Cisco Switching/Routing :: Configuration Multicast Packet Forwarding On 3750?
Mar 3, 2013
I have one server which run some application for wireless user. this server forward multicast packet to wireless user. server and wlc physically connect to cisco 3750 switch.i want the server forward the multicast packet to wireless users.server access vlan 4.wlc controller have 2 vlan: 90 and 110.and wireless user some of vlan 90 and some of vlan 110.i enable igmp snooping on wireless controller. and enable globally command but it is not working.which additional configuration i need on cisco switch.
Switch(config)# ip igmp snooping
View 16 Replies
ADVERTISEMENT
Dec 10, 2012
I have a subnet with a GPS clock on it that connects into a Cisco 3750. The 3750 has another subnet hanging off of it that connects into a firewall then to a server. I need the server to get time from the GPS clock. Any way to pass the NTP through the 3750? The 3750 has the 3750-IPBase code running on it so the multicast support is limited. I am under regulatory restrictions that only allow traffic to flow from the higher security level (were the time server is) to lower security level (were the server is). This prevents me from having the server go to the clock for updates.
View 1 Replies
View Related
Feb 19, 2013
I try to pass multicast traffic between two vrf on the same 3750 switch. I have IP services IOS and sdm template routing.
here is my config:
ip routing
!
ip vrf vpn2
rd 1:1
mdt default 232.1.1.1
route-target export 1:1
route-target import 1:1
[code]....
Now I'm stuck - I don't know what to do to pass multicast traffic. Do I have any chance to run this config on 3750 chassis?Perhaps "Configuring Multicast VPN Extranet Support" document will be useful, but it concerns Catalyst 6500? [URL]
View 0 Replies
View Related
May 12, 2013
I've been handed a requirement to try and get a multicast server working on my setup. Trouble is, I don't know if I can with the feature set I have on my switches. What is desired is that a multicast server (stand alone, but network connected, obviously) be accessible by everyone on the local network (multiple V LAN's, multiple SVI's) in the building.
All users will be connected to the one switch stack, although some will want to be wireless (which is one of the separate V LAN's) - I don't care if the wireless requirement goes by the wayside - they can sod off. :-) The main purpose will be multicast, high quality video.
I have a single switch stack consisting of two (soon to be 3) WS-C3750X-48P switches running the IP BASE feature set.
Question - can I do this on IP BASE, or do I need to upgrade to IP SERVICES?
If I can do it on IP BASE, does anyone have any links/pointers to setup this properly? Currently installed IOS is 12.2(58)SE2.
View 3 Replies
View Related
Apr 16, 2013
I have PC_A and PC_B connected to the same switch, and are put in the same vlan. PC_A is the master (source) and PC_B is the destination (client). IGMP Snooping is enabled by default.
Is there any reason why this should fail? There is no RP or any interface with PIM enabled. Its a flat network with a source and client in the same vlan...
IH-3750-LOADTEST-101#show ip igmp snooping vlan 724
Global IGMP Snooping configuration:
-------------------------------------------
IGMP snooping : Enabled
[Code].....
View 19 Replies
View Related
Jun 19, 2012
A multisite network is currently supporting muticast using PIM dense mode, which is enabled on router/switch LAN and WAN interfaces across all locations. I am about to introduce Nexus switches to the main LAN. How can I make dense and sparse mode coexist to ensure flow of muticast traffic between devices supporting and dense and sparse mode? Eventually, I want to transition to the sparse mode; however, it has to be done gradually, even within a single site. The leacy equipment includes Cat 3750 and 4500s.
View 2 Replies
View Related
Mar 5, 2013
our C3750 like the one described here [URL]
We have the port on the switch set like this:
switchport port-security maximum 25
switchport port-security
switchport port-security aging time 2
switchport port-security violation restrict
switchport port-security aging type inactivity
In case a device connected to the port is inactive for more than 2 minues ( aging time ) the first frame/packet the device generates arrives to the port on the switch, but the switch does not forward it to the appropriate port ( discards it or whatever ).
