Cisco Switching/Routing :: Multicast On LAN Doesn't Work - 3750
Apr 16, 2013
I have PC_A and PC_B connected to the same switch, and are put in the same vlan. PC_A is the master (source) and PC_B is the destination (client). IGMP Snooping is enabled by default.
Is there any reason why this should fail? There is no RP or any interface with PIM enabled. Its a flat network with a source and client in the same vlan...
IH-3750-LOADTEST-101#show ip igmp snooping vlan 724
Global IGMP Snooping configuration:
-------------------------------------------
IGMP snooping : Enabled
[Code].....
View 19 Replies
ADVERTISEMENT
Jan 9, 2013
I created the configuration below to limit the bandwidth, but doesn't work
Qos - 3750
!
mls qosmls qos map policed-dscp 10 to 8!class-map match-all Testmatch access-group name ACL!policy-map QOSdescription Limit 10M set ip dscp af11 police
[Code]....
View 6 Replies
View Related
Dec 10, 2012
I have a subnet with a GPS clock on it that connects into a Cisco 3750. The 3750 has another subnet hanging off of it that connects into a firewall then to a server. I need the server to get time from the GPS clock. Any way to pass the NTP through the 3750? The 3750 has the 3750-IPBase code running on it so the multicast support is limited. I am under regulatory restrictions that only allow traffic to flow from the higher security level (were the time server is) to lower security level (were the server is). This prevents me from having the server go to the clock for updates.
View 1 Replies
View Related
Feb 19, 2013
I try to pass multicast traffic between two vrf on the same 3750 switch. I have IP services IOS and sdm template routing.
here is my config:
ip routing
!
ip vrf vpn2
rd 1:1
mdt default 232.1.1.1
route-target export 1:1
route-target import 1:1
[code]....
Now I'm stuck - I don't know what to do to pass multicast traffic. Do I have any chance to run this config on 3750 chassis?Perhaps "Configuring Multicast VPN Extranet Support" document will be useful, but it concerns Catalyst 6500? [URL]
View 0 Replies
View Related
May 12, 2013
I've been handed a requirement to try and get a multicast server working on my setup. Trouble is, I don't know if I can with the feature set I have on my switches. What is desired is that a multicast server (stand alone, but network connected, obviously) be accessible by everyone on the local network (multiple V LAN's, multiple SVI's) in the building.
All users will be connected to the one switch stack, although some will want to be wireless (which is one of the separate V LAN's) - I don't care if the wireless requirement goes by the wayside - they can sod off. :-) The main purpose will be multicast, high quality video.
I have a single switch stack consisting of two (soon to be 3) WS-C3750X-48P switches running the IP BASE feature set.
Question - can I do this on IP BASE, or do I need to upgrade to IP SERVICES?
If I can do it on IP BASE, does anyone have any links/pointers to setup this properly? Currently installed IOS is 12.2(58)SE2.
View 3 Replies
View Related
Jun 7, 2012
I have a 2960G that I keep on the bench as a work switch. I assigned an IP address to it. The techs have had trouble imaging workstations using GHOST. Do any config changes need to be made to enable multicast to work? Everything is in VLAN1 at this point and the GHOST server is also the DHCP server.
View 1 Replies
View Related
Mar 3, 2013
I have one server which run some application for wireless user. this server forward multicast packet to wireless user. server and wlc physically connect to cisco 3750 switch.i want the server forward the multicast packet to wireless users.server access vlan 4.wlc controller have 2 vlan: 90 and 110.and wireless user some of vlan 90 and some of vlan 110.i enable igmp snooping on wireless controller. and enable globally command but it is not working.which additional configuration i need on cisco switch.
Switch(config)# ip igmp snooping
View 16 Replies
View Related
Jun 19, 2012
A multisite network is currently supporting muticast using PIM dense mode, which is enabled on router/switch LAN and WAN interfaces across all locations. I am about to introduce Nexus switches to the main LAN. How can I make dense and sparse mode coexist to ensure flow of muticast traffic between devices supporting and dense and sparse mode? Eventually, I want to transition to the sparse mode; however, it has to be done gradually, even within a single site. The leacy equipment includes Cat 3750 and 4500s.
