Cisco Switching/Routing :: 2960S Multicast Routing

Jan 17, 2012

while i am configuring a port on switch .The switch reloads.After reload the show version says,System returned to ROM by bus error at PC 0x458F6C, address 0x0,show version from the effected switch is,Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1).

View 4 Replies


ADVERTISEMENT

Cisco Switching/Routing :: How To Enable Multicast Routing On 2960s

Mar 23, 2013

I need to enable multicast routing on 2960s but the command "ip multicast-routing" isn't available on my release (12.2.(55)).
 
From which release this command is available?     

View 1 Replies View Related

Cisco Switching/Routing :: 2960S - Multicast Imaging And VLANs

Oct 2, 2012

This is the deal, I used Acronis for imaging workstations.  Obviously when I do that it drags everything down to a halt, as all the ports are being flooded with packets.  So what options do I have to image (as opposed to doing it after hours or try to plug all the computers into one isolated switch? = )
 
VLAN 1 has well everything in it, PXE server, DHCP server and workstationsVoice VLAN 100 is on every trunk or connection a workstation would be attached to.  
  
There is another equipment I'm not illustrating... although a part of me wonders if my topology is correct.
 
In any case, I've read about IGMP Snooping, CGMP, etc-- but I think the 2960S are only capable of IGMP Snooping.
 
And from there I'm a little confused about configuration of IGMP...

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 2960S / Multicast Not Working Between Two Data-centers?

Jan 28, 2012

Multicast is not working between our two datacenter, we have catalyst 2960S (two stacked) as the internal lan switch, and catalyst 3560E as the external switch, same configuration for both datacenters.The two sites are connected using metro, the external switch (3560) is doing qinq and encapsulate the data from the internal switch with the metro vlan (611).
 
IGMP snooping is disabled for all switches, although we prefer to enable it for the internal switches.For each datacenter there is a different firewall which also act as the router, we are using fortigate as the firewall.Following is the important configuration section:
 
Port 43 in the internal switch is connected to the external switch (both sites):
 
interface GigabitEthernet1/0/43 
switchport mode trunk
 load-interval 30 
 
Port 3 in the external switch connected to the internal switch (both sites):
 
interface GigabitEthernet0/3 
switchport access vlan 611
 switchport mode dot1q-tunnel 
no cdp enable
 no cdp tlv server-location
 no cdp tlv app
 
 Port 8 on the external switch connected to the metro link (both sites) vlan 350 is the internet and 611 is the metro:
 
interface GigabitEthernet0/8
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 350,611
 switchport mode trunk  

vlan 611 on external switch:
 
interface Vlan611 
ip address 192.168.168.2 255.255.255.0
 no ip route-cache 
no ip mroute-cache

View 6 Replies View Related

Cisco Switching/Routing :: Why Does Routing Work Without Declaring Vlan10 On 2960s-24td-l

Oct 28, 2012

I have recently split the voice vlan (10) from the data network (1), and am wondering why my catalysts and router do not require an interface Vlan10 statement.  In the past I used OpenBSD boxes to do the routing, and I first needed to configure vlan 10 on the interface before I could get inter-vlan communication to work.  With these Cisco devices it works, and I am wondering if it is because of VTP, for the fact that the ports maybe just pass all traffic, or is there some other explanation?  Below is the setup, and firmware is up-to-date on all of the devices.
 
When I plug a phone into the POE SGE, the phone turns on, obtains an address on the proper subnet, and conversations are clear (whereas without the ip nat inside on the new subnet the calls had a lot of static).  Possibly the reason that it works is because the phones properly create the tcp/ip packet, and it hops over the trunks and creates the states so that traffic routes back properly.  I will install wireshark to see exactly what is going on, but is there a simple explanation that I am overlooking?