So far I tested on
1 30 WS-C3750E-24PD 15.0(2)SE2 C3750E-IPBASEK9-M
2 30 WS-C3750E-24PD 15.0(2)SE2 C3750E-IPBASEK9-M
3 52 WS-C3750G-48PS 15.0(2)SE2 C3750-IPBASEK9-M
[Code].....
When we remove port security from the port, it works perfectly fine, as expected.
It seems this is not HW or IOS version related. It seems it is not a stack synchronization issue, it does not matter if a device is connected to the first or other stack member. I tested on C3560 too, here there are no problems, so seems it is 3750 related.
View 1 Replies
View Related
Dec 15, 2011
I have a non-cisco router with a public WAN address. This is conencted to a 3750 switch internally. The switch is the default gateway for all VLANs, and the gateway router has static routes back to the 3750. The Router provides NAT, no NAT is done on the switch.My requirement is to port forward port 29 000 so that I can access a server on VLAN4 via this port.
So, I have: Router: Port 29000 map to 192.168.4.1 (Switch VLAN4 address)
The question is, how do I route port 29000 from the 3750 to the server on 192.168.4.42 ? what exactly I should add in order to port forward port 29000 incoming form my router, to my server on 192.168.4.42.
View 17 Replies
View Related
Nov 6, 2012
I have a 3750 catlyst switch in my network and it is like a distubation switch,And for the nating and dhcp nomadix is using as gateway in the same network. for one of my local PC i need to config the port forwarding in 3750 switch. How to config the port forwarding on 3750 switch,
View 3 Replies
View Related
May 23, 2012
i have made a topology in packet tracer related to etherchannel configuration.i am using 2 3560 switches and 1 2950 switch. Now what i want is to bundle up the redundant links between these 3 switches. The links fa0/1-3 between 2950_1 and 3560_1 switches have been bundled up but when i try to bundle the links fa0/4-6 of 3560_1 to fa0/4-6 of 3560_2 it wont work. i am using channel-group 1 mode desirable between the 3560 switches. secondly if i want to assign ip to port channels then it has to be of same subnet between 2 3560 switches right and it must be same between 2950_1 and 3560_1. But these 2 subnets should be different from one another.
View 3 Replies
View Related
Jun 26, 2011
I can't seem to find where in ASDM (6.4.1), can we configure IGMP forwarding? ASA5520(config-if)# igmp forward interface outside The ASDM doc reference does not seem to be correct pointing to:configuring Stub Multicast Routing
Step 1 In the main ASDM window, choose Configuration > Device Setup > Routing > Multicast > IGMP.
#Step 2 In the Multicast pane, check the Enable Multicast routing check box.
#Step 3 Choose MForwarding.
which generates:
ASA5520(config-if)# mfib forwarding
View 4 Replies
View Related
Mar 19, 2012
i have linksys modem which already running for differents vlans i cerated another different vlans 10 amd 20 for 10 and 20 i need internet how should i configure internet on another core switch3750
View 0 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
Jan 28, 2012
We have a few stacked 3750 switches with vtp transparent configured...some plugged in a fiber from another network into our stacked switches...that network/switch has vtp server configured...once that switch connected to our stack of switches, it turned that stack switch into vtp server...causing the previous vlans configured to erase thus causing management issues with the stacked switches..
View 4 Replies
View Related
Feb 17, 2013
seeking for configuration assitance on etherchannel between catalyst 3750 and 6506
View 3 Replies
View Related
Dec 31, 2011
I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control). I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8 (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.
View 5 Replies
View Related
Jul 3, 2012
I have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.
Network Diagram:
switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1
[Code]....
View 8 Replies
View Related
Jul 16, 2012
Our servers are hosted at the Main site, site office A access to the Main site for Internet and servers. We are thinking NextG to take over when the link between sites goes down.
To start with, what is the configuration for 3750 at Site A and the Main site:
1) Trunking for both switches
2) Routing
3) the automatic failover configuration for the switch at Site A.
