/0, the public facing interface, the tunnel comes up..ip route 10.23.4.2 255. 255. 255. 255 FastEthernet0/0
and I can then ping the tunnel IP at the far end - 10.23.0.5.Why would that be? Is there a better way to do this without using a default route??
View 4 Replies
View Related
Jul 25, 2012
I have a design hurdle that I cannot seem to cross. I have two sites and I need the same VLAN to span both sites. I have accomplished this using L2TP but my issue is that I can no longer assign a gateway for this VLAN on the router. The 2 routers are 2821's and are connected with a dedicated fiber run.
Ant recommendation for how this could be accomplished? It would be great if I could have the same gateway at both sites by leveraging some sort of bridged interface (BVI so I've heard) but I am at a loss as to where I should start with this. Also, this is not the only VLAN that needs to traverse the link.
View 2 Replies
View Related
Sep 19, 2012
Recently we observed that newly installed WS-C3560CG-8PC access switches are able to communicate without a default route or default gateway.The 3650 switches are used as a layer2 access switch behind a layer3 distribution/core. They have only the management VLAN configured for IP with a single address.
The ARP table looks like there is an implicit proxy-ARP request sent for any IP address.
We definitely have no configuration whatsoever which would explain this.
Is this a new feature? We don't observe that with the older 2960-series...
Here is a brief trace of what's happening (debug arp):
host41#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Sep 20 14:44:06.706: IP ARP: sent req src 10.1.8.41 1833.9dc9.wxyz,
dst 1.1.1.1 0000.0000.0000 Vlan1
Sep 20 14:44:06.711: IP ARP: rcvd rep src 1.1.1.1 2c54.2dd3.wxyz, dst 10.1.8.41 Vlan1..
[code]....
The mac address if of course the mac address of the layer 3 interfaces of the distribution switch, no surprise here (proxy ARP is turned on by default).
Why is the 3560 sending out proxy arp requests without being told to? As far as I understood proxy ARP on Cisco IOS it only means it will reply to a proxy ARP request but will not send out proxy ARP requests by default.
View 3 Replies
View Related
Apr 11, 2012
I have a 3560G and an ASA FW, for which I am trying to use PBR to append the next hop. The gateway is the switch VLAN address and the amended net hop is the same VLAN interface on the ASA. Trouble is, I can ping the FW from a client, but not the switch. If I remove the route map, I can ping both. Even more strange is this is the case for some VLANs, but not all!
Config:
HOST ON VLAN 96
IP 10.11.120.99
S/M 255.255.255.240
[Code].....
View 2 Replies
View Related
Aug 25, 2012
I had setup a lan infrastructure with 5 3750 stack swithes. In these 3 of them are in one stack which is acting as access switch, 2 of them in another stack which is as core switch where all the SVI is configured. Now, when i tried to ping from our edge pc which is connected in access switch to default gaeway, which is configured in core switch, the ICMP is getting delayed . But when try to ping from the same edge pc to another user PC, it is getting less tahn 1 millisecond icmp replies.
why icmp is delaying to default gateway , but working with another edge to edge pcs without any delays?
View 1 Replies
View Related
May 21, 2012
We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too.
At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites.
Testing
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps?
View 15 Replies
View Related
Mar 5, 2013
We have a 6509 series of core switches and 3750 series of L2 switches, There is no default gateway or any static routes to any IP.VLAN 1 is made admin down and another vlan is used for all communication here in this environment
Attached is configuration for reference But still I am able to take telnet or SSH. I want to know how telnet or SSH or tacacs authentication happens without any static or default route.
View 4 Replies
View Related
Jul 4, 2012
A check out a network segment and want to know why SwA has a static route to SwB if SwA already has a Default GW to Core?
(SwA, SwB - Catalyst3560, Core - Catalyst4948)Note, there are distribute list on SwA - it does not has any OSPF route (exclude O*IA).
Does this mean when SwA send out packet with DA 10.5.64.0/26, Core will use only L2 switching (instead of L3)? Is this more effectively for Core Switch?
Pleace check my reasoning:
1. When use a static route: SwA receive packet from Vlan 20 with DA 10.5.64.0/26 it will strip out Dest. MAC and replace it with MAC of SwB. Core will switch this packet to SwB based on mac add. table (l2 switching)
2. When SwA has only Default gateway and receive packet from Vlan20 with DA 10.5.64.0/26 it replace Dest. MAC with Core MAC. Core receive this packet, lookup route table for 10.5.64.0 entry and forward packet base on this.
View 6 Replies
View Related
Aug 14, 2012
4500 switch is connected to 2960 switch.
4500 config
Vlan 10
name Data
It has ip helper configured that points to DHCP.From 4500 switch port - port x connects to 2960 port.Port x is configured as trunk between 4500 and 2960.
2960 config
vlan 10
name data
All user ports are configured under vlan 10 and as access ports.Port x is trunk port connected frpm 2960 to 4500 switch allowing vlan 1 and 10 only.This switch has no default gateway configured.
