Cisco Switching/Routing :: 3750 Method Of Forcing Non Connected Switch Port LED To Blink
Jan 9, 2012
Any method of forcing a non connected switch port LED to blink for a certain number of times regardless if there is anything connected.The purpose of this is we have remote 3750 switch stacks and quite often have to tell non technical staff to patch to a certain port. It would be much easier if we could say "Connect it to the empty port which just started blinking orange" as the port numbers are difficult for them to see in these locations.A similar feature is available in the ethtool package for linux which makes it really easy for identifying ports on servers. It would be great if a similar feature is available on Cisco switches.
View 2 Replies
ADVERTISEMENT
Aug 1, 2012
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
View 2 Replies
View Related
Feb 7, 2012
I´m facing to one issue with VACL. i have a network lan with 10.40.X.X/16 . in this network i have a Production v LAN 10 with 10.40.10.X/24 and i have created one vlan103 for Guest´ user as 10.40.103.X/24
My goals is to restrict the v LAN 103 to reach or access the v LAN 10, better to restrict Guest user access to the production v LAN. So i try to put this script with VACL method, but does n´t work.
Extended IP access list Restriction-Guest
10 permit ip 10.40.103.0 0.0.0.255 any
vlan access-map Guest 10
action drop match ip address Restriction-Guest
vlan filter Guest vlan-list 10
After that i still able to ping or access to the v LAN 10 form v LAN 103.
View 4 Replies
View Related
May 6, 2013
In my customer having 3750 switch and they have simply assign IP address for vlan and enable telnet in switch and other things are same as default switch.In this switch they have connected 8 cisco layer 2 switches(6 managed and 2 unmanged switch) and approximately 5 servers connected in this switch.In a particular interval,users accessing File server are connected to 3750 switch become hanged for few min.This happen for some particular interval.users accessing this server becomes entirely hanged for few min,then i have configured port monitor cmd and i have installed one wildshark tool to host connected directly to that switch.
View 3 Replies
View Related
Apr 17, 2013
One of the ports on the 3750 stack was configured for VLAN121. It was changed to VLAN40 and the configuration saved. Both VLANs exist in the switch configuration. As soon as a host was connected (in this case, a label printer) the port VLAN reverted back to VLAN121.
View 3 Replies
View Related
Apr 15, 2012
There 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it: [code] Switch is Catalyst 3750 with IOS version 12.2(58)SE1.
View 1 Replies
View Related
Feb 7, 2011
I have a stack with a lot of stack-port changes, but on all the ports, how can I determine the faulty switch in the stack, cables are already verified. We did also a restart of the whole stack power off/on
running version
WS-C3750-48P 12.2(55)SE C3750-IPBASEK9-M
This is the output after 6weeks
Switch#/ Stack Neighbor Cable Link Link Sync # In Port# Port Length OK Active OK Changes Loopback Status To LinkOK -------- ------ -------- -------- ---- ------ ---- --------- -------- 1/1 OK 4 1
[Code].....
View 7 Replies
View Related
Mar 2, 2012
If I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960
View 6 Replies
View Related
Nov 6, 2012
I have a 3750 catlyst switch in my network and it is like a distubation switch,And for the nating and dhcp nomadix is using as gateway in the same network. for one of my local PC i need to config the port forwarding in 3750 switch. How to config the port forwarding on 3750 switch,
View 3 Replies
View Related
Nov 8, 2011
I'm trying to setup a port on a catalyst 3750 so it will pass traffic for 2 vlans. It connects to a (watchguard) firewall which I've configured with a primary IP (for vlan 27) and a secondary IP (for vlan 29).
However I can't seem to find the correct commands to enter on the cisco switch port (I've tried a variety).
FYI the current configuration is...
interface FastEthernet1/0/38
description ## Connection to WG vlan27 and vlan 29 ##
switchport trunk encapsulation dot1q
[Code].....
View 8 Replies
View Related
Oct 7, 2012
We have QoS configured throughout the company, but the standard config we have applied across the 3750 switches only includes the below: We have IP phones (not cisco) attached that are marking with EF, and the PC is an untrusted end device (so needs to be by default marked as zero).Is the above enough to trust VOIP DSCP EF without resetting it to DSCP 0, or do I also need to add a trust line (i.e.: mls qos trust dscp)?
View 2 Replies
View Related
Apr 23, 2012
I would like to know how many port channel can i configured in the switch 3750 X ? and if there is a limitation by IOS ?
View 4 Replies
View Related
Oct 27, 2011
If i fully populate all switch port (Cisco 3750 series) with 100 filter list on each port is it recommendable.
View 4 Replies
View Related
Apr 3, 2012
I have one 12-port 3750 switch having one gig connectivity with ASR-9010 router having IOS-XR. I am not able to ping this link with 9000 mtu size. I have enable system mtu jumbo on switch to 9000 and on ASR router interface mtu is set to 9114. At switch side switch interface is configured as a trunk port and one vlan has been passed on that interface. I am not able to ping the ip 172.16.10.2 with 9000 mtu size.