View 1 Replies View Related

Cisco Switching/Routing :: 2821 Multicast Routing Relay Basic

Mar 12, 2013

I  start configuring Cisco 2821 router for multicast . First short  description and attached sheme explanation. Let we say  I have small  network with 100 users. One router and Cisco switch 3560. Two VLAN’s,  one for data another for multicast. Data from internet works fine but  now I want to connect multicast servers (or source of more multicast  streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?

First step:  enable multicast routing

Second step: on both interfaces (Fe 0/1 and Fe 0/2)  - ip pim sparse-mode

Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
 
When  I start VLC on computer nothing happend. If I try to connect computer  on same subnet where is source of multicast streams it works fine.What  I am doing wrong ? Is there anything about routing ? All subnets are  directly connected. RP is not needed if I have one router or ?

View 11 Replies View Related

Cisco Switching/Routing :: 6509 - Multicast Routing Preference

Nov 14, 2012

I have a problem on my catalyst 6509 on which I would like to do the following things :
 
I have some Vlans in which multicast is enabled.
In tose Vlan theres is a router which is default router for equipements.
 
I had enabled multicast routing because some Vlan needs to exchange multicast informations, but I wolud like to make difference between Multicast traffic. For example I have 5 vlans:
 
Vlan 1 and 2 need to exchange Multicast informations but the don't need multicast information from Vlan 3 and 4
Vlan 3 and 5 need to exchange Multicast informations but the don't need multicast information from Vlan 1 and 2
Vlan 5 is independant Vlan but doesn't need to have multicast information from all others vlan.
 
Last problem, equipement on differents vlan can use the same Mulkticast group address. In this case, Multicast routing is not working between Vlan 1 to Vlan 2 and Vlan 3 to Vlan 4.

View 6 Replies View Related

Cisco Switching/Routing :: 4506 / 6506 - Multicast Routing

Mar 8, 2013

I am configuring multicast in a environment where I have a 4506 at each site (4 total) and a 6506 as the core. Each 4506 is connected via layer 3 to the 6506. I have a mix of 3560s, 3548s, and 2960s connected to the 4506s and the 6506 via layer 2 trunk
 
I have multiple multicast sources and hosts communicating at a time (multiple cameras sending video / multiple computers receiving video).  So this is not a scenario where there is 1 sender and many receivers.  This would be many senders (~50) and some receivers (~10)
 
Sample Diagram:
 
->3560
|
6506 --> 4506 --> 3548
|   |
|    --> 2960
|
4506 --> 2960
|
-->3548
 
I configured ip multicast-routing on each of the 4506s and on the 6506. IGMP snooping is on by default on the 3560 and 2960 switches. CGMP is on by default on the 3548 switches.
 
I set up PIM sparse-dense mode and IGMP version 3 on each of the layer 3 interfaces for the 4506s and 6506 where they connect and on each VLAN that is sending or receiving multicast. Multicast is working throughout the network, however I am looking to verify the configuration as I scale this out to more clients on the network. 
 
#1 - Is it correct to us sparse-dense mode in this configuration?
 
#2 - Do I need to configure a rendezvous points using AUTO-RP? (ip pim send-rp-announce INTERFACE scope TTL). Not sure here if I need to designate this and what to choose.  Right now I do not have this and it is working, but documentation seems to infer that I need to designate this.
 
#3 - Is there any other configuration settings I should be considering?  I hard to find real world configurations of multicast as examples or people that know multicast routing well.

View 3 Replies View Related

Cisco Switching/Routing :: Test Multicast Routing With 1801?

Apr 29, 2012

I would like test multicast routing with cisco1801.i create 2 Vlan. Vlan 200 (192.168.200.x) affect Fastethernet 1,  Vlan 130  (192.168.130.x) Fastethernet 5.

Version IOS is : adipservice-k9 124-9.t1

 ip multicast-routing
 
#int Vlan 130
  ip address 192.168.130.254 255.255.255.0
  Ip pim dense-mode
#int Vlan 200
  Ip address 192.168.200.254 255.255.255.0
  Ip pim dense-mode
 
I used VLC for my test.When i connect source (224.10.10.10) and recever ( Udp://@224.10.10.10:1234), that's ok!But, source is on the Vlan 200 and reicever on the Vlan 130, is not good!I test with "sparse-mode", i have same problem.