View 1 Replies
View Related
Apr 17, 2012
I am uploading new configurations to my Cisco 3750 stacked switch and noticed that after the load I cannot log back into the switch because my password somehow was changed. After performing password recovery and getting back into the swtch, I noticed the configuration register was 0xF. I have never seen this before. The config-register command does not seem to be supported to change it back to factory default. The switch is on a ship which has several power hits when they switch power from shore to ship power.Can this cause the configuration register to change? What is the best way to change the configuration register?
View 1 Replies
View Related
Jul 26, 2012
I'm fairly new at trying to create isolated network segments on Cisco switches. What I'm trying to do is have multiple isolated paths that originate from my v Sphere infrastructure travel through a layer 2 link, v LAN, up to a MLS, and ultimately out to to the internet through a firewall. Each sub net might ultimately have a number of hosts on it, but I don't think the make up of those hosts will matter here.
My initial thought was creating v LAN tagged port groups on v Switches on my v Sphere infrastructure. Physical connections will go from my ESXi hosts to the 2900 series Cisco switch connected to trunk ports. Both v LANs would be configured on the switch but not assigned to physical ports. The physical connection to the 3750 would also be a trunk port connection from the 2960. The 3750 would have SVI's created that are attached to VRFs that would control route traffic. This might be totally wrong but from what i've read it seems to be going down the correct path I think.
Two part question, is this the best way to go about designing this network? If so I seem to be really struggling with the SVI/VRF part. Every time I create an SVI all of my hosts on the 10.10.10.x network can ping them, regardless of which v LAN they're on.
I just cannot seem to isolate the 172 network.
View 3 Replies
View Related
May 23, 2012
I'm trying to configure a mirror port on a 3750. This configuration needs to replicate data from local ports, but I need that also act as a regular access port.
With the initial configuration, SPAN port, there is no problem, all the data of the configurated ports is replicating in the configurated port. On the port configurated as mirror there is a PC connected for audio recording. When the port is not operating as SPAN there is communications without problem over the LAN. But when I configure the port as SPAN, communication is interrupted.
Here is the actual configuration:
SWITCH1-PISO7#sh monitor session 1
Session 1
---------
Type : Local Session
[Code]......
View 5 Replies
View Related
Feb 27, 2013
I am building a new network and intended on using the min-link feature on my port-channels between a 3750-X series switch and Nexus 4k.
However reading further into this it seems this feature is only supported on higher end models. I cannot find any reference to the min-links feature in the 3750-X configuration guide. Is this an available feature?
The 3750-X model is WS-C3750X-24T-L running IOS 12.2(55)SE3 IP Services
My thoughts is that the is only an LACP supported feature so I may not see the command until I have entered an LACP specific command on the port-channel but unfortunately I do not have a 3750X to verify this on at present.
View 0 Replies
View Related
Dec 20, 2012
I have stack of 2 switches 3750?I config etherchannel between them.
here is result
2 Po2(SD) LACP Fa1/0/15(I) Fa2/0/15(I)
Both ports are up up but standalone Int port channel 2 is down down.Need to know if this is default behaviour when we config etherchannel between stack switches?
View 2 Replies
View Related
Mar 6, 2013
I have a 2911 router connected to a 3750 switch. I have configured vlan interfaces on the 2911 router:I am using the vlan 89 (89.2) as the management ip address for me to remotely get to the switch. Is this a proper configuration or could this cause issues in the future.
View 4 Replies
View Related
Dec 13, 2011
boot system switch all flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin We have two stack of 3750 switches. When I enter above command getting below mentioned error, two images are showing switch 1, but one image only showing in switch 2, i.e 1st image in show boot command.
%Command to set boot system switch all flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin on switch=2 failed
View 5 Replies
View Related
Dec 4, 2011
How do I create static smartport macro on Catalyst 2960 & 3750 equivalent to below static smartport macro:
macro name NOT_USED
description UNUSED_PORT
switchport
switchport mode access
switchport access vlan 100
shut
@
I am able to create above smartport macro on Catalyst 3760 & 6500, but not on 2960 & 3750 (see below):switch(config)#macro ? auto Macro autoexecution settings global Enter global macro configuration
View 12 Replies
View Related
May 29, 2013
Since Avaya phones do not run CDP, how does the phone know which DHCP pool to pull from to get its IP address if the PC is connected to the phone.
