Dell :: Internal Sim Card Insertion Port Xps L520X
Aug 26, 2012i am not able to connect internet using the sim card port of my dell xps15 model no.-L520X. Can you tell me how to connect through the port.
View 1 Replies
ADVERTISEMENT
Cisco WAN :: Card Insertion On 3845 Routers
Oct 6, 2011I need to install a HWIC-2Fe card onto the Cisco 3845 motherboard. Do I need to power down the router for this installation?Also I had a few more queries in regards to 3845 routers.
1) DO C3845 routers support insertion and removal of Network modules while powered on?
2) Do C3845 routers support insertion and removal of Power supply (redundant one)?
3) Is it the case that all Network modules which need to be inserted onto the motherboard require the router to be powered down?
4) If there is a need to replace the Network module from a particular slot with a new one (same make), powering down the router is not required?
Cisco Switching/Routing :: WS-X6708-10G-3CXL Card Insertion Killed VSS And Fan Tray
Jan 7, 2012I currently have a VSS setup on 2 6509-E using 2x VS-S720-10G.Today I tried to install 2x X6708-10G-3CXL, one into each chassis. The first log message I got was that fan tray was going into high-speed mode, is this correct?I then installed the second card in the 2nd chassis and it killed my VSS and proceed to reload the switches. it now also appears to have killed one of my WS-X6724-SFP cards, as it no-longer boots and I get the following errors:
000249: Jan 8 12:52:34.201 GMT: %DIAG-SW1_SP-3-MAJOR: Switch 1 Module 1: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results.000250: Jan 8 12:52:34.205 GMT: %CONST_DIAG-SW1_SP-3-BOOTUP_TEST_FAIL: Switch 1 Module 1: TestLoopback
Also I can't read any of the log files in 'bootflash diaginfo' as it says the file doesn't exist.Everytime I know re-insert the WS-X6724-SFP cards it kills the VSS
Dell :: Cannot Find Single Driver For E6400 Internal Wi-Fi Card That Works With Windows 7 64-bit
Jan 25, 2012I just recently purchased a dell latitude E6400 laptop and I did a clean install of Windows 7 Ultimate 64-bit on it, not an upgrade. I also installed service pack 1 right after the OS install. My problem is I cannot find a single driver that allows my WiFi card/connection to show up in Windows. I have been browsing the internet like a fiend and cannot find a single driver or solution anywhere for this. Every install or driver I try either shows an error saying "incompatable" or just does not fix the issue. All I want is my WiFi card to work, and dell did not have any drivers that worked off of its support site even when I put in my service tag number. compatable driver for the WiFi card for windows 7 64bit? Or steer me in the right direction to get the WiFi working on my laptop?
View 4 Replies View RelatedDell :: Drivers For Wireless 5300 PCI Express Internal Half-Height Mini-Card?
Mar 1, 2012I have the Wireless 5300 PCI Express Internal Half-Height Mini-Card ordered and now need to find the drivers. My system is a 1735 Studio laptop running 64bit Windows 7. The Dell sales rep said the card came only with the card and a flat head screw.
View 3 Replies View RelatedDell 1390 WLAN Mini-Card / Can't Connect To DHCP And Port Forwarding Not Working
Dec 22, 2011The first is I have a laptop running XP with a Dell Wireless 1390 WLAN Mini-Card built in to it. But for some reason when I'm using that wireless connector my computer won't connect to my router and give me a 192.168.0.x address, it gives me a regular IP address. I can surf the net and everything but I can't access files on other computers. But from it it'll allow me to connect to the router admin fine.Whenever I put the mac address in to my DHCP setting on my router it comes up * RESERVED INACTIVE * and never gives my laptop a local ip address.The other problem is on my 192.168.0.2 computer I've tried to set up port forwarding but it won't open the ports. My router is a Motorola SBG6580 provided by my cable company. This particular computer is connected by Ethernet and not Wifi if that makes a difference.
View 2 Replies View RelatedTP-Link ADSL2+ Wireless :: TD-8970 Port Forwarding To A Different Internal Port
Mar 7, 2013Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
Cisco Routers :: RV042G Port Forwarding From Public Port To Internal IP?