View 2 Replies
View Related
Aug 13, 2011
c3750e-universalk9-tar.150-1.SE on 3750x
username cisco privilege 15 secret cico
aaa new-model
aaa authentication login default local
[Code]....
Console and telnet don't seem to auto authorize to level 15, I end up at level 1, I'm forced to use enable command.
Rolling back to c3750e-universalk9-mz.122-58.SE2 fixes it. Going back to c3750e-universalk9-tar.150-1.SE breaks it again.
is there some new behavior in cat 15 code (couldn't find it in config guide)? maybe a bug (couldn't find one)?
View 9 Replies
View Related
Apr 22, 2013
my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.
Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET
This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.
access-list 100 permit ip any any dscp default
class-map match-all QoS_Floor_Limit
match access-group 100
!
!
policy-map QoS_Floor_Limit
[Code]......
View 6 Replies
View Related
Apr 26, 2013
I am working with 3750 switch.I console the switch and turn it on and it doesn’t show text in hyper terminal with any BAUD (I tried all the speeds). The hyper terminal works with other switches so the problem is not with the hyper terminal.when I tried to break the password it stuck after I was writing "flash_init" and when I entered or typed text it show only garbage characters. I tried to break the password with all the speeds and it shows garbage output. I tried to turn on the switch and hold control + break and it showed the text only with the speed 115200, but after I left holding and tried to type it showed only garbage again. Also I tried to copy text from the notepad to the hyper terminal.
View 6 Replies
View Related
May 21, 2012
we have three separated network segments going to one Cisco 3750 switch all is L2 .. from this switch is 100 mbit uplink.we need to apply some Qos mechanism not to saturate line by traffic from one network.. Configuration from various reason CANNOT be done on switch where 100Mbit line is terminated.. so all must be done on SW1,2,3..Correct me if iam wrond but as switches doesnt see traffic from other network iam affraid only think we can do is limit bandwidth on links going into SW1,2,3 to 33 Mbit.I found commad srr-queue bandwidth limit.But links going to SWs are 1Gbit so if i force bandwidth to 10% (minimum what command allows) its 100 Mbit..If I force speed on those links to 100Mbit and than apply srr-queue bandwidth limit to 30% doest it work.??. Will srr-queue bandwidth limit speed to 30Mbit?? Or srr-queue bandwidth limit is calculated from maxim speed of interface?
View 1 Replies
View Related
Oct 27, 2012
we can't start WS-X6708-10G-3CXL on WS-C6506-E. [code] we did try on conf t mode "power enable module 3" and it didn't work. [code]
View 2 Replies
View Related
Dec 11, 2012
a new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?
portfast an dother parameters are intact.
View 2 Replies
View Related
May 30, 2013
I have 2 local accounts on a 3750 that kick in should radius be unavailable. If I log in as the admin account it gets priv 15, if I log in as the other user it gets privilege 3 which is correct, by my commands dont work, this is what I have added and the strange thing is I've dont this many times before on our other switches
username admin privilege 15 secret ***
username users privilege 3 secret ***
aaa new-model
[Code]....
View 2 Replies
View Related
May 22, 2012
I'm trying to connect a Cisco 2811 using an octal cable to a Juniper MX480 console port.Since the distance between Cisco 2811 and router is 20ft, im using couplers and a straight-through cable for the lack of slack. This wiring doesnt work, however in another city it works going straight from the Cisco 2811 octal cable to the router since they are in the same rack.
View 4 Replies
View Related
Oct 26, 2011
We have a Cisco Catalyst 4506 running: "Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version 12.2(25)EWA14, RELEASE SOFTWARE (fc1)" I have configured the default gateway as: ip default-gateway X.Y.116.65, However, when I do, "show ip route", it only shows the 3 connected networks and states "Gateway of last resort is not set". The Command "ip classless" is not set. I read on some blogs that this might explain the issue. However, when I go into config mode (config t), I get the following output.
View 9 Replies
View Related
Sep 10, 2012
we've been using IOS for a long time, but are relatively new to NX-OS. We've got a central syslog server that all our devices log to. No matter what we do, we can't get our Nexus switches to log there. Here's my current attempt:
Nexus 7009, NX-OS 6.0(1)
# sh logging server
Logging server: enabled
{redacted}
server severity: debugging
server facility: local7
server VRF: default
[code].....
