I have a 3750 catlyst switch in my network and it is like a distubation switch,And for the nating and dhcp nomadix is using as gateway in the same network. for one of my local PC i need to config the port forwarding in 3750 switch. How to config the port forwarding on 3750 switch,
View 3 RepliesI am in the process of setting up an interop lab for some engineers. The enviornment will consist of some 3750's, H3C's and ProCurves. My concern is that the end user will have Priv-Exec access for CLI usage on the 3750's and they can change the "en" password (I hope they don't but it has happened).Is there a way I can "break in" during the boot process to reset the password? The reason I am doing it this way is because I have an Altiris server with rebuild automation scripts in xpect and I would like to automate the process so I do not have to use a manual factory default reset.
View 5 Replies View RelatedI have a non-cisco router with a public WAN address. This is conencted to a 3750 switch internally. The switch is the default gateway for all VLANs, and the gateway router has static routes back to the 3750. The Router provides NAT, no NAT is done on the switch.My requirement is to port forward port 29 000 so that I can access a server on VLAN4 via this port.
So, I have: Router: Port 29000 map to 192.168.4.1 (Switch VLAN4 address)
The question is, how do I route port 29000 from the 3750 to the server on 192.168.4.42 ? what exactly I should add in order to port forward port 29000 incoming form my router, to my server on 192.168.4.42.
I have a WS-CE520-8PC Switch. I have tried a full 30/30/30 reset, factory reset, and I am still unable to access the express setup page. Running Win7 x64 on the host os (have tried windows 2000 and xp)It also wont allow me to access direct managment mode when pressing the admin button for 10 sec.
View 2 Replies View RelatedThere 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it: [code] Switch is Catalyst 3750 with IOS version 12.2(58)SE1.
View 1 Replies View RelatedI have a stack with a lot of stack-port changes, but on all the ports, how can I determine the faulty switch in the stack, cables are already verified. We did also a restart of the whole stack power off/on
running version
WS-C3750-48P 12.2(55)SE C3750-IPBASEK9-M
This is the output after 6weeks
Switch#/ Stack Neighbor Cable Link Link Sync # In Port# Port Length OK Active OK Changes Loopback Status To LinkOK -------- ------ -------- -------- ---- ------ ---- --------- -------- 1/1 OK 4 1
[Code].....
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedI'm trying to setup a port on a catalyst 3750 so it will pass traffic for 2 vlans. It connects to a (watchguard) firewall which I've configured with a primary IP (for vlan 27) and a secondary IP (for vlan 29).
However I can't seem to find the correct commands to enter on the cisco switch port (I've tried a variety).
FYI the current configuration is...
interface FastEthernet1/0/38
description ## Connection to WG vlan27 and vlan 29 ##
switchport trunk encapsulation dot1q
[Code].....
We have QoS configured throughout the company, but the standard config we have applied across the 3750 switches only includes the below: We have IP phones (not cisco) attached that are marking with EF, and the PC is an untrusted end device (so needs to be by default marked as zero).Is the above enough to trust VOIP DSCP EF without resetting it to DSCP 0, or do I also need to add a trust line (i.e.: mls qos trust dscp)?
View 2 Replies View RelatedI would like to know how many port channel can i configured in the switch 3750 X ? and if there is a limitation by IOS ?
View 4 Replies View RelatedIf i fully populate all switch port (Cisco 3750 series) with 100 filter list on each port is it recommendable.
View 4 Replies View RelatedI have one 12-port 3750 switch having one gig connectivity with ASR-9010 router having IOS-XR. I am not able to ping this link with 9000 mtu size. I have enable system mtu jumbo on switch to 9000 and on ASR router interface mtu is set to 9114. At switch side switch interface is configured as a trunk port and one vlan has been passed on that interface. I am not able to ping the ip 172.16.10.2 with 9000 mtu size.
View 6 Replies View RelatedSince Avaya phones do not run CDP, how does the phone know which DHCP pool to pull from to get its IP address if the PC is connected to the phone.
Let's say I have a interface config like this
interface gigabitethernet1/0/1
cisco3750(config-if)#switchport mode trunk
cisco3750(config-if)#switchport access vlan 126
[code]....
And two DHCP scopes configured on the switch. What keeps the phone from pulling from the wrong scope?
We have a cisco 3750-48 port switch.We have a few SVI's configured and some static routes configured.I had created a new interface vlan and gave it an IP. I can ping the gateway.
Now I want to add a static route to go out that interface.when I add: ip route 10.x.x.x 255.255.255.0 10.52.10.1
it eccepts it (no errors) But, it does not show in the routing table nor in the config? How to add the static route to go out that vlan interface.
Any method of forcing a non connected switch port LED to blink for a certain number of times regardless if there is anything connected.The purpose of this is we have remote 3750 switch stacks and quite often have to tell non technical staff to patch to a certain port. It would be much easier if we could say "Connect it to the empty port which just started blinking orange" as the port numbers are difficult for them to see in these locations.A similar feature is available in the ethtool package for linux which makes it really easy for identifying ports on servers. It would be great if a similar feature is available on Cisco switches.