Let's say I have a interface config like this
interface gigabitethernet1/0/1
cisco3750(config-if)#switchport mode trunk
cisco3750(config-if)#switchport access vlan 126
[code]....
And two DHCP scopes configured on the switch. What keeps the phone from pulling from the wrong scope?
View 2 Replies
View Related
Sep 16, 2012
I'm trying to configure scp for secure configuration backup. I've configured the SCP server with an account and password but, I keep getting the no such file or directory error
AP-C2R1C5-3750#sh run | b arch archive path scp://mchenry:PASSWORD@172.20.22.229//C:/Program_Files/OpenSSH/Cisco_Configs/Switch_Config
username mchenry privilege 15 password 7 XXXXXXXXXXXXXXXXXXXXX
ip scp server enable
Error: %scp: /C:/Program_Files/OpenSSH/Cisco_Configs/Switch_ConfigSep-17-16-04-44.172-1: No such file or di
SWITCH#ping 172.20.22.229 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 172.20.22.229, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 33/33/34 ms
View 1 Replies
View Related
Nov 14, 2011
3750 switch connects to Blade-switch_1 and Blade-switch_2 Spanning-tree mode is configured as rapid-pvst on 3750 switch, do I need to configure rapid-pvst on both blade-switches or keep the default pvst config.3750 is running VTP domain HQ and transparent mode Both Blade_switches are running VTP domain CLI and transparent mode To configure Etherchannel between 3750 and blade-switch_1 do I need to have all devices in same vtp domain?
View 16 Replies
View Related
Mar 12, 2013
I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
First step: enable multicast routing
Second step: on both interfaces (Fe 0/1 and Fe 0/2) - ip pim sparse-mode
Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
When I start VLC on computer nothing happend. If I try to connect computer on same subnet where is source of multicast streams it works fine.What I am doing wrong ? Is there anything about routing ? All subnets are directly connected. RP is not needed if I have one router or ?
View 11 Replies
View Related
May 15, 2010
Upgrading the firmware from 1.11EU to 1.21EU and 1.31EU has introduced a problem with multicast (IPTV) streams. I have enabled multicast streams and it seems the router no longer forwards a specific address range, in my case 239.139.128.* on port 1234.
I have checked: Streaming from 233.81.233.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 24.1.3.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 239.139.128.* works only in 1.11EUUsing IGMP proxy on Linux I have checked the stream at 239.139.128.* are available as to be sure the DIR-655 is not forwarding them. I see a lot of forum messages stating IPTV streaming is broken since firmware 1.11. It is however working for me in 1.31EU but only for certain address ranges. Can anything be configured to allow 239.139.128.* to work? Because my TV provider uses the 239.139.128.* range for half the IPTV channels I need to get this working.
Related to this, is there page listing known bugs for the DIR-655 and roadmap for future firmware releases?
View 2 Replies
View Related
Mar 23, 2013
I need to enable multicast routing on 2960s but the command "ip multicast-routing" isn't available on my release (12.2.(55)).
From which release this command is available?
View 1 Replies
View Related
Nov 14, 2012
I have a problem on my catalyst 6509 on which I would like to do the following things :
I have some Vlans in which multicast is enabled.
In tose Vlan theres is a router which is default router for equipements.
I had enabled multicast routing because some Vlan needs to exchange multicast informations, but I wolud like to make difference between Multicast traffic. For example I have 5 vlans:
Vlan 1 and 2 need to exchange Multicast informations but the don't need multicast information from Vlan 3 and 4
Vlan 3 and 5 need to exchange Multicast informations but the don't need multicast information from Vlan 1 and 2
Vlan 5 is independant Vlan but doesn't need to have multicast information from all others vlan.
Last problem, equipement on differents vlan can use the same Mulkticast group address. In this case, Multicast routing is not working between Vlan 1 to Vlan 2 and Vlan 3 to Vlan 4.
View 6 Replies
View Related
