In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 RepliesI have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I have 3750 series with GIBICs ports I want to create 10 vlans with its sub-net and enable all vlans to access internet.
View 4 Replies View RelatedMy architecture is the same as show on the link with some difference.I use the router 1841 for inetrnet connexion instead of 7200VXR, this router 1841 is connected on the catalyst 3750 port G1/0/1.I use catalyst 2960 instead of catalyst 2950 or 2948.I use ASA 5510 for conexion on remote branche(I have 5 remote site), This ASA is connected on the catalyst 3750 port G1/0/37
Result of the test:
-I can ping devices in the same Vlans
-I can ping devices in different VLANs
-I can ping all device from the catalyst 3750
I cannot ping the router 1841 or ASA 5510 from the any devices (computer)The gateway of each computer is the correpondant VLAN IP address configured on the catalyst 3750.Why I cannot ping the router 1841 or ASA 5510 from the any devices (computer)
Does Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedI have a DC topology based on 2 layers, access and aggregation, based on 2 pairs of N5548Ps, both without L3 Daugher Cards. My intent is to use the aggregation N5K pair as L3 inter VLAN layer, so I configured all the VLAN default GWs there. The 2 layers are interconnected via vPC, in a double-sided vPC topology for some N2Ks and some vSwitches. The point is that, despite connecitivity is working fairly ok, for some applications, like file transfer via either FTP or HTTP, between hosts in different VLANs, the performance is too poor. The file transfer starts ok, but after a while it becomes lower and lower. ICMP is working, but I can see some strange random behaviour, like having some packets taking more that 20 ms (sometimes 40 or more), whilst average is 2 ms.
I read through some articles saying that until you don´t have the L3 license (the one coming with L3 Daughter Cards) you can expect some weird behaviour on L3 level. Is that true?. What can I do apart of purchasing L3 Daughter Cards?. Can I enable L3 Basic license at the moment (I don´t need dynamic routing for now).
Here some excerpts of what I´m saying:
PING results:
10000 packets transmitted, 10000 packets received, 0.00% packet loss
round-trip min/avg/max = 0.809/2.496/57.559 ms
System version: 5.0(3)N2(1)
License and features on the N5Ks:
switch# sho license usage
Feature Ins Lic Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
FCOE_NPV_PKG No - Unused -
FM_SERVER_PKG No - Unused -
ENTERPRISE_PKG No - Unused -
[code]....
We have two Cisco 5505 firewalls connecting to two ISP's . The two internal LAN's on the firewalls are 192.168.184.0/24 & 192.168.186.0/24. We also have a Cisco C3560x layer3 switch with vlan interfaces 184.3 & 186.3. We have two DGS-3100 Dlink layer 2 switches connecting our users to the Layer 3. Ip routing is enabled for intervlan communication & I can reach the Switch interfaces & firewall gateways from machines on both on the vlans.We have pbr enabled on the 3560 & users only on the .186 network can get to the internet. The switch is running the ipservices license & the sdm template is "desktop routing" .
Users on the .184 cannot access the internet but we can ping the layer3 interface & the firewall gateway. [code]
Can nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies View RelatedI recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
I am working for a large campus network. The network has more than 70 VLANS in a Layer 3 Switch(Catalyst 4503). Customer wants to stop intervlan routing between all vlans except 2 vlans. How will i do that? I have also a Firewall (ASA 5520) & a Router (2811) in up of the switch. Besides this, I have run HSRP in Layer 3 Switches for redundancy.how will i stop intervlan routing between VLANS except 2, with ACL or any other process has?
View 10 Replies View RelatedI'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
Subnet to restrict is 10.100.15.0 (VLAN 15)
STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.
ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
STEP 3: Created VLAN access list
vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
vlan access-map VACL_15 20
match ip address SACL_15
action forward
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:
1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.
you find attached my network architecture with 2 Nexus 7010 on core layer and 2 Nexus 5020 on distribution layer, each one with 1 N2148T fabric extender switch. PC-A1 and PC-A2 are connected to one N2148T, PC-B1 is connected to the other N2148T. Nexus-7000-1 is HSRP Active for all VLANs, Nexus-7000-2 is HSRP standby. PC-A1 and PC-A2 are connected to VLAN A, PC-B1 is connected to VLAN B. PC-A1 and PC-A2 have the same default gateway correspondent to IP HSRP on VLAN A. It happens that PC-A1 is able to ping PC-B1 while PC-A2 is unable to ping PC-B1. If I issue a traceroute from PC-A2 I see Nexus-7000-2’s physical IP address as the first hop even if Nexus-7000-2 is HSRP standby. After the first hop the traceroute is lost. If I shutdown Port-channel 20 on Nexus-5000-2, PC-A2 starts to ping PC-B1.I can’t understand what’s wrong in this architecture.
View 6 Replies View RelatedI have just bought myself a Cisco 2821 ISR.At present in my home I have a Cisco 2621XM. Fast Ethernet 0/0 is connected to a 3524XL as a trunk to provide my LAN with inter-vlan routing. it works great. Fast Ethernet 0/1 is connected to my ISP's cable modem and uses the command "Ip address dhcp" to get an IP and all other info from my ISP.FA 0/1 is Ip nat outside and the FA 0/0 and all sub interface like 0/0.1 .24 .168 etc all ip nat inside.I get intervlan routing and access to the internet via this router.I have this 2821 to replace the 2621XM as I plan to run CME on it and want gigabit routing on my vlans as at the moment on the 2621 routing between vlans it at half duplex or seems to be.I have configured the 2821 to ip nat outside on gig 0/0 and ip nat inside on gig 0/1 and all of the sub interfaces (same setup as my 2621 but with gig ethernet)I have no access to the internet at all but I can ping www.google.co.uk and other domain names from the terminal session when I am connected to the 2821 via the console or telnet/SSH. the gig 0/0 has an IP assigned from my ISP too but no other nodes on the network can ping outside.Am I missing something here? the version of IOS is V 15.
My access list goes someting like
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 100 permit ip 10.0.0.0 0.255.255.255 any
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
and so on
I still cannot access the internet.....
I have a SG 300-28 switch with the latest firmware installed running in Layer 3 mode.
I configured this router with 4 VLAN's where VLAN 1 is connected to the network router. All VLAN's call all communitcate with one another. How do I go about configuring VLAN's so that they can only communicate with the router and the internet and not each other?
I have one cisco 3750G-48 switch, one cisco 3560G-PS switch, Cisco UC520, cisco 2851 and cisco wireless access point.i have setup up intervlan routing between the two cisco switches and the uc520 with a total of four VLANS, the problem i'm having is with the 2851 router, I have created a trunk between the 3750 switch and the 2851 router. should I create subinterfaces on the 2851 router for the four vlans by doing gigabieethernet 0/0.1, 0/0.100 and so on or should I create BVI subinterfaces.
reason I ask is I created four vlans on the vtp server switch which is the 3750 and I connected the uc520 to the 3750 switch via a trunk interface and set up vtp client on the uc520, after I setup p the vtp on the uc520 the vlans were automatically created on the uc520 with each vlan having its own BVI interface.
So I am not sure how to configure the 2851 router to interact with the four vlans. also the 2851 router have two hwic 1adsl wics installed which will have two adsl connections coming in.how to set up the 2851.
I am looking for a reasonable switch but it has do do inter-VLAN Routing. I know I could go with a 3560/3750 with IP Services but I am also thinking the 2960S with IP Base IOS might do?
I have looked up the IP Base IOS and it does list IP Routing but how to actually configure inter-VLAN Routing on a 2960S with IP Base?
I have a 2911 router connected to a 3750 switch. I have configured vlan interfaces on the 2911 router:I am using the vlan 89 (89.2) as the management ip address for me to remotely get to the switch. Is this a proper configuration or could this cause issues in the future.
View 4 Replies View RelatedProbably an easy fix but something's weird in my config. I am setting up a new network, so this is not production, Routed environment, down to the access layer using 3560-x l3 switches.
vlan 10: data
vlan 20: wifi
vlan 30: wifi guests
vlan 40: voip
My objective is to allow all traffic OUTBOUND to certain subnets (10.10.0.0/24, 10.10.100.0/24, 10.10.110.0/24 10.10.120.0/24) and block any other 10.0.0.0/8 networks. By doing it this way, after blocking all other internal traffic, I allow everything else to ensure internet traffic can go out.
Extended IP access list VLAN10_TRAFFIC_FLOW 10 permit ip any 10.10.0.0 0.0.0.255 20 permit ip any 10.10.100.0 0.0.0.255 30 permit ip any 10.10.110.0 0.0.0.255 40 permit ip any 10.10.120.0 0.0.0.255 50 deny ip any 10.0.0.0 0.255.255.255 (5 matches) 60 deny ip any 172.16.0.0 0.0.255.255 70 permit ip any any!interface Vlan10description DATAip address 10.104.10.1 255.255.255.0ip access-group VLAN10_TRAFFIC_FLOW outendThe problem is, from the above info, when I ping 10.10.0.5 from a workstation in VLAN 10, it should match rule 10, but instead if matches rule 50 (as shown by the 5 matches)
I just got my Cisco SG300 28, but I have some problems getting the routing to work. I get the vlans to get to the router, with the default route. But not getting them to talk with each other. I can ping the IPs from the cisco, but I am not getting traffic to go from vlan 1 to vlan 2. When I try to google, it say that it should do it automatically, and I found no setting for it. It looks like it not creating any route for the interfaces.
View 2 Replies View RelatedI'm having an issue routing between vlans. I have vlan 1, and 2. I want to ping something on vlan 2, from vlan 1. I cannot ping from a computer on vlan 1 to a computer on vlan 2. I can ping each computer from the ASA 5505. I get an error on the ASA when I try to ping from the computers. The error is Failed to locate egress interface for UDP from voice:192.168.0.199/137 to 192.168.1.200/137. I can't understand why it even mentions IP 192.168. 1.200/ 137... I reset the unit configuring it from scratch and still no go. I have no given a static route to the out yet.. I need to get inter-vlan routing working first. [code]
View 13 Replies View RelatedI have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies View RelatedI have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies View RelatedI have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
I have a Cisco 3750 with private VLANS configured.. VLAN 2 is the "primary", VLAN 3 is "isolated" and VLAN 4 is "community". This is all working correctly, however I now have the need to another VLAN called "production". I need the production VLAN to be able to reach all the private VLAN hosts (community and Isolated), and vice versa
View 2 Replies View RelatedI have a quick query which i need ratified before proceeding. I have the following scenario -
Two Cisco 3750v2 switches with stackwiseISP allocated block of /26 (64 addresses)8 customers each with a VLAN and SVIInternet facing VLAN and SVIDefault route to ISP router Lets say the ISP has given me the network range 10.10.10.0/26 (we'll assume this is routable on the internet for the purposes of this example) and a default gateway to the internet of 10.10.10.1 within this range. I have configured a public facing VLAN as follows -
VLAN 300
name PUBLIC
int VLAN 300
IP Address 10.10.10.2 255.255.255.252
I have then created a default route as follows -
ip route 0.0.0.0 0.0.0.0 10.10.10.1
With this configured, the switch can successfully route upstream to the internet with no problems. I have then moved onto the customers and depending on what service they have purchased, I have subnetted the 10.10.10.0/26 range into smaller subnets. See as follows -
Customer A - 10.10.10.4/30
Gateway IP - 10.10.10.5
Useable IPs - 10.10.10.6
Customer B - 10.10.10.8/29
Gateway IP - 10.10.10.9
Useable IPs - 10.10.10.10 - 10.10.10.14
This continues for each customer depending on how many IP's the have purchased. I have then assigned these IP ranges to a customer VLAN and SVI as follows -
Customer A
VLAN 10
name CUST-A-VLAN
int VLAN 10
ip address 10.10.10.5 255.255.255.252
[code].....
It is then up to the customer as to what equipment they use and how they NAT or firewall their internal networks.
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
Just messing around with packet tracer for a little practice. I tried to setup a router on a stick config with 3 switches trunked and PCs on different vlans. Anybody know of any issues that may arise with STP and inter-vlan routing? I set everything up correctly with trunking, addressing, encapsulations, vlans, but did not touch STP. Unable to ping from any PC to any where.
View 19 Replies View RelatedI know very little about switches. This is the first time I've ever touched them. However, I'm the only one in the company who has the slightest knowledge on how to make them work.
4 vlans
vlan 1 - 192.168.32.1 - Existing network with Internet access
vlan 33 - 192.168.33.1
vlan 34 - 192.168.34.1
vlan 35 - 192.168.35.1
From the laptop on vlan 33 I can ping the management interfaces (192.168.x.1) for each of the vlans. However, I cannot ping anything on those networks.
Below is what I have with the config. Right now not much attached to these switches until they are setup.
Code:
config-file-header
poe-switch
[Code].....
Say I have a managed switch that supports VLANs. I have two computers and one server connected to the switch (I'll call them PC-1, PC-2, and SRV-1).Without routing, I want both PC-1 and PC-2 to talk to SRV-1 and vice versa, however I don't want PC-1 or PC-2 to talk to each other.I achieve this by making each port a trunk port. I make PC-1 a member of VLAN 2, PC-2 a member of VLAN 3, and SRV-1 a member of VLAN 4. The port that SRV-1 is on I make a tagged member of PC-1 and PC-2 (VLAN 2 and 3 respectively) and make the ports the PCs are on a member of the SRV-1 VLAN (VLAN 4).Everything tests OK (that is, the clients can't talk to each other, however the clients can individually talk to the server)
View 6 Replies View RelatedWhat is inter vlan routing protocol? What are its three modes?
View 6 Replies View Relatedi am doing a set-up having the ASA as my Layer 3 device providing inter-vlan communication. ASA with 8.3 firmware. how i can achieve this goal. i am trying to follow some answered topic related to this but its pre 8.3. VLANs created on the same physical have same security level.
View 2 Replies View Related[code] I would like to config two IP ranges, one for staff, one for guest wireless access. The dlink wap supports multi vlan SSIDs.Reason I'm doing this is to prevent access on the guest wireless to access the win 2003 server.Will the switch inter vlan route the 192.168.2.1 to 192.168.1.1? How will vlan 2 get DHCP, will dhcp relay need to be set on vlan 2 to 192.168.1.20 ? [code]
View 2 Replies View RelatedCan inter VLAN routing be done on SRW (Cisco 300 series) switches ?
View 5 Replies View Related