View 2 Replies View RelatedWhat the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?
View 3 Replies View RelatedI have 2 x 3750 stacked, the port number of the master switch is gigabitEthernet2/0/1, slave as gigabigEtherent1/0/1.
Can I change the port numbering so that the master switch gets GigabitEthernet1/0/x?
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
I have been given 2 3750 switches and need to put a config onto it wuld is for 2 3750's in a stack, how should I put this on the 2 switches? Is it bested to install it onto 1 switch first then physically attach the 2nd after?
View 3 Replies View RelatedWe have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
I'm in the process of configuring QOS on a 3560 routing switch in a GOLD, SILVER, BRONZE priority type scenario.
Firstly, I understand that this config will add a tag of "precedence 5" to a packet if it matches the "ACL_QOS_GOLD_In" access list. Question is does the router see this "precedence 5" tag and then sets the priority, or am I missing something in my config where at present it just sees the "precedence 5" and doesn’t act on it ?
Secondly, Since the "precedence 5" tag has already been added to the packets, do downstream routers see this tag and act accordingly or so I need to configure those is well ? [code]
I was trying to configure an SF 300-24 for use in my home and obviously did something dumb. It was working fine. The f/w was updated and I had configured 2 VLANs. VLAN2 was ports 1-6+GE1 for IPTV streaming and VLAN3 was ports 7-24+GE2 and GE3 for the rest of my LAN. I was plugged into GE4 and was configuring the switch with a laptop. GE4 was the only port still on the default VLAN1. I chaged the default VLAN to VLAN3, which forced a reboot and the switch never came back up. Attached is what I see when I connect to the console port: [code]
I can't access to GUI using it's static IP or it's default IP on any port and the console never reaches the point where I can log in. The System light is flashing green but the boot sequence never progresses past what's in the screen shot. I tried to do a hard reset using the recessed button on the front panel but it does not seem to have any effect, no matter how long I hold it down.
I uploaded a new config file via TFTP to a 3560 switch. What are the order of commands to get it to boot from this new config file instead of the file listed in 'sh boot': [code]
View 7 Replies View RelatedI am having difficulties saving, loading conifg files from a USB, what is the correct command for loading a config file from USB for cisco 3750x switch.
View 1 Replies View RelatedI have 2 cisco 6500 in a VSS configuration , All of my Lan access switches are Stack switches and every Stack is connected to the VSS in a Port-channel so basically this is a loop free environment with no blocked ports .As a best practice I left STP in the Background (mstp)which enhanced cisco features to STP should I configure on the Aggregator (6500-VSS) and on the Access switches ?
Because of my topology I dont see the need in configuring most features like Uplink Fast and Backbone Fast but I have configured Loop Guard in addition to UDLD on the 6500 Aggregation Switches (on the port-channels).On the access ports I have configured portfast , bpduguard and guard root (seems a little pointless to configure the two...)
1.should I Leave UDLD on and get rid of LoopGuard and configure Guard root instead ? since LoopGuard cannot be configured with Guard Root.
2.should I configure GuardRoot on access ports if I already have BpduGuard on them ?
3.Is there anything I need to configure on the physicall interface or is everything configured on the port-channel since STP reguards port- channel as a single interface ?
I have one server which run some application for wireless user. this server forward multicast packet to wireless user. server and wlc physically connect to cisco 3750 switch.i want the server forward the multicast packet to wireless users.server access vlan 4.wlc controller have 2 vlan: 90 and 110.and wireless user some of vlan 90 and some of vlan 110.i enable igmp snooping on wireless controller. and enable globally command but it is not working.which additional configuration i need on cisco switch.
Switch(config)# ip igmp snooping
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedI have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedI am trying to configure interface vlan1 to get an ip address from dhcp by entering the commnad ip address dhcp ios rejects the dhcp portion of my command as not recognised although it is referred to in Cisco manuals.my IOS version is c2950-i6k2l2q4-mz.121-22.EA14.bin.I get the same problem when I try to configure ip http secure-server on the switch. Is this a known bug or whether I have the correct IOS version for these commands?
View 6 Replies View RelatedI have my Cisco 881 router up and running, routing all traffic on my small network. I am wanting to utilize port forwarding to enable FTP (forward port 21). All docs I have found say you need to be running Configuration Professional (not Express) to do this.
View 1 Replies View RelatedI have an problem with my new Cisco 876 Router. I configured port forwarding to access internal network devices from the internet . This works good from external but with my old Fritz box I was able to connect to this internal devices from the same internal network with the dyndns address.
So here is a short review for this:
DYNDNS Address port tcp 80 - > 192.168.0.80 tcp port 80
from ex tern it works but with source address example 192.168.0.20 to destination DYNDNS address tcp 80 (maps to 192.168.0.80 tcp 80 ) it doesn't work. Is there any trick in the config of cisco to let this scenario work?
I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit . Any step by step command.
View 9 Replies View Related