View 2 Replies View Related

Cisco Switching/Routing :: 887 - IP Multicast Routing Between Subnets Same Router

Feb 21, 2013

I’ve been trying a few days now to implement multicast routing on my home network in order to make airplay work between subnets. Specifically between an iphone and a hifi separated by different vlans. Failed, as I have no experience in multicast routing. we have a clean configuration and simple network which consists of two SVIs

Vlan 10: 192.168.1.0 255.255.255.0
Vlan 20: 192.168.2.0 255.255.255.0
 
ios platform cisco 887

View 5 Replies View Related

Cisco Switching/Routing :: 7609 - Multicast Routing

Nov 14, 2011

I faced multicast routing problem - There is no multicast UDP stream toward host, although all igmp Joins/Reports/Leaves from the host are correct.
 
This is Cisco 7609 ip m route debug showing the situation: 
369144: Nov 15 15:03:07.370 MSK: IGMP(0): Received v2 Report on Vlan176  from 10.XXX.XX.184 for 239.XXX.XX.46
369145: Nov 15 15:03:07.370 MSK: IGMP(0): Received Group record for  group 239.XXX.XX.46, mode 2 from 10.XXX.XX.184 for 0 sources
[code]....

View 3 Replies View Related

Cisco Switching/Routing :: 2960S And MLS QoS Map

Oct 8, 2012

I have C2960S-48FPS-L and C2960S-24TS-S both of them are using C2960S-UNVERSALK9-M image with version 15.0(2)SE on both I run "mls qos"
 
and on 48FPS-L I run "mls qos map cos-dscp..."on 24TS-S I cannot run it. there is no such command. there is just "mls qos rewrite..." and "mls qos srr-queue..." variants. 
 
I thought that one image give the same set of commands...?

View 5 Replies View Related

Cisco WAN :: Multicast Routing Between Vrf (Cat 3750) - Multicast Vpn Extranet?

Feb 19, 2013

I try to pass multicast traffic between two vrf on the same 3750 switch. I have IP services IOS and sdm template routing.
 
here is my config:
 
ip routing
!
ip vrf vpn2
rd 1:1
mdt default 232.1.1.1
route-target export 1:1
route-target import 1:1

[code]....
 
Now I'm stuck - I don't know what to do to pass multicast traffic. Do I have any chance to run this config on 3750 chassis?Perhaps "Configuring Multicast VPN Extranet Support" document will be useful, but it concerns Catalyst 6500? [URL]

View 0 Replies View Related

Cisco Switching/Routing :: STP Between 2960S And SG300

Dec 8, 2011

I am currently having an issue with connecting a Catalyst 2960-S switch to a Small Business SG300 switch. When I connect them they are unable to form a link. When I do a show spanning-tree it says the mst link is in dispute.

View 1 Replies View Related

Cisco Switching/Routing :: 2960S QoS For VoIP?

Mar 25, 2012

I read some papers about QoS. The thing is that I have to implement 30 switches with QoS to connect to a lot of Cisco IP phones. The switches are Cisco 2960S with code image "C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3". Should I use autoQoS feature or manually configure them?. How should I treat uplinks between access switchs and core/distribution? I have a lot of doubts regarding queueing, because all the info I had read its for another model/image.

View 4 Replies View Related

Cisco Switching/Routing :: Mix 10G And 1G Uplinks On 2960s?

May 16, 2013

I'm looking at the WS-C2960S-48TD-L and have a question about the uplink ports. Is it possible to mix 10G on one uplink and 1G on the other?  The datasheet says 2x10G SFP+, 2x1G SFP so I am thinking mixing is not possible.