The default VRF is working. I see log entries in the logfile, but nothing arrives at the syslog server. It's not a config issue on the server, because tcpdump shows that no packets arrive from the IP for loopback 0.
View 3 Replies
View Related
Feb 22, 2012
I am trying to configerate static switchports on our nexus 5548 (nx-os 5.1(3)N1(1)) over snmp.The support-list url... states that the CISCO- VLAN- MEMBERSHIP- MIB is supported.I can read the information, but if i try to set vmVlan or vmVlanType i get the message: "SET failed. ("ip-address"). Information: Not Writable."I can use set_request in general (e.g. CISCO-CONFIG-COPY-MIB). how to set the vlan and vlan-type over snmp?
View 3 Replies
View Related
Nov 5, 2012
I've got a 3560-X that passes POST according to console, but there are issues nonetheless...USB console doesn't work. RJ45 works just fine. No status lights turn on at any point (e.g. syst, xps...). 10g network module is installed with a 10g LRM SFP. All lights on the module are amber. However, it passes according to POST. Switch passes traffic, obeys config, etc. Link lights on RJ45 ports work fine. This was brand new out of the box. Thinking about trying IOS reload..
View 6 Replies
View Related
Apr 18, 2013
I have a pair of OLD Cat6500's running CatOS:
WS-C6509 Software, Version NmpSW: 7.6(16)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 22 2005, 16:37:19
System Bootstrap Version: 7.1(1)
System Boot Image File is 'bootflash:cat6000-sup2k8.7-6-16.bin'
System Configuration register is 0x2
I know these are no longer supported, but I have to ready them for migration. Recently a problem began with these switches. What happens is that when I telnet to them, I cannot authenitcate via TACACS. This works fine for all our other IOS equipment, just not for these 2 switches. The error is:" % Error in authentication" and then I get kicked back to the login prompt.
The odd thing is that when I connect to the switch via the console port, I can authenticate fine with TACACS.
CMS> /c 14
[Code].....
View 2 Replies
View Related
Apr 5, 2012
I have a 3750-48P when plugged in has fans that spin up, but no lights on the front of the chassis. Does this mean the power supply is bad? If its bad, why do the fans power up? Also, i am not receiving any data through the console.
View 6 Replies
View Related
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
View Related
Jan 29, 2013
I have a 871W router that works fine.I have 5 static ip addres's and use 2 in a nat pool. One i have mapped staticlly here is the configuration and it works fine:
! No configuration change since last restart
version 15.1
no service pad
service tcp-keepalives-in
[Code].....
View 1 Replies
View Related
Aug 27, 2011
A month ago my ISP was routing half my subnet (129-254) over DSL. I just moved and routing no longer works without NAT. The issue is probably with the new DSL 'modem,' a zhone 1611-A1, but I am not sure how it should be configured.The 1611 is connected to a WRT610N, which works in NAT mode with the following settings:[code] With the previous settings, networking doesn't work from a workstation, though I can traceroute from the 610. I would like all workstations on the "LAN" to have fully addressable internet addresses like the previous configuration.There is an admin interface on the 1611, but the cursory settings I've tried don't work and I'm not a routing expert. The ISP is kindly routing my network, but they don't provide much support.
View 11 Replies
View Related
Mar 12, 2013
I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
First step: enable multicast routing
Second step: on both interfaces (Fe 0/1 and Fe 0/2) - ip pim sparse-mode
Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
When I start VLC on computer nothing happend. If I try to connect computer on same subnet where is source of multicast streams it works fine.What I am doing wrong ? Is there anything about routing ? All subnets are directly connected. RP is not needed if I have one router or ?
View 11 Replies
View Related
Mar 23, 2013
I need to enable multicast routing on 2960s but the command "ip multicast-routing" isn't available on my release (12.2.(55)).
From which release this command is available?
View 1 Replies
View Related
Nov 14, 2012
I have a problem on my catalyst 6509 on which I would like to do the following things :
I have some Vlans in which multicast is enabled.
In tose Vlan theres is a router which is default router for equipements.