Oct 11, 2012Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
Dell :: Connection/Network Manager Not Listing Internal Modem (Dell XPS L502X)
Nov 1, 2012I recently install Windows8 Enterprise build 9200 on my Dell XPS L502X and everything is working fine so far except my modem. In device manager its installed properly but the network manager doesn't list it as an option to connect to (as it usually would in win7),
View 2 Replies View RelatedUpgrading Internal Wifi Laptop Card
Mar 5, 2013I am trying to upgrade some older laptops (about 4 years old or more) WiFi. Most of them have I believe 802.11 b,g cards in them. I would like to upgrade to b,g and n so they will connect to all home networks more easily. I believe most of the b,g and n internal WiFi cards have three wires were all my laptops only have two.
View 5 Replies View RelatedLinksys Wired Router :: RV042G / Create Service To Forward Public Port 9010 To Internal IP Address With Port 23?
Oct 12, 2012Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies View RelatedDell Wireless 1390 WLAN Mini-Card - Wireless Network Card Error
Apr 20, 2012I think I am having problem with my network card I am running windows 7 with Dell wireless 1390 WLAN Mini-Card lots of times the signal is low and I get the error message no internet connectivity or some other error message that I am not being able to connect to the network provided by my wimax modem, Is there any program that I can download to test if there are any errors related to the network card or any way to fix this?
View 3 Replies View RelatedDell :: Vostro 1500 And Cannot Connect To Wireless Network With Dell 1395 WLAN Mini-card
Jan 13, 2012I have a Vostro 1500 and cannot connect to a wireless network with a dell 1395 WLAN minicard os XP home, what are possible solutions?
View 1 Replies View RelatedCisco WAN :: Online Insertion And Removal On 3845 And 2821?
May 3, 2011I've got a 3845 and a 2821 and I need to add another WAN interface card on each router and wonder if this can be done live while the router is running.
View 2 Replies View RelatedCisco Switching/Routing :: Configure 6500 Line Cards Before Insertion?
Dec 7, 2011Is it possible to configure the switchports on a 6500 linecard before it has been inserted?
So for example, I have a 6509 with slot 9 free. I'm going to install a 48 port line card. Is it possible to configure those 48 ports before the card is inserted?
Cisco Switching/Routing :: Catalyst 6513 - Redundant Supervisor Not Synced After Insertion
Aug 23, 2012The SuperVisor engine in slot 1 of a Catalyst 6513 needed to be replaced because a hardware defect. The SuperVisor engine in slot 2 is active and running CatOS 8.5. The new SuperVisor engine for slot 1 came with CatOS 6.3 and was not syncronized auromatically after insertion. When the customer enter the command "Show boot" he get the output:
AG-A6513-51> (enable) sh boot
BOOT variable = bootflash:cat6000-sup2k8.8-5-5.bin,1;bootflash:cat6000-sup2k8.7-6-2.bin,1;
[Code].....
D-Link DIR-655 :: Internal Port Blocking / Routing?
Jul 14, 2012Have a Rev. B1 w/207NA on Time Warner with a Moto Surfboard SB5150.Working with TiVo's, we've been through hell and back trying to resolve why Multi Room Viewing doesn't seem to want to work - but only one way! The newest TiVo's their Premiere model with HD and all the bells and whistles, it sees the other TiVo and all the other software that can send programs back and forth with it.
I brought on a Series 2, which is an older model that's non HD and has some older software in it. While the Premiere and the other PC's/Software around the building's network can 'see' the Series 2 and it can 'see' the other shared PC's, etc. the thing can't 'see' the Premiere.This has been going on for awhile, I've worked with TiVo Support also to unlock ports, IP addresses and anything else we could think of. Still no luck. Then we had a strange occurance!
The DIR-655 seemed to 'lock up' or disconnect from the Net. One day I was surfing the Now Playing menu in the Series 2 and the other TiVo wasn't showing as usual. I checked it again during a commercial for something totally different and suddenly noticed there it was!! I thought it was weird, so I went out front to check with the person using the main TiVo if they had made any changes or done anything - they hadn't, but did mention their Net connection was gone.
I turned around and looked at the 655's status lights and noticed while all the rest were fine - the WAN/Net status light was totally out. Not a single blink. And then I looked at the Moto cable modem and noticed it's 'activity' light was also totally dormant. I twisted the Moto to get a better look at it and things started working again, I tightened the cable modem cable on the rear and that was it.