View 6 Replies View Related

Cisco Switching/Routing :: How To Use USB Option On 2960s

Nov 5, 2011

just got new hardware and decided to try the newer USB port for IOS upgrades. I could not get the switch to recognize my 2gig flash drive. Do I need a proprietary stick or special format?

I also noticed when I removed it the switches crash dump and rebooted?

View 12 Replies View Related

Cisco Switching/Routing :: Multicast On Subinterface On 861?

Feb 7, 2013

I have an 861 that we are using for a test network and need to add static igmp addresses for multicast.  We are using the router as a router on a stick with subinterfaces on the WAN link.  I've looked everywhere to see how to add the static igmp addresses.
 
interface FastEthernet4
no ip address
no ip route-cache cef

[Code]....

View 0 Replies View Related

Cisco Switching/Routing :: NTP Multicast On 3750?

Dec 10, 2012

I have a subnet with a GPS clock on it that connects into a Cisco 3750. The 3750 has another subnet hanging off of it that connects into a firewall then to a server. I need the server to get time from the GPS clock. Any way to pass the NTP through the 3750?  The 3750 has the 3750-IPBase code running on it so the multicast support is limited. I am under regulatory restrictions that only allow traffic to flow from the higher security level (were the time server is) to lower security level (were the server is). This prevents me from having the server go to the clock for updates.

View 1 Replies View Related

Cisco Switching/Routing :: Can RPS2300 Support 2960S

Aug 18, 2012

When using dynamic configuration tools, if I choose 2960 (not 2960s), I have the option to choose RPS2300 as redundant power, but when I choose 2960s, I cannot choose RPS2300. However, in a document describe both 2960 and 2960s, it said that RPS2300 can be used. Does RPS2300 support 2960S?

View 1 Replies View Related

Cisco Switching/Routing :: 2960S QoS Configuration Not Work

Dec 20, 2012

Recently I'm working with my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply)  Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET,This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.Access-list 100 permit ip any any dscp default,class-map match-all QoS_Floor_Limit, match access-group 100.

View 1 Replies View Related

Cisco Switching/Routing :: Stack 4900M With 2960S?

Mar 11, 2013

I would like if is possible to stack a Cisco 4900M with a 2960S. I know it is not the most common situation but i need it.

View 1 Replies View Related

Cisco Switching/Routing :: 2960S MAC Address Control

Feb 20, 2013

I would like to enable port security to hardcode the MAC address on the ethernet switch. There are 5 ethernet ports in the same ethernet switch to be assigned for one person (one note book), e.g. port 5, 6, 15, 16 and 23. The model of ethernet switch is cisco 2960S and one MAC address is configured on 2960S.
 
1. Does 2960S support this requirement to allow input the same MAC address to 5 different port?

2. If yes, can ethernet switch "smart" enough to forward the packages to "active" ethernet port which is connected to notebook and the rest of four ports are inactive.

3. if no, any solution or any work around to achieve this requirement 

View 5 Replies View Related

Cisco Switching/Routing :: 2960S / LAN Design Using 10G EtherChannels?

May 11, 2011

We are designing a LAN Network for ourselves.The proposed design is as follows:
 
4 x 2960S switches in a Stack   Access-Stack-I 4 x 2960S-PoE switches in a second Stack Access-Stack-II
 
2 x 3750X switches in a Stack   Core-Stack
 
Now I would like to connect it in the following manner ?First,I would like to use EtherChannel using the 10Gig LinksSecondly, I would like to use Cross-Stack EtherChanel too.I have given a graphical illustration of the connectivity Now my Qs: a) Will the 2960S supports EtherChannel using the 10G links and the 3750X too... b) Does the proposed solution will work... or It will have any problems.