I had enabled multicast routing because some Vlan needs to exchange multicast informations, but I wolud like to make difference between Multicast traffic. For example I have 5 vlans:
Vlan 1 and 2 need to exchange Multicast informations but the don't need multicast information from Vlan 3 and 4
Vlan 3 and 5 need to exchange Multicast informations but the don't need multicast information from Vlan 1 and 2
Vlan 5 is independant Vlan but doesn't need to have multicast information from all others vlan.
Last problem, equipement on differents vlan can use the same Mulkticast group address. In this case, Multicast routing is not working between Vlan 1 to Vlan 2 and Vlan 3 to Vlan 4.
View 6 Replies
View Related
Mar 8, 2013
I am configuring multicast in a environment where I have a 4506 at each site (4 total) and a 6506 as the core. Each 4506 is connected via layer 3 to the 6506. I have a mix of 3560s, 3548s, and 2960s connected to the 4506s and the 6506 via layer 2 trunk
I have multiple multicast sources and hosts communicating at a time (multiple cameras sending video / multiple computers receiving video). So this is not a scenario where there is 1 sender and many receivers. This would be many senders (~50) and some receivers (~10)
Sample Diagram:
->3560
|
6506 --> 4506 --> 3548
| |
| --> 2960
|
4506 --> 2960
|
-->3548
I configured ip multicast-routing on each of the 4506s and on the 6506. IGMP snooping is on by default on the 3560 and 2960 switches. CGMP is on by default on the 3548 switches.
I set up PIM sparse-dense mode and IGMP version 3 on each of the layer 3 interfaces for the 4506s and 6506 where they connect and on each VLAN that is sending or receiving multicast. Multicast is working throughout the network, however I am looking to verify the configuration as I scale this out to more clients on the network.
#1 - Is it correct to us sparse-dense mode in this configuration?
#2 - Do I need to configure a rendezvous points using AUTO-RP? (ip pim send-rp-announce INTERFACE scope TTL). Not sure here if I need to designate this and what to choose. Right now I do not have this and it is working, but documentation seems to infer that I need to designate this.
#3 - Is there any other configuration settings I should be considering? I hard to find real world configurations of multicast as examples or people that know multicast routing well.
View 3 Replies
View Related
Apr 29, 2012
I would like test multicast routing with cisco1801.i create 2 Vlan. Vlan 200 (192.168.200.x) affect Fastethernet 1, Vlan 130 (192.168.130.x) Fastethernet 5.
Version IOS is : adipservice-k9 124-9.t1
ip multicast-routing
#int Vlan 130
ip address 192.168.130.254 255.255.255.0
Ip pim dense-mode
#int Vlan 200
Ip address 192.168.200.254 255.255.255.0
Ip pim dense-mode
I used VLC for my test.When i connect source (224.10.10.10) and recever ( Udp://@224.10.10.10:1234), that's ok!But, source is on the Vlan 200 and reicever on the Vlan 130, is not good!I test with "sparse-mode", i have same problem.
View 2 Replies
View Related
Feb 21, 2013
I’ve been trying a few days now to implement multicast routing on my home network in order to make airplay work between subnets. Specifically between an iphone and a hifi separated by different vlans. Failed, as I have no experience in multicast routing. we have a clean configuration and simple network which consists of two SVIs
Vlan 10: 192.168.1.0 255.255.255.0
Vlan 20: 192.168.2.0 255.255.255.0
ios platform cisco 887
View 5 Replies
View Related
Jan 17, 2012
while i am configuring a port on switch .The switch reloads.After reload the show version says,System returned to ROM by bus error at PC 0x458F6C, address 0x0,show version from the effected switch is,Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1).
View 4 Replies
View Related
Nov 14, 2011
I faced multicast routing problem - There is no multicast UDP stream toward host, although all igmp Joins/Reports/Leaves from the host are correct.
This is Cisco 7609 ip m route debug showing the situation:
369144: Nov 15 15:03:07.370 MSK: IGMP(0): Received v2 Report on Vlan176 from 10.XXX.XX.184 for 239.XXX.XX.46
369145: Nov 15 15:03:07.370 MSK: IGMP(0): Received Group record for group 239.XXX.XX.46, mode 2 from 10.XXX.XX.184 for 0 sources
[code]....
View 3 Replies
View Related