View 6 Replies
View Related
May 29, 2013
Since Avaya phones do not run CDP, how does the phone know which DHCP pool to pull from to get its IP address if the PC is connected to the phone.
Let's say I have a interface config like this
interface gigabitethernet1/0/1
cisco3750(config-if)#switchport mode trunk
cisco3750(config-if)#switchport access vlan 126
[code]....
And two DHCP scopes configured on the switch. What keeps the phone from pulling from the wrong scope?
View 2 Replies
View Related
May 30, 2013
We have a cisco 3750-48 port switch.We have a few SVI's configured and some static routes configured.I had created a new interface vlan and gave it an IP. I can ping the gateway.
Now I want to add a static route to go out that interface.when I add: ip route 10.x.x.x 255.255.255.0 10.52.10.1
it eccepts it (no errors) But, it does not show in the routing table nor in the config? How to add the static route to go out that vlan interface.
View 15 Replies
View Related
Nov 14, 2012
What the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?
View 3 Replies
View Related
Jul 18, 2012
I have 2 x 3750 stacked, the port number of the master switch is gigabitEthernet2/0/1, slave as gigabigEtherent1/0/1.
Can I change the port numbering so that the master switch gets GigabitEthernet1/0/x?
View 4 Replies
View Related
Feb 26, 2012
I have a switch layer 6500 series connected to a firewall, the port configuration between them is layer 2, in another words I do not configure an IP address in the Cisco switch port to conected it in the firewall, but when a apply a policy on firewall it lose communication with others vlans, just the vlan that is connected between the switch and firewall works, attachment the design. I think that is necessary to configure the connection between the firewall and switch as layer 3 ( a port with IP address in the switch), but I would like to know why? The switch is configured with about 10 vlan and it is a inter vlan routing, a default route is configured in the switch where the gateway is the firewall.
View 5 Replies
View Related
Jan 24, 2013
force something such as a Telnet client to use a particular outbound port when opening the TCP connection?
View 3 Replies
View Related
May 21, 2012
We have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
View 11 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Aug 29, 2012
I currently have a C3750G connected to a C3560G with default auto-negotiation settings. Ports are up and connected a-100 and a-full. I am trying to change the ports speed to 1G, and have tried all possible combinations of "speed 1000" and "duplex full" setting on both ends to no avail. What should port settings be for 1G speed between the two switches?
Here are the current port settings:C3750G:
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
[Code].....
View 8 Replies
View Related
Nov 18, 2012
I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies
View Related
Jan 29, 2012
I have client who has two distant offices with 3750 L3 as core (do all vlan routing for local office) and multiple L2 access switches with multiple VLAN’s connected to it. First 3750 is hub also connected to internet, second 3750 is spoke and acting as a router on stick. We have eigrp configured on both side ISP provided client 100Mbps link as a trunk with two vlan; vlan10 for voice and vlan20 for data. We assigned two small subnets to these vlans 10.15.17.0/29 and 10.15.17.9/29. Hub addresses are 10.15.17.1 and 10.15.17.9 respectively. How to force voice over VLAN10 and data via vlan20, but still do some load balancing? How to setup default route on second (router on stick) switch?
View 1 Replies
View Related
Mar 5, 2013
I have 2 PE routers connected to each other via 2960S and 3750 (non-metro) switches:
[PE1] -- [2960S] -- [3750] -- [2960S] -- [PE2]
I will be sending voice and data traffic between the two and my voice traffic will be marked DSCP EF & EXP 5.
Since the 2960's and 3750's can't match on the EXP bits, I am wondering if the "mls qos trust dscp" command still works. Is the 2960/3750 able to match on DSCP even though there's an MPLS header on top of the IP packet?
I'd like to avoid having to tag my VLAN traffic on the PE and rely on COS to achieve QoS in this case.
View 1 Replies
View Related
Jun 27, 2010
A specific switch port which happens to be part of a 2 switch 3750 Switch Stack is seeing multiple CDP packets from 3 extra switch port interfaces that are not directly connected. Noteworthy is that the far end devices have the correct CDP entries and I physically confirmed at least two of those connections that lead to the switch "upstream to the culprit switch". Tricky part is that its production so room for maneuvering is limited. At some point I disabled all Ports save for the real uplink and the problem momentarily disappeared. Re-enable the interfaces problem resurfaces. Is there an explanation, technique to eliminate the culprit with minimal disruption?
View 4 Replies
View Related
Jun 4, 2012
I am troubleshooting a fiber connectivity issue.Now I have two switches, one is 3750, and another is small biz 300 series switch. Both switch has a single mode smf gbic. Now I have two swtiches face to face and connect with a single mode cable. Do you think if I would get a link light on? Both ports are no shutdown.
View 3 Replies
View Related
May 8, 2012
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
View 3 Replies
View Related
Jun 5, 2013
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
View 2 Replies
View Related
Dec 28, 2008
what is the use of no switch port command in L3 switch?
View 7 Replies
View Related
Feb 26, 2012
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