View 4 Replies View Related

Cisco Switching/Routing :: 2960S Cannot See VLAN100 Traffic On SW1

Jan 29, 2013

I have two switches (2960S's) both with IP Phones on VLAN100..We need to monitor voice traffic via a monitor port on SW1 of all VLAN100 traffic on both switches.The following is what we have configured, but we cannot see VLAN100 traffic on SW1
 
According to Cisco doco you cannot have a SPAN and RSPAN on the same session, however since these are two sessions on SW1, I would have thought it to be OK.

View 4 Replies View Related

Cisco Switching/Routing :: 2960s / Add One More Switch In Stack?

Apr 29, 2013

I have a running setup having 2 Cisco 2960s 24 TS switch with Stack configuration. Now I want to add one more same Cisco switch. My questions are:-
 
1) How can I do this...(Should follow the same process as I did before.

2) Could I do this without impacting the service. i.e. without rebooting the switch.

3) What should be the connection archiecture as of now since there is two switch so it is connected 1 -1 and 2-2. but for 3 switch should we require to change the connectivity.

View 1 Replies View Related

Cisco Switching/Routing :: Dscp Marking In 2960S

Jul 21, 2012

i did on cisco 2960S switch at user ingress interface. but the marking is not showing in show policy-map interface gig 1/0/10 interface and ACL is not showing any match.
 
I also had a config reference from 2960S cisco guide.
 
access-list 103 permit tcp any any eq 80
access-list 104 permit tcp any any eq 23
access-list 105 permit icmp host 172.24.68.4 any
 
class-map IN_HTTP
match access-group 103

class-map IN_TELNET
match access-group 104(code)

View 1 Replies View Related

Cisco Switching/Routing :: High CPU Utilization On 2960S?

Feb 8, 2011

We have seen high CPU utilization on some Cisco switches of type 2960S. Also we got info, that applications are running with poor performance or with interruption.Following IOS is loaded: C2960s-universalk9-mz.122.55.SE

View 9 Replies View Related

Cisco Switching/Routing :: Dynamic Bandwidth On A 2960S?

Dec 20, 2012

They have a /28 wan adress coming from ISP, that gives out 100Mbps, going to a Cisco 2960S switch (ver. 12.2) the switch is only holding 1 vlan. Connected to the 2960 are 3 firewalls/routers from other manifactors, each creating their own network. The customer wishes for a solution where each final FW/router gets minimum 33% and maximum 100% of the bandwidth, depending on how much each final Fw/router are in use.

View 1 Replies View Related

Cisco Switching/Routing :: Stack 4900M With 2960S?

Mar 11, 2013

I would like to know if i can and how stack a Cisco 4900M with a 2960S. I know it's not the most common but i need it.

View 2 Replies View Related

Cisco Switching/Routing :: Information About PoE Of Switch 2960S

Jan 21, 2013

I use the Switch 2960S support PoE and 10 access points cisco.I have one more question:
 
-- If all 10 access points cisco use copper cable to connect to 2960S, 5 access points use power adapter and 5 access points use power from Switch. How Switch 2960S will provide power for 10 AP or switch 2960S will understand and only provide power for 5 APs?

View 3 Replies View Related

Cisco Switching/Routing :: Stack 2960s Not Full

May 7, 2013

I have 4 switchs 2960s in stack, but this not full ring. [code]the interface stack 1 for switch 1 is down and interface stack 2 for switch 4 is down.I do  insert this command "switch 1 stack port 1 enabled" but interface are not up.

View 4 Replies View Related

Cisco Switching/Routing :: Multicast On 886VA VLAN?

Oct 28, 2012

I'm trying to configure multicast between 2 VLANs on a Cisco 886VA running IOS 15.2 (3) T1 (advanced security). While I can set the global "ip multicast-routing" I cannot "ip pim sparse-mode" on my interfaces - ip pim is actually unknown and also doesn't appear in the interface's ip subcommand list when using "?".
 
The feature navigator says pim is supported on my platform and IOS version.
 
My config looks like this:
 
interface FastEthernet3
switchport access vlan 103
no ip address

[Code].....

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved