Cisco Switching/Routing :: VSS Switch Got Hang After Inserting 6708 Module?

Jan 11, 2012

We having a VSS switch (9 slot chasis) with ios "s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI4", slot 7-9 are currently free. We wanted to install WS-X6708-10G-3C module on slot 7. Once we installed the module it didnt come, after waiting for 15-20min again we removed and inserted, but module didnt come up and we could see following logs on the console:
Jan 12 08:57:40.146: %ISSU-SW2_CFC2-3-ERP_AGENT_SEND_MSG: client/entity send failed; error code is timeout
*Jan 12 08:57:40.330: %ISSU-SW2_SPSTBY-3-ERP_AGENT_SEND_MSG: client/entity send failed; error code is timeout
Jan 12 08:57:40.146: %ISSU_ERROR-SW2_CFC2-3-START_NEGO_FAILED: ISSU NTI Client(2040): failed to start negotiation (ISSU_RC_CLIENT_ENTITY_DOES_NOT_EXIST_IN_PEER)


Afer some time VSS switch didnt response to console commands and all the users in access switches were not able to reach the gateway (VSS). Then the problem disappeared once we rebooted both the switches in VSS.why the VSS switch become non-responsive?

View 1 Replies


Cisco Switching/Routing :: Hang During Boot Of WS-C4948-S Switch

Apr 3, 2013

I encountered an issue while trying to boot Catalys WS-C4948-S switch. I power on the switch and I'm able to see the boot messages thourgh serial console cable. But it gets stuck at line "Image text-base: 0x1000000, data-base: ..... ". Also I can enter into rommon mode. I tried to use different kinds of IOS images, tried to boot from tftp but with no luck, the issue is the same.
There are no erros on the screen, it just gets stuck when it enters into IOS, so I don't see the IOS prompt.

View 5 Replies View Related

Cisco WAN :: Configuring Xconnect On 6708 Module

Dec 29, 2010

i have 2 X 6509 with 6708 & sip-400 with spa 1XOC-48.i need to have a layer 2 tunnel between them.can i have a vpls configuration with that scenario ?, meaning configuring the Xconnect on the 6708 module and the sipspa will do the vpls encapsulation ?

View 1 Replies View Related

Cisco Switching/Routing :: 3750 Switch Connected Computers Hang For Few Minutes

May 6, 2013

In my customer having 3750 switch and they have simply assign IP address for vlan and enable telnet in switch and other things are same as default switch.In this switch they have connected 8 cisco layer 2 switches(6 managed and 2 unmanged switch) and approximately 5 servers connected in this switch.In a particular interval,users accessing File server are connected to 3750 switch become hanged for few min.This happen for some particular interval.users accessing this server becomes entirely hanged for few min,then i have configured port monitor cmd and i have installed one wildshark tool to host connected directly to that switch.

View 3 Replies View Related

Cisco Switching/Routing :: 2960 / Inserting Device Into DMZ?

Jan 9, 2013

I have a /28 subnet between my internal and external firewalls for L3 connectivity. On our internal firewall, I have a default route for internet traffic pointing to the external firewall (
We will be inserting a web filter appliance as indicated on the diagram. The appliance requires an IP address to be assigned to the LAN interface.
What is the best way to accomplish this with minimal impact? Will my default route on my internal firewall have to change to the IP of the web appliance if I address the web appliance on the 10.10.1.x subnet?Should I address the web appliance on the 10.10.1.x subnet to begin with, or create a vlan on the 2960 and a L2 interface on one of the firewalls?

View 1 Replies View Related

Cisco Switching/Routing :: Inserting 2 ZHWIC 4ESW In 2911/K9

Jul 8, 2012

We have cisco 2911/k9  we fixed 2  HWIC-4ESW crds in 2911. I create 4 vlan i have assigned 1 HWIC-4ESW  all vlans are working fine
when i configure 5 th vlan it assigned second  HWIC-4ESW 1 port but interface status showing up. i connected one system to that port i try
to ping that port that port notable to pinging is there any  activation for that second HWIC-4ESW.

View 11 Replies View Related

Cisco Switching/Routing :: To Reload The Module 3 On The 6509 Switch

Jul 31, 2012

Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?

View 1 Replies View Related

Cisco Switching/Routing :: Switch Module Install For 2951?

Sep 3, 2012

Any doc for installing the a PoE switch module for a 2951? I find alot about the 2951 PoE Power supply but nothing for the switch module.

View 5 Replies View Related

Cisco Switching/Routing :: Module Power Down On 6513 Switch?

Apr 28, 2012

We have Communication Media Module (WS-SVC-CMM) mounted on 6513 switch. It went down twice and we brought it up by applying "power enable module".

View 4 Replies View Related

Cisco Switching/Routing :: Setting Up Switch Module On 2951?

Sep 18, 2012

I'm trying to set up a 2951 with a 24 port switch module. I want the ports to act similiarly to the ports on an 881 router - where I assign the VLANs on the router and I set the VLANs to the switchport interfaces.I would like to be able to create the VLANs on the router portion of the 2951 and then, enter the switch module and configure the Ports to the VLANs but, how do I logically connect router to the switch? Is it an internal logical interface - meaning how are the VLANs getting from the router to the switch?

View 24 Replies View Related

Cisco Switching/Routing :: GLC T Sfp Module Showing Unspecified In Switch 2960

Mar 6, 2012

We have supplied Cisco Swtch 2960 with gig SFP modules. It is working fine. However, when I do a show inventory it show proper part no. for the switch chassis but for the GLC T module it shows as unspecified in the PID column.

View 1 Replies View Related

Cisco Switching/Routing :: Module Ws-x4548-rj45v+ And 4506 Switch

Oct 4, 2012

I have a problem with a newly bought ws-x4548-rj45v+ i've plugged in the module but when i do show modules all , it show as unsupport
Power consumed by backplane : 0 Watts
Mod Ports Card Type                              Model              Serial No.---+-----+--------------------------------------+------------------+-----------1     2  Supervisor IV 1000BaseX (GBIC)         WS-X4515           JAE1048GAXQ2    48  10/100/1000BaseT (RJ45)                WS-X4448-GB-RJ45   JAB064806WN3    48  10/100/1000BaseT (RJ45)                WS-X4448-GB-RJ45   JAB063005DB4     0  Unsupported module                     WS-X4548-RJ45V+    JAE1545056U
M MAC addresses                    Hw  Fw           Sw               Status--+--------------------------------+---+------------+----------------+---------1 0007.0e64.f880 to 0007.0e64.f881 5.2 12.2(20r)EW1 12.2(46)SG       Ok2 000b.5fa4.da20 to 000b.5fa4.da4f 1.0                               Ok3 0009.e844.d760 to 0009.e844.d78f 1.0                               Ok4 ccef.4815.9bf0 to ccef.4815.9c1f 2.0                               Unsupport

View 2 Replies View Related

Cisco Switching/Routing :: 4 And 8 Port Switch Module In 1941 Router

May 23, 2013

My questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?

View 1 Replies View Related

Cisco Switching/Routing :: 2811 With 16 Port Switch Module Configuration?

May 12, 2013

I have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.

View 9 Replies View Related

Cisco Switching/Routing :: Adding N7KM132XP-12 Module To Nexus 7K Switch

Jul 31, 2012

Trying to find some documentation as to whether there are any other steps for inserting this new module in our N7K. We have 2 blades in already and 2 Sups in 5 & 6. I'm assuming its like the 6500s, where we just slide it in and the OS configures the global parms for it and the default VLAN.

View 2 Replies View Related

Cisco Switching/Routing :: Switch To C6500E Backbone Without Getting Network Module

Apr 16, 2013

can i use any downlink port of the C4500-X switch as uplink without the need of the network module?i need to connect that switch to C6500E backbone without getting the network module, is that OK or i must get the network module?

View 1 Replies View Related

Cisco Switching/Routing :: How Switch Module Works In 2911 Router

Sep 4, 2012

how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.

any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.

View 1 Replies View Related

Cisco Switching/Routing :: 2960 Switch Hanging With SFP Module Slots

Sep 2, 2012

My Cisco 2960 Switch hanging problem (does not work or LED light), when i removed SFP  module slots its working fine.

View 1 Replies View Related

Cisco Switching/Routing :: 3925ISR Backing Up IOS And Configurations From Ether-switch Module

Jul 10, 2012

I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.

View 1 Replies View Related

Cisco Switching/Routing :: 6513 Switch Giving Module 11 In Power Down State

Apr 7, 2012

After a power problem at our data centre we find Module 11 of our Cisco 6513 Core Switch in PWR Down state.Show Module 11 returns: Status: PWRDownShow Power Status Module 11 returns: OperStatus Off (Module Reset due to an exception or user request).The command:
Power enable Module 11 was issued and returned the following:  %PM_SCP-SP-1-LCP_FW_ERR: System resetting module 11 to recover from error: Linecard received system exception. Errcode = 2509000001.%OIR-SP-3-PWRCYCLE: Card in module 11 is being powercycled Öff (Module reset due to exception or user request%C6KPWR-SP-4-DISABLED: Power to module in slot 11 set off (Module Reset due to exception or user request),We have restarted the switch twice. The module is currently not passing traffic causing downtime to services.

View 6 Replies View Related

Cisco Switching/Routing :: Can Put Module On 4507R Switch Running On Live Production

May 2, 2012

Can we put a module on a 4507R switch running on a live production? The module will come from a 4506 switch.

View 8 Replies View Related

Cisco Switching/Routing :: Configuration Module Supervisor Switch Catalyst 4500

Jun 4, 2012

switch catalyst 4500 with ios cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin. I need to configure modules 3 and 4 of supervision, the problem is that I need the 4-port module 3 are active but only the first turn on both the module 3 and the first port on the module 4. [code]

View 1 Replies View Related

Cisco Switching/Routing :: 3925 With 48 Port Switch Module Infinite Loop

Jan 19, 2012

I have a 3925 Router with a 48 port switch module (part number SM-D-ES3G-48-P).  I have no problem accessing the 3925 Router, but when I go into the 48 port, I get an error that reads
Error Hardware not supported by firmware. Try loading a newer software instead. System Resetting...
I know that the wrong IOS is installed on the switch, but the problem is that this is an endless loop.  The switch resets then comes back to the same error.  How to get the switch out of this loop so that I can load the correct IOS. 

View 1 Replies View Related

Cisco Switching/Routing :: Replacing A Dual Supervisor Module In A 6513 Switch?

Jun 18, 2012

I have a supervisor blade, (VS-S720-10G-3C), in a 6513 that is faulty and needs replaced. Do I need to replace the IOS on the new supervisor blade to make sure it is the same as the IOS image that is on the Active supervisor module, or will it synchronize automatically?
In the synchronization process, the active supervisor engine checks  the  standby supervisor engine run-time image to make sure that it  matches  its own run-time image. The active supervisor engine checks  three  conditions:
•If it needs to copy its boot image to the standby supervisor engine
•If the standby supervisor engine bootstring needs to be changed
•If the standby supervisor engine needs to be reset
 I was reading the above documentation that mentioned the active supervisor should copy the image if it detects a newly installed standby supervisor blade with a different image, is this correct or was it referring to synchronizing the configuration file?

View 3 Replies View Related

Cisco Switching/Routing :: 1941 Port-Security With Router Switch Module

Feb 29, 2012

I have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE).  I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings.  Is port-security no available on the switch modules?

View 3 Replies View Related

Cisco Switching/Routing :: Layer 3 Module Required For 5500 Series Switch?

May 16, 2013

We are working with a contractor to upgrade our network, and I heard from them that the 5596/5548 might not need the Layer 3 module for our inter-VLAN routhing.  They have yet to give me an answer.
We do have a few static routes on our current layer-3, core switch too. 

View 3 Replies View Related

Cisco Switching/Routing :: WS C3560E 12SD - Connect Server To Switch Through FC Cable With SPF Module

May 6, 2012

Recently I have faced following problem in my office, We have purchased two new Dell Server Power Edge R910 with built-in 10GB FC Network card. Service tag of this two servers are given bellow.
1. 7D94C2S
2. 6D94C2S
You can can Check specification of this two server from dell website{ URL}
We have two CISCO switch and model is given bellow:
Brand: CISCO
Model: WS-C3560E-12SD

We want to connect server to switch through FC cable and both switch have SPF module. But when we connect server to switch, link do not establish even switch and server port light become off.
Then we have tested the following things:
1. Connect server to server through FC cable, it is okay.
2. Connect switch to switch through same FC cable, it is okay.
I don't understand why it is not working.

View 5 Replies View Related

Cisco Switching/Routing :: USB Console Cable For 3012 Blade Center Switch Module

Jul 27, 2011

I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work.  I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is  DB9-to-USB but with no part number.

View 3 Replies View Related

Cisco Switching/Routing :: X4648-rj45V+E Module Not Forwarding Frames / Packets In 4507E Switch?

Mar 26, 2012

I have a problem with x4648-rj45V+E module, which is not forwarding frames/packets in my 4507E switch. I have done the diagnostic and the module test is passed. When i try to ping from one PC to another in the flat network, icmp is not forwarding. Even i cannot see the mac addresses in the mac address-table. But i can ping to my management port in the sup module?

View 12 Replies View Related

Cisco Switching/Routing :: Connect WS-C2960S-48TD-L Switch To WS-X6708-10G-3CXL Module In WS-C6503-E?

Jun 1, 2012

I want to connect WS-C2960S-48TD-L switch to WS-X6708-10G-3CXL module in Cisco WS-C6503-E switch. WS-X6708-10G-3CXL is C6K 8 port 10 Gigabit Ethernet module with DFC3CXL which requires X2 module. on the otherhand, WS-C2960S-48TD-L requires SFP+. Now is it possible to interconnect these two switch interfaces if I use LIU in between. or does WS-X6708-10G-3CXL module supports CVR-X2-SFP+ to use SFP+ transceivers.

View 2 Replies View Related

Cisco Switching/Routing :: 3560 Switches Hang Off With Sub Interface

Jul 22, 2012

Was building a small network in Cisco Packet Tracer and ran in to an issue.  I have 4 routers running OSPF, and off one of the routers I have 5 3560 Multilayer switches.  The router that the switches hang off of, I have a sub-interface with dot1q encapsulation, set for vlan 10 and an IP Address.  The switches have interface vlan 10 configures, and have IPs in the same subnet.  From that router, I can ping/telnet to all the switches without issue.  My problem arises when I try and reach those switches from any other router.  OSPF is set to redistribute static and connected subnets.The routing table is populated correctly on all the routers.  When I ping and trace the packet, it looks like it makes it all the way to the respective switch, but the packet never makes it back.  I've played with the default route on the switches to no avail.  Am I trying to implement this incorrectly, or am I just missing something?

View 4 Replies View Related

Cisco Switching/Routing :: Connect SF200-48 Switch Via Mini-GBIC MGBLX1 Fiber Module To 3750?

Jun 25, 2012

I am trying to connect a SF200-48 switch via Mini-GBIC MGBLX1 fibre module to a Cisco 3750 switch with a GLC-SX-MM fibre module installed both running a 1000 Mbps.  When connected together they do not enable.  Are there compatibility restrictions or is it that the Mini-GBIC modules cannot be used to uplink to a LAN?

View 2 Replies View Related

Cisco Switching/Routing :: Configuring 1941 With 8 Port EHWic Switch Module And Onboard GE Ports In Single LAN?

Jul 1, 2012

Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?

I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?

View 2 Replies View Related

Copyrights 2005-15, All rights reserved