We connected user PC on 2960 switchports and they were able to get the IP from DHCP server and were able to access the network? My question is how users on 2960 switch are able to access the network without ip default-gateway configured on 2960 switch?
View 6 Replies
View Related
Aug 6, 2011
I upgraded the firmware for my WRVS4400N v2 to version 2.0.2.1 firmware, now old and default passwords don't work. I have tried resetting it as well, and the default password does not work.
View 1 Replies
View Related
May 16, 2012
We had a core switch (4503), distribution switches and access in our network and consists of many vlans. Almost all vlans uses DHCP Pools. But for few vlans DHCP is not yet configured. Recently one of the rogue user in vlan 1 gave the corresponding interface vlan ip of core switch (gateway) as his ip and caused a prolonged network outage for the vlan. Any way we are going to seggregate vlan 1 into different vlans, but before that we need a temporary plan to block such kinds of attack.What are the possible ways we can avoid the network outage problem even if a user gave the gateway ip to the machine?
View 3 Replies
View Related
May 22, 2013
|_voip PBX___|-----|__3650___|------fiber-------------|__3650_____|------|_voipphone__| I have a case where voipphone is registered on the voippbx but peaple on both end can't hear each other . No ACL on both 3650 , no firewalls between them , distance is about 2 miles . I tried to make telnet x.x.x.x 1720 or 1719 or 1721 (h323 ports) to opposite switch -connection refused . How can test if ports are open on the 3650 ? Is it coorect If I create allowing acl and apply it on both 3650 on the interfaces connected one switch to voippbx "IN" , second switch on the interf connected to voipphone "IN" ?
View 3 Replies
View Related
Nov 1, 2011
the problem shows an error in a switch catalyst 2900XL - its a 2924 -, i was copying the image of the ios via xmodem and before finished the the power energy in the facility shuts down, when the energy supply returns the switch get power energy normally but the flash memory doesn't initialized and the loader stuck when i try to initializy the flash or reset
this is the error that shows me:
switch: flash_init
Initializing Flash...
flashfs[0]: 21 files, 2 directories
[Code]....
View 8 Replies
View Related
Aug 8, 2012
Just I have upgraded some 2960S to IOS 15.0(2)SE from a IOS 15.0(1)SE3 and the catalyst don't switch any IPv6 traffic. Don't work any RA and also don't work any unicast IPv6 traffic from any interface. I can see some references to IPv6 changes in the FHS (First Hop Security) in the Release Notes, but no any reference to changes in the configuration.
The switches don't have any IPv6 specific configuration and the sdm is the default templata. Returning to 15.0(1)SE3 everything work ok.
On Catalyst 2960, and 3560E this IOS version seem to work fine with IPv6.
View 1 Replies
View Related
Dec 12, 2012
Does the port adaptor PA-MC-2E1/120 work with the Catalyst Switch 6506E (Sup Engine: 720-3B)? We have bought a Enhanced FlexWAN card for this port adaptor.I read through the cisco website and seem to get confusing answers whether they are compatible.
View 1 Replies
View Related
Apr 4, 2013
I have the following zebra.conf on my router box "A":
hostname nuclear-router
password password
enable password password
interface eth0
ip address 192.168.2.1/24
multicast
[code]...
eth0 is connected to a switch and contains the 192.168.2.0/24 range, and A is connected to my WRT54GL "B" (with IP 192.168.1.1, containing 192.168.1.0/24 range, DHCP serves IPs above .100) wirelessly. B is connected directly to my DSL modem.
The problem is that when I specify the default route using the interface name, I can't connect to the internet from A or any hosts behind it - I'm always hit with a "no route to host" error. Name lookup and pinging any local host (even in a different range) or the DSL modem works fine - it's only when going beyond the modem that things stop working. However, when I use the IP of B as the gateway, it works fine. I noticed that route output on A when the default route was specified using the interface alone had only an asterisk in the gateway column. I was under the impression that these approaches should be identical in practice, so though I got it working, I'd like to know what I'm misunderstanding (and/or misconfiguring). Why didn't the default route work when specified using just the interface?
All routers and the modem too have RIP (version 2) enabled, and of course the password isn't really the word "password".
View 2 Replies
View Related
Jul 5, 2010
We have an AIR-LAP1142N-E-K9 deployed in a H-REAP setup.This AP already got the configuration from the WLC when it was deployed at a remote site.Now we moved it to another site, but it doesn't appear in the WCS and i don't see any CAPWAP debug messages on the WLC.The routing work fine between the AP and the WLC, the AP also gets an IP address from DHCP and also received Option 43 information.
Now my guess was that the AP doesn't associate with the WLC because it has the old config file and it runs in local mode(without trying to connect to the WLC).We want to reset to factory defaults because we want to delete the configuration and force the AP to get a new config from the WCS.I don't know the enable password so i had to use other methods for reseting to factory defaults.
I tried to use the information from here:[URL]I used the "MODE button":I get the following message from the console:
"button pressed for 5 seconds
process_config_recovery: set IP address and config to default 10.0.0.1"
View 24 Replies
View Related