From that point on - once again, the front TiVo won't show on the back TiVo! Does every other way, but not that. In our discussions on TiVo we thought it could've been the cable modem firewall or something, but I retested it and this time it had NO effect. Tried not only taking out the cable-cable but the Ethernet cable as well to ensure all were tested. Still didn't now up. What I thought was going on was the 655 had turned into a giant 'Hub', which would've caused the TiVo's to use their old-fashioned Beacon software to 'find' each other. When the 655 software kicked back in from that glitch, the hub setup would've obviously stopped and the 655's software settings would've kicked back in.
I have a complete list of the ports internally that need to be open for those two TiVo's to communicate, but I can't find anything in the 2.07NA GUI (or Help manuals) that tell me how to write a rule to open those ports internally. I wouldn't think there's any internal blocking or firewalling going on (I have it set to allow communications between clients on the internal Net) but there's so many settings in this GUI it makes your head spin!
Cisco :: Forward A Port On An ASA 5505 To An Internal Ip Address?
Apr 24, 2012I have been asked to "forward a port on an ASA 5505 to an internal ip address." Sounds easy for most of you, and I thought I did it right, but I am not certain. Basically, they want it set up so that when xx.xx.xx.xx:30000 (x's = the firewall ip with port 30000) is accessed from outside, it is forwarded to an internal ip on port 30000 (xxx.xxx.x.xxx:30000)
Here is what I tried from within ASDM 6.4:
1. NAT Rules-add static NAT route:
original-Interface: inside
-Source: xx.xx.xx.xx (local ip of computer on LAN they wish to access from outside)
Translated - Interface - Use Interface IP Address
Enable PAT: Original and Translated port both set to 30000
2. Access Rule - add
Interface: Inside
Source: any
Destination: xx.xx.xx.xx (IP of Firewall)
Service: tcp/30000
Cisco Firewall :: Isolate Internal Net On Port 4 Asa 5505?
Nov 20, 2011I want to have my port 4 on the asa 5505 only allow access to the internet and not the internal network, what do i need to do?
View 1 Replies View RelatedCisco WAN :: Get Mail Server On Port 443 From Internal Network
May 24, 2012I write here to see if some kind soul can not solve my problem (which is common to seeso many people around the world). problem: I have a mail server (192.168.1.17) configured static NAT because it is accessible byPublic IP (PPP.PPP.PPP.PPP). Everything works properly from the outside, but if I get my Mail server (on port 443) from the internal network (192.168.1.xxx) there 'verse. This configuration is called Nat inside-to-inside is done by default by some SOHO routers(such as the TPLINK from 25 euros) but Cisco did not succeed. I search on the internet for 2 days without a get nowhere. PS: I have a Cisco 1801 router. (or 1941 as another router).
View 13 Replies View RelatedCisco WAN :: 877w Port Forward 80 And 443 To Internal Server
Feb 21, 2012I'm new to the Cisco world and have so far got internet and VPN working (without SDM) using the IOS commands.I have hit a stubling block with port forwarding ports 80 (http) and 443 (https) to my small business server for outlook web access.I need to forward port 80 and 442 to internal LAN server 192.168.10.1.The Cisco 877 has a local IP address of 192.168.10.254. [code]
View 6 Replies View RelatedThomson TG585 V8 - Port Forwarding Internal 53 To Opendns 5353
Jan 10, 2012My isp seems to be using a Transparent DNS proxy and I tested DeleGate on a windows PC and opendns works but I would like to set my router to forward all 53 udp to 5353 udp on to 208.67.222.220 so that opendns can work on ipod,ipad and smartphone etc, I have tried to use the following command to set the router to forward from port 53 to 5353 but no luck:
nat mapadd intf=Internet outside_addr=208.67.222.220 inside_addr=192.168.1.66 protocol=udp outside_port=5353-5353 inside_port=53-53 mode=auto weight=10
Cisco Routers :: RV016 / RV042 / RV082 Internal Port Forwarding?
May 16, 2012I'd like to setup a WCCP in those routers, but as I read, it's not possible.
Another way to circumvent this limitation is to foward a request to the router from the LAN port 80 to a LAN IP, something like:
LAN 1 192.168.1.100:80 -> router -> LAN 2 192.168.1.101:80
Dell :: D620 WLAN Utility Won't Launch - Internal Configuration Is Inconsistent
Oct 15, 2006Wireless card is Dell Wirele4ss 1490 Dual Band WLAN Mini-Card
Each time I try to launch the Dell WLAN Utility I get a message:
"Internal configuration is inconsistent. Please restart the machine to resolve the problem."
Restarting does not solve the problem.
The wireless card connects fine with Windows managing the connection. But what about the Dell Utility? What can be done so it will launch and I can let it manage the wireless connections?
I have reinstalled the Driver and utility using R115319.EXE
Cisco Firewall :: ASA5505 Configure Port Forwarding To Multiple Internal IP Addresses
Jun 21, 2012ASA 5505 Firmware 8.3(4), ADSM 6.4(2).I have a public IP address of 168.87.3.4.I need to forward ports (5060, 5080, etc.) to one internal address. (192168.1.1).I need to foward different ports (10020-10080) to a different internal address (192.168.1.2) Everything I read tells me how to do this in a 1 to 1 static NAT.
View 1 Replies View RelatedCisco Switching/Routing :: Change Number Of Internal Port-channel On Nexus 5000
Jan 3, 2012I'm in the middle of a Nexus 5000 project and recognized today while configuring port-channels, that some of the interface numbers are reserved for internal use.
Is it possible to change or configure which port-channel interface numbers are allocated for internal use by NX-OS?
Unfortunatly I wasn't able to find a solution for this issue in the offical Nexus documentation, the search function of this forum or Google. If I did miss something or didn't look careful enough at the Nexus docs, I'm also happy with RTFM (... fine manual) responses and links to the info :-)
Additional info:
Nexus5k(config)# interface port-channel 128 ignored port-channel128: internally used, configuration not allowed
Port-Channels 111, 113, 115, 119, 121, 200, 211, 222 were created manually, but 127 - 129 were not.
Nexus5k# show port-channel usage
Total 11 port-channel numbers used
============================================
Used : 111 , 113 , 115 , 119 , 121 , 127 - 129 , 200 , 211 , 222
Unused: 1 - 110 , 112 , 114 , 116 - 118 , 120 , 122 - 126 , 130 - 199
201 - 210 , 212 - 221 , 223 - 4096
[Code]......
Dell :: How To Use Sim Card In Xps15
Nov 2, 2011how to use sim card in dell xps15
View 6 Replies View RelatedWireless Card For Dell Optiplex 745?
Dec 29, 2012What wireless card should i buy for Dell Optiplex 745?
View 2 Replies View RelatedDell :: Inspiron 530 Wi-Fi Card Won't Turn On
Jan 26, 2012I had turned my computer on and I hadn't been on it in a week or 2 because for some reason my computers WiFi connector was not turning on in the back. Usually, if the wifi is turned on, there is a green light flashing in the back which tells me it is picking up or searching for a signal. And once I turned it on, it had started working again. So I played on it a bit and got off. But when I went to turn it on today, it wont pick up any signals. My router is working perfectly fine since I'm typing this on my iPad.
View 1 Replies View RelatedDell :: Studio 540 - Wireless Card
Jan 5, 2009I have a new Dell Studio 540. It is presently plugged into a wired router via an Ethernet cable. However according to the documentation I should also have a wireless card fitted. It should have the following fitted:
Wireless Network Card 1505 PCIe 802.11n
How I find out this information.
Dell :: Wireless Card Seems Slow On XPS 14z
Nov 25, 2011I just got a XPS 14z. The wireless signal isn't consistent and it is weaker than my old XPS 1330. It's actually painfully slow. Every thing is exactlly the same. I have my old computer next to the new computer and the wireless signal is working much better on the old computer. Pages are loading more quickly on the older model. Howothers wireless is performing on their 14z? There is nothing wrong with the router or internet connection.
View 135 Replies View RelatedDell :: Wi-Fi Card For Inspiron One 2320?
Apr 11, 2013I'm looking for a part number for the internal wifi card on a Dell Inspiron One 2320. If not a part number, then what the generic model is that is installed in the all-in-one 2320 that would be great. Need to replace a faulty one and Service Tag doesn't determine proper card.
View 4 Replies View RelatedDell :: Wireless Card For XPS 8300?
Jun 2, 2012Which wireless card would you recommend for my Dell XPS 8300 desktop? It has an Intel iCore 7 CPU with 16 GB ram running on Windows 7. There are three empty PCI Express x1 slots. The router is an old Linksys Wireless Broadbank Router, 2.4 GHz, 802.11g, purchased back in 2005.
View 5 Replies View